Terminals Of Ecu
- CHECK DRIVER SIDE JUNCTION BLOCK (MAIN BODY ECU)
- Disconnect the 1A, 1B, 1D, 1E and 1J junction block connectors.
- Measure the resistance and voltage of the wire harness side connectors.CONNECTOR TERMINALS REFERENCE CHART
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition GND (1E-17) - Body ground W-B - Body ground Ground Always Below 1 Ω SIG (1B-1) - Body ground W - Body ground Ignition power supply Power switch OFF Below 1 V Power switch ON (IG) 10 to 14 V ACC (1J-5) - Body ground G - Body ground Ignition power supply Power switch OFF Below 1 V Power switch ON (ACC) 10 to 14 V ECUB (1A-30) - Body ground R - Body ground +B (ECUB) power supply Always 10 to 14 V KSW (1E-23) - Body ground Y - Body ground Key unlock warning switch input No key in key slot 10 kΩ or higher Key inserted Below 1 Ω KSW (1E-26) - Body ground No key in key slot 10 kΩ or higher Key inserted Below 1 Ω DCTY (1D-21) - Body ground V - Body ground Driver side door courtesy switch input Driver side door closed 10 kΩ or higher Driver side door open Below 1 Ω PCTY (1D-24) - Body ground BR - Body ground Passenger side door courtesy switch input Passenger side door closed 10 kΩ or higher Passenger side door open Below 1 Ω BCTY (1D-7) - Body ground R- Body ground Back door courtesy switch input Back door closed 10 kΩ or higher Back door open Below 1 Ω If the result is not as specified, there may be a malfunction on the wire harness side.
- Reconnect the 1A, 1B, 1D, 1E and 1J junction block connectors.
- Measure the voltage of the connectors.CONNECTOR TERMINALS REFERENCE CHART
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition HAZ (1L-17) - Body ground Y - Body ground Hazard warning light drive Answer-back OFF Below 1 V Answer-back ON Pulse generation RDA (B7-23) - Body ground L- Body ground Door control receiver input Transmitter switch OFF (power switch OFF and all door closed) Below 1 V Transmitter switch ON (power switch OFF and all door closed) Pulse generation If the result is not as specified, the junction block (ECU) have a malfunction.
- CHECK CERTIFICATION ECU
- Disconnect the S11 ECU connector.
- Measure the resistance and voltage of the wire harness side connector.CONNECTOR TERMINALS REFERENCE CHART
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition E (S11-17) - Body ground W-B - Body ground Ground Always Below 1 Ω +B1 (S11-1) - E (S11-17) R - W-B Battery power supply Always 10 to 14 V IG (S11-18) - E (S11-17) B - W-B Ignition power supply Power switch OFF Below 1 V Power switch ON (IG) 10 to 14 V If the result is not as specified, there may be a malfunction on the wire harness side.
- Reconnect the S11 ECU connector.
- Measure the voltage of the connector.CONNECTOR TERMINALS REFERENCE CHART
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition RSSI (S11-11) - E (S11-17) V - W-B Door control receiver output signal Transmitter switch OFF (power switch OFF and all doors closed) 5 to 0 V Transmitter switch ON (power switch OFF and all doors closed) Below 1 V RDA (S11-10) - E (S11-17) GR - W-B Door control receiver input signal Transmitter switch OFF (power switch OFF and all doors closed) Below 1 V Transmitter switch ON (power switch OFF and all doors closed) Alternating between 6 to 7 V and below 1 V CLG1 (S11-13) - E (S11-17) P - W-B Driver door oscillator sensor signal Power switch OFF (all doors open with key from outside vehicle) Pulse generation Power switch ON (IG) (all doors open with key from outside vehicle) No pulse SEL1 (S11-23) - E (S11-17) Y - W-B Driver door oscillator sensor signal Key placed at least 3 m (9.84 ft.) from driver door 10 to 14 V Place key close to front door outside handle RH Below 1 V If the result is not as specified, the ECU may have a malfunction.