LEMON Manuals: Even more car manuals for everyone

Inspection Procedure

NOTE: The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read precaution for the Supplemental Restraint System (See AIRBAG SYSTEM ).
  1. INSPECT RADIO RECEIVER ASSEMBLY 
    1. Disconnect the R3 radio receiver assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance 

      RESISTANCE SPECIFICATION

      Tester Connection Condition Specified Condition
      R3-7 (SW1) - R3-6 (SWG) No switch Is pushed 95 to 105 kΩ
      Seek+ switch: pushed Below 2.5 Ω
      Seek- switch: pushed 312.5 to 345.5 Ω
      Volume+ switch: pushed 950 to 1050 Ω
      Volume- switch: pushed 2954.5 to 3265.5 Ω
      R3-8 (SW2) - R3-6 (SWG) No switch is pushed 95 to 105 kΩ
      MODE switch: pushed Below 2.5 Ω
      Voice switch: pushed(1) 2954.5 to 3265.5 Ω
      On Hook switch: pushed(1) 312.5 to 345.5 Ω
      Off Hook switch: pushed(1) 950 to 1050 Ω
      (1) w/ Stereo Component Amplifier Assembly
      Fig 1: Identifying R3 Radio Receiver Assembly Connector Terminals
      G06084701Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the radio receiver assembly connector.

    NG: Go to step 2 

    OK: PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE  (See PROBLEM SYMPTOMS TABLE )

  2. INSPECT STEERING PAD SWITCH ASSEMBLY 
    1. Disconnect the steering pad switch assembly connector.
      Fig 2: Inspecting Steering Pad Switch Assembly
      G06084702Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance 

      RESISTANCE SPECIFICATION

      Tester Connection Condition Specified Condition
      10 (AU1) - 8 (EAU) No switch is pushed 95 to 105 kΩ
      Seek+ switch: pushed Below 2.5 Ω
      Seek- switch: pushed 312.5 to 345.5 Ω
      Volume+ switch: pushed 950 to 1050 Ω
      Volume- switch: pushed 2954.5 to 3265.5 Ω
      9 (AU2) - 8 (EAU) No switch Is pushed 95 to 105 kΩ
      MODE switch: pushed Below 2.5 Ω
      Voice switch: pushed(1) 2954.5 to 3265.5 Ω
      ON HOOK switch: pushed(1) 312.5 to 345.5 Ω
      OFF HOOK switch: pushed(1) 950 to 1050 Ω
      (1) for Double Cab with 7 Speakers
    3. Reconnect the radio receiver assembly connector.

      NG: REPLACE STEERING PAD SWITCH ASSEMBLY  (See REMOVAL )

      OK: Go to next step. 

  3. INSPECT SPIRAL CABLE SUB-ASSEMBLY 
    1. Disconnect the S8 spiral cable sub-assembly connector.
    2. Disconnect the steering pad switch assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance 

      RESISTANCE SPECIFICATION

      Tester Connection Condition Specified Condition
      8 (EAU) - S8-4 (EAU) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right
      10 (AU1) - S8-6 (AU1) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right
      9 (AU2) - S8-5 (AU2) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right
      NOTE: The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the precaution for the SRS (See SPIRAL CABLE ).
    4. Reconnect the radio receiver assembly connector.

    NG: REPLACE SPIRAL CABLE SUB-ASSEMBLY  (See SPIRAL CABLE )

    Fig 3: Inspecting Spiral Cable Sub-Assembly
    G06084703Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    OK: REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)