Data List / Active Test
- DATA LIST
HINT:
With the intelligent tester connected to the DLC3 and the ignition switch ON, the ECB, ABS, and VSC data list can be displayed. Follow the prompts on the tester screen to access the DATA LIST.
ABS / VSC:
DATA LIST CHARTItem (Display) Measurement Item/Range (Display) Normal Condition Diagnostic Note ABS WARN LAMP ABS warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- VSC WARN LAMP VSC warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- BRAKE WARN LAMP BRAKE warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- SLIP INDI LAMP SLIP indicator light / ON or OFF ON: Indicator light ON
OFF: Indicator light OFF- ECB WARN LAMP ECB warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- BUZZER Skid control buzzer / ON or OFF ON: Buzzer ON
OFF: Buzzer OFF- STOP LAMP SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- PARKING BRAKE SW Parking brake switch / ON or OFF ON: Parking brake applied
OFF: Parking brake released- RESERVOIR SW Brake fluid level warning switch / ON or OFF ON: Reservoir level normal
OFF: Reservoir level low- IDLE SW Main idle switch / ON or OFF ON: Accelerator pedal released
OFF: Accelerator pedal depressed- LEVER POSITION Shift lever position information / P/N, R, D/M, 1st-6th/B, FAIL - - MAS CYL PRESS 1 Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V Reading increases when brake pedal is depressed VOLT M/C SEN Voltage of master cylinder pressure sensor / min.: -2.5 V, max.: 2.49 V - - MAS CYL PRESS 2 Master cylinder pressure sensor 2 reading / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V Reading increases when brake pedal is depressed VOLT M/C SEN 2 Voltage of master cylinder pressure sensor 2 / min.: -2.5 V, max.: 2.49 V - - PEDAL STROKE Stroke sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.7 to 1.3 V - VOLT STROK SEN Voltage of stroke sensor / min.: - 2.5 V, max.: 2.49 V - - PEDAL STROKE 2 Stroke sensor 2 / min.: 0 V, max.: 5 V When brake pedal is released: 3.7 to 4.3 V - VOLT STROK SEN 2 Voltage of stroke sensor 2 / min.: -2.5 V, max.: 2.49 V - - ACC PRESS SENS Accumulator pressure sensor / min.: 0 V, max.: 5 V Specified value: 3.2 to 4.0 V - DECELERAT SEN Deceleration sensor 1 reading / min.: -18.52 m/s2 , max.: -18.33 m/s2 Approximately m/s2 while stationary Reading changes when vehicle is bounced ZERO DECELERAT Memorized zero value / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- ABS WARN LAMP ABS warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- VSC WARN LAMP VSC warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- BRAKE WARN LAMP BRAKE warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- SLIP INDI LAMP SLIP indicator light / ON or OFF ON: Indicator light ON
OFF: Indicator light OFF- ECB WARN LAMP ECB warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- BUZZER Skid control buzzer / ON or OFF ON: Buzzer ON
OFF: Buzzer OFF- STOP LAMP SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- DECELERAT SEN 2 Deceleration sensor 2 reading / min.: -18.52 m/s2 , max.: -18.33 m/s2 Approximately m/s2 while stationary Reading changes when vehicle is bounced ZERO DECELERAT 2 Memorized zero value / min.: - 25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- YAW RATE SENS 1 Yaw rate sensor 1 / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- ZERO YAW RATE Memorized zero value / min.: - 128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- YAW RATE SENS 2 Yaw rate sensor 2 / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- ZERO YAW RATE 2 Memorized zero value / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- STEERING SEN Steering angle sensor / min.: -3276.8 deg, max.: 3276.7 deg Left turn: Increase
Right turn: Decrease- ZERO STEERING Memorized zero value / min.: - 3276.8 deg, max.: 3276.7 deg Min.: -3276.8 deg
Max.: 3276.7 deg- FR W/C SENS FR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released:
0.3 to 0.9 V- FL W/C SENS FL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released:
0.3 to 0.9 V- RR W/C SENS RR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released:
0.3 to 0.9 V- RL W/C SENS RL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released:
0.3 to 0.9 V- LATERAL G Lateral G / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- FORWARD & REA G Forward and rearward G / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- YAW RATE VALUE Yaw rate value / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
Max.: 127 deg/s- STEERING ANGLE Steering angle value / min.: - 3276.8 deg, max.: 3276.7 deg Min.: -3276.8 deg
Max.: 3276.7 deg- FR WHEEL SPD Wheel speed sensor (FR) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual wheel speed Similar speed as indicated on speedometer FL WHEEL SPD Wheel speed sensor (FL) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual wheel speed Similar speed as indicated on speedometer RR WHEEL SPD Wheel speed sensor (RR) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual wheel speed Similar speed as indicated on speedometer ABS WARN LAMP ABS warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- VSC WARN LAMP VSC warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- BRAKE WARN LAMP BRAKE warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- SLIP INDI LAMP SLIP indicator light / ON or OFF ON: Indicator light ON
OFF: Indicator light OFF- ECB WARN LAMP ECB warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- BUZZER Skid control buzzer / ON or OFF ON: Buzzer ON
