LEMON Manuals: Even more car manuals for everyone

Fuel Injector: Inspection

  1. INSPECT FUEL INJECTOR ASSEMBLY 
    1. Check the resistance.
      1. Using an ohmmeter, measure the resistance between the terminals.

        Standard 

        TESTER CONNECTION SPECIFIED CONDITION REFERENCE CHART

        Tester Connection Specified Condition
        1 - 2 11.6 to 12.4 Ω at 20°C (68°F)

        If the result is not as specified, replace the fuel injector.

        Fig 1: Inspecting Fuel Injector Assembly
        G04962629Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check the injection volume.
      NOTE:
      • Perform the test in a well-ventilated area and watch out for flames.
      • Handle the fuel tube connector carefully.
      Fig 2: Checking Injection Volume
      G04962630Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Install the SST (fuel tube connector) into SST (hose), then connect the tube connector to the fuel pipe.

        SST 09268-31012 (95336-08070, 09268-41091), 09268-41140, 09268-41400 (09268-41500), 09842-30080 

      2. Remove the pressure regulator (see FUEL PRESSURE REGULATOR ).
      3. Install the O-ring onto the fuel inlet of the pressure regulator.
        Fig 3: Identifying SST (Hose), SST (Fuel Tube Connector) And Fuel Pipe
        G06088522Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      4. Connect SST (hose) to the fuel inlet of the pressure regulator with another SST (union) and the 2 bolts.

        SST 09268-31012 (95336-08070, 09268-41091) 

        Torque: 9.0 N*m (92 kgf*cm, 80 in.*lbf) 

      5. Connect the fuel return hose to the fuel outlet of the pressure regulator.
        Fig 4: Identifying SST (Hose), SST (Union), Pressure Regulator, Fuel Return Hose And Bolts
        G04962633Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      6. Install a new O-ring onto the injector.
      7. Connect SST (adaptor and hose) to the injector and hold the injector and union with SST (clamp).

        SST 09268-31012 (95336-08070), 09268-41140, 09268-41400 

      8. Set the injector in a graduated cylinder.
        CAUTION: Install a suitable vinyl tube onto the injector to prevent gasoline splashes.
        Fig 5: Connecting SST (Adaptor And Hose) To Injector
        G04962634Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      9. Connect the Techstream to the DLC3.
      10. Turn the ignition switch to ON.
      11. Turn the Techstream ON.
      12. Enter the following menu:

        Select: Data List/Powertrain/Engine and ECT/Active Test/Control the Fuel Pump Speed.

      13. Install SST onto the fuel injector.

        SST 09842-30080 

      14. Connect SST to the battery, then measure the injection volume for 15 seconds. Perform the inspection 2 or 3 times, then calculate the average.

        Standard: 

        INJECTION VOLUME REFERENCE CHART

        Injection Volume Difference Between Each Fuel Injector
        76 to 91 cm3 (4.6 to 5.5 cu In.) per 15 seconds 15 cm3 (0.9 cu fn.) or less
        NOTE: Always do the switching at the battery side.

        If the result is not as specified, replace the fuel injector.

        Fig 6: Connecting SST To Battery
        G05109635Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Check the fuel leakage.
      1. When checking the injection volume, remove SST from the battery. Inspect the fuel leakage from the fuel injector.

        Standard: 

        1 drop or less every 12 minutes. 

        If the result is not as specified, replace the fuel injector.