LEMON Manuals: Even more car manuals for everyone

Knock Sensor: Removal

  1. DISCHARGE FUEL SYSTEM PRESSURE 

    (See FUEL SYSTEM )

  2. REMOVE ENGINE ROOM SIDE LH COVER (See  REMOVAL  ) 
  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
  4. DRAIN COOLANT (See  COOLANT  ) 
  5. REMOVE FRONT SUSPENSION BRACE SUBASSEMBLY UPPER CENTER (See step 16 in  REMOVAL  ) 
  6. REMOVE AIR CLEANER CAP W/ INLET (See  ON-VEHICLE INSPECTION  ) 
  7. REMOVE AIR CLEANER CASE W/ RESONATOR (See  REMOVAL  ) 
  8. SEPARATE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY (See step 38 in  REMOVAL  ) 
  9. REMOVE RESERVOIR BRACKET (See step 39 in  REMOVAL  ) 
  10. REMOVE AIR CLEANER BRACKET (See step 40 in  REMOVAL  ) 
  11. REMOVE ENGINE MOVING CONTROL ROD (See  REMOVAL  ) 
  12. REMOVE EMISSION CONTROL VALVE SET 
    1. Disconnect the VSV connector (A).
    2. Remove the wire harness clamp (B).
    3. Disconnect the fuel vapor feed hose No. 1 (C).
    4. Disconnect the fuel vapor feed hose No. 2 (D).
    5. Remove the 2 nuts (E), then remove the emission control valve set.
    Fig 1: Disconnecting Fuel Vapor Feed Hose No.1 (C)
    G04441448Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE INTAKE AIR SURGE TANK 
    1. Disconnect the throttle motor connector (A).
    2. Separate the water bypass hose No. 2 (B).
    3. Separate the water bypass hose No. 3 (C).
    4. Separate the fuel vapor feed hose (D).
      Fig 2: Disconnecting Throttle Motor Connector (A)
      G04441449Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disconnect the ventilation hose.
      Fig 3: Disconnecting Ventilation Hose
      G04441450Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Remove the 2 bolts, then remove the engine hanger No.1 (A).
    7. Remove the 2 bolts, then remove the surge tank stay No. 1 (B).
    8. Remove the 2 bolts, then remove the surge tank stay No. 2 (C).
      Fig 4: Removing Engine Hanger No.1 (A) And Bolts
      G04441451Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    9. Disconnect the ground cable connector.
    10. Using a socket hexagon wrench 8 mm, remove the 4 bolts.
    11. Remove the 2 nuts, then remove the emission control valve bracket and the intake air surge tank.
    12. Remove the gasket from the intake air surge tank.
    Fig 5: Disconnecting Ground Cable Connector And Nuts
    G04441452Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. DISCONNECT FUEL PIPE SUB-ASSEMBLY 
    1. Remove the EFI fuel pipe clamp No.1.
    2. Pinch the quick connector and then pull out the fuel pipe No. 1.
      NOTE:
      • Remove dirt or foreign objects on the quick connector before this work.
      • Do not to allow any scratches or foreign objects on the parts when disconnecting as the fuel hose connector has the O-ring that seals the pipe.
      • Perform this work by hand. Do not use any tools.
      • Do not forcibly bend, twist or turn the nylon tube.
      • Protect the connected part by covering it with a vinyl bag after disconnecting the hose.
      • If the quick connector and pipe are stuck, push and pull them to release.
    Fig 6: Removing EFI Fuel Pipe Clamp No.1
    G04441453Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. DISCONNECT HEATER WATER INLET HOSE 
    1. Disconnect the heater water inlet hose.
    Fig 7: Disconnecting Heater Water Inlet Hose
    G04441454Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. DISCONNECT RADIATOR HOSE INLET 
    1. Disconnect the radiator hose inlet.
    Fig 8: Disconnecting Radiator Hose Inlet
    G04441455Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE INTAKE MANIFOLD 
    1. Remove the nut and ground cable.
      Fig 9: Removing Nut And Ground Cable
      G04441456Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the 6 fuel injector connectors.
      Fig 10: Disconnecting Fuel Injector Connectors
      G04441457Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. In order to remove the intake manifold, using several steps, remove the 9 bolts and 2 nuts in the sequence shown in the illustration.
  18. REMOVE WATER OUTLET (See step 25 in  REMOVAL  ) 
    Fig 11: Removing Intake Manifold Bolts And Nuts
    G04441458Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE KNOCK CONTROL SENSOR 
    1. Disconnect the 2 knock sensor connectors.
    2. Remove the 2 nuts, and then remove the 2 knock sensors.
    Fig 12: Disconnecting Knock Sensor Connectors And Nuts
    G04441459Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002