OFF: Buzzer OFF- STOP LAMP SW Stop light switch / ON or OFF ON: Brake pedal depressed OFF: Brake pedal released - RL WHEEL SPD Wheel speed sensor (RL) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual wheel speed Similar speed as indicated on speedometer VEHICLE SPD Maximum wheel speed sensor reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual vehicle speed Speed indicated on speedometer FR WHEEL ACCEL FR wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- FL WHEEL ACCEL FL wheel acceleration / min.: - 200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- RR WHEEL ACCEL RR wheel acceleration / min.: - 200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- RL WHEEL ACCEL RL wheel acceleration / min.: - 200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- FR ABS STATUS FR wheel ABS control status / ON or OFF ON: During the control - FL ABS STATUS FL wheel ABS control status / ON or OFF ON: During the control - RR ABS STATUS RR wheel ABS control status / ON or OFF ON: During the control - RL ABS STATUS RL wheel ABS control status / ON or OFF ON: During the control - TRAC STATUS TRAC control status / ON or OFF ON: During the control - TRAC BRK STATUS TRAC brake control status / ON or OFF ON: During the control - FR VSC STATUS FR wheel VSC control status / ON or OFF ON: During the control - FL VSC STATUS FL wheel VSC control status / ON or OFF ON: During the control - RR VSC STATUS RR wheel VSC control status / ON or OFF ON: During the control - RL VSC STATUS RL wheel VSC control status / ON or OFF ON: During the control - ACCELERATOR % Accelerator Opening Angle / min.: 0 %, max.: 128 % Accelerator pedal released: 0 % - FR RQST TORQ Front regenerative request torque / min.: 0 N*m, max.: 4,080 N*m - - FR OPERATE TORQ Front regenerative operation torque / min.: 0 N*m, max.: 4,080 N*m - - RR RQST TORQ Rear regenerative request torque / min.: 0 N*m, max.: 4,080 N*m - - ABS WARN LAMP ABS warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- VSC WARN LAMP VSC warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- BRAKE WARN LAMP BRAKE warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- SLIP INDI LAMP SLIP indicator light / ON or OFF ON: Indicator light ON
OFF: Indicator light OFF- ECB WARN LAMP ECB warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- BUZZER Skid control buzzer / ON or OFF ON: Buzzer ON
OFF: Buzzer OFF- STOP LAMP SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- RR OPERATE TORQ Rear regenerative operation torque / min.: 0 N*m, max.: 4,080 N*m - - REGEN COOP Regenerative cooperation / ON or OFF ON: Operate - OFF: Not operate - ECB MTR RELAY ECB motor relay / ON or OFF ON: Motor relay ON
OFF: Motor relay OFF- ECB MTR RELAY 2 ECB motor relay 2 / ON or OFF ON: Motor relay ON
OFF: Motor relay OFF- ECB RELAY ECB main relay / ON or OFF ON: Main relay ON
OFF: Main relay OFF- ECB RELAY 2 ECB main relay 2 / ON or OFF ON: Main relay ON
OFF: Main relay OFF- SMC1 ECB solenoid (SMC1) / ON or OFF ON: Operate
OFF: Not operate- SMC2 ECB solenoid (SMC2) / ON or OFF ON: Operate
OFF: Not operate- SCSS ECB solenoid (SCSS) / ON or OFF ON: Operate
OFF: Not operate- SLAFR CUR SLAFR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLAFL CUR SLAFL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLARR CUR SLARR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLARL CUR SLARL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRFR CUR SLRFR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRFL CUR SLRFL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRRR CUR SLRRR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRRL CUR SLRRL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - FR SPD OPN FR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- FL SPD OPN FL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- RR SPD OPN RR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- RL SPD OPN RL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- ABS WARN LAMP ABS warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- VSC WARN LAMP VSC warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- BRAKE WARN LAMP BRAKE warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- SLIP INDI LAMP SLIP indicator light / ON or OFF ON: Indicator light ON
OFF: Indicator light OFF- ECB WARN LAMP ECB warning light / ON or OFF ON: Warning light ON
OFF: Warning light OFF- BUZZER Skid control buzzer / ON or OFF ON: Buzzer ON
OFF: Buzzer OFF- STOP LAMP SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- YAW RATE OPN Yaw rate sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- DECELERAT OPN Deceleration sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- STEERING OPN Steering angle sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- M/C OPN Master cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- M/C2 OPN Master cylinder pressure sensor 2 open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- STROKE OPN Stroke sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- FR W/C OPN FR wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- FL W/C OPN FL wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- RR W/C OPN RR wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- RL W/C OPN RL wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- ACC OPN Accumulator pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- HV COM OPN HV control ECU open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal- # DTC Number of DTC recorded / min.: 0, max.: 255 - - - ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the intelligent tester allows the relay, actuator, etc. to operate without removing any parts. Performing the ACTIVE TEST as the first step of troubleshooting is one of the methods to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch on.
- According to the display on the tester, perform the "ACTIVE TEST".
HINT:
The ignition switch must be turned to the ON position to proceed to the ACTIVE TEST using the intelligent tester.
ABS / VSC:
ACTIVE TEST CHARTItem (Display) Vehicle Condition / Test Details Diagnostic Note ABS WARN LAMP Turns ABS warning light ON / OFF Observe combination meter VSC WARN LAMP Turns VSC warning in multi information display ON / OFF Observe combination meter BRAKE WARN LAMP Turns BRAKE warning light ON / OFF Observe combination meter SLIP INDI LAMP Turns SLIP indicator light ON / OFF Observe combination meter ECB WARN LAMP Turns brake control warning light ON / OFF Observe combination meter BUZZER Turns skid control buzzer ON / OFF Buzzer can be heard STP LAMP RELAY Turns stop light operation relay ON / OFF Observe rear combination light (stop light) (Does not come on for 5 sec. or more) ECB RELAY Turns ABS No.1 relay ON / OFF Operating sound of relay (clicking sound) can be heard ECB RELAY 2 Turns ABS No.2 relay ON / OFF Operating sound of relay (clicking sound) can be heard ECB MTR RELAY Turns ABS MTR1 motor relay ON / OFF Operating sound of relay (clicking sound) can be heard ECB MTR RELAY 2 Turns ABS MTR2 relay ON / OFF Operating sound of relay (clicking sound) can be heard SMC1 Turns ECB solenoid (SMC1) ON / OFF Operating sound of solenoid (clicking sound) can be heard SMC2 Turns ECB solenoid (SMC2) ON / OFF Operating sound of solenoid (clicking sound) can be heard ECB INVALID ECB Control Invalid ON / OFF ECB control is blocked (braking with no boost assist) ZERO DOWN Accumulator Zero Down Activation ON / OFF Brake fluid existing the accumulator makes noise SCSS PATTERN Stroke Simulator Cut Valve Pattern Activation ON / OFF -
(Difficult to identify visually)ACT PATTERN Actuator Air Bleeding Pattern Activation ON / OFF When accumulator pressure lowers, pump operation creates sound POWER SUPPLY1 Power Supply Air Bleeding Pattern Activation 1 ON / OFF When accumulator pressure lowers, pump operation creates sound POWER SUPPLY2 Power Supply Air Bleeding Pattern Activation 2 ON / OFF When accumulator pressure lowers, pump operation creates sound RL AIR BLEEDING RL Wheel Air Bleeding Pattern Activation ON / OFF When accumulator pressure lowers, pump operation creates sound RR AIR BLEEDING RR Wheel Air Bleeding Pattern Activation ON / OFF When accumulator pressure lowers, pump operation creates sound PUMP PATTERN Pump Check Pattern Activation ON / OFF When accumulator pressure lowers, pump operation creates sound DRAIN PATTERN Drain System Air Bleeding Pattern Activation ON / OFF When accumulator pressure lowers, pump operation creates sound SLRRL CLOSED Turns SLRRL solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard SLARL CLOSED Turns SLRRL solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard SLRRR CLOSED Turns SLRRL solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard SLARR CLOSED Turns SLRRL solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard SLRFL CLOSED Turns SLRRL solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard SLAFL CLOSED Turns SLRRL solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard SLRFR CLOSED Turns SLRRL solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard SLAFR CLOSED Turns SLRRL solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard