LEMON Manuals: Even more car manuals for everyone

Combination Meter: Inspection

  1. INSPECT SPEEDOMETER ON-VEHICLE 

    Using a speedometer tester, inspect the speedometer for allowable indication error and check odometer operation.

    HINT:

    Tire wear and tire over or under inflation will increase the indication error.

    SPEEDOMETER RANGE

    USA (mph) CANADA (km/h)
    Standard indication : Allowable range Standard indication : Allowable range
    20 : 19 - 22 20 : 17.5 - 21.5
    40 : 39 - 42.5 40 : 38 - 42
    60 : 59.5 - 63.5 60 : 58 - 63
    80 : 79.5 - 84 80 : 78 - 84
    100 : 100 - 105 100 : 98.5 - 104.5
    - 120 : 119 - 125
    - 140 : 139 - 145
    - 160 : 159 - 167

    If error is excessive, replace the speedometer.

  2. INSPECT TACHOMETER 
    1. Connect a tune-up test tachometer, and start the engine.
      NOTE:
      • Reversing the connection of the tachometer will damage the transistors and diodes inside.
      • When removing or installing the tachometer, be careful not to drop or subject it to heavy shocks.
    2. Compare the tester and tachometer indications.

      DC 13.5 V 20° C at (68° F) 

      TACHOMETER RANGE

      Standard indication Allowable range
      700 630 - 770
      1,000 900 - 1,100
      2,000 1,850 - 2,150
      3,000 2,800 - 3,200
      4,000 3,800 - 4,200
      5,000 4,800 - 5,200
      6,000 5,750 - 6,250

      If error is excessive, replace the tachometer.

  3. INSPECT FUEL RECEIVER GAUGE OPERATION 
    1. Disconnect the connector from the sender gauge.
    2. Turn the ignition switch ON and check that the receiver gauge needle indicates EMPTY.
      Fig 1: Turning Ignition Switch On & Checking Receiver Gauge Needle Indicates EMPTY
      G03056713Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Connect terminals 2 and 3 on the wire harness side connector through a 3.4 watts test bulb.
    4. Turn the ignition switch ON, check that the bulb comes on and the receiver gauge needle moves towards the full side.
      Fig 2: Turning Ignition Switch On, Checking Bulb Comes On & Receiver Gauge Needle Moves Towards Full Side
      G03056714Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT:

      Because of silicon oil in the gauge, it will take a short time for the needle to stabilize.

      If operation is not as specified, inspect the receiver gauge resistance.

  4. INSPECT FUEL LEVEL WARNING LIGHT OPERATION 
    1. Disconnect the connector from the sender gauge.
    2. Connect terminals 2 and 3 on the wire harness side connector.
    3. Turn the ignition switch ON and check that the warning light comes on.

      If the warning light does not come on, test the bulb or inspect the wire harness.

      Fig 3: Turning Ignition Switch On & Checking Warning Light Comes On
      G03056715Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. INSPECT ENGINE COOLANT TEMPERATURE SENDER GAUGE RESISTANCE 
    1. Disconnect the engine coolant temperature sender gauge.
    2. Measure the resistance between terminals 1 and 2 of the connector according to the value(s) in the table below.
      Fig 4: Identifying Resistance Between Terminals 1 & 2
      G03056716Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      RESISTANCE CONDITION

      Temperature °C (°F) Resistance (Ω)
      -20 (-4) 13,840 to 16,330
      20 (68) 2,320 to 2,590
      80 (176) 310 to 326
      110 (230) 139.9 to 143.5

      If resistance value is not as specified, replace the engine coolant sender gauge.

  6. INSPECT OIL PRESSURE SENDER OPERATION 
    1. Disconnect the connector from the oil pressure sender.
    2. Check that no continuity exists between terminal and ground with the engine stopped.
    3. Check that continuity exists between terminal and ground with the engine running.
      Fig 5: Checking Continuity Exists Between Terminal & Ground With Engine Running/Stopped
      G03056717Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT:

      Oil pressure should be over 24.5 kPa (0.25 kgf/cm2 , 3.55 psi).

      If operation is not as specified, replace the oil pressure sender.

  7. INSPECT BRAKE WARNING LIGHT OPERATION 
    1. Disconnect the connector from the brake fluid warning switch.
    2. Release the parking brake pedal.
    3. Connect the terminals on the harness side of the level warning switch connector.
    4. Fig 6: Connecting Terminals On Harness Side Of Level Warning Switch Connector
      G03056718Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Start the engine and check that the warning light comes on.

      If the warning light does not come on, test the bulb or wire harness.

  8. INSPECT BRAKE FLUID LEVEL WARNING SWITCH CONTINUITY 
    1. Remove the reservoir tank cap and strainer.
    2. Disconnect the connector.
    3. Check that no continuity exists between the terminals with the switch OFF (float up).
    4. Use siphon, etc. to drain fluid out of the reservoir tank.
    5. Check that continuity exists between the terminals with the switch ON (float down).
    6. Pour the fluid back in the reservoir tank.

      If continuity is not as specified, replace the switch.

      Fig 7: Checking That No Continuity Exists Between Terminals With Switch Off (Float Up)
      G03056719Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. INSPECT PARKING BRAKE SWITCH CONTINUITY 
    1. Check that continuity exists between the terminal and switch body with the switch ON (switch pin released).
    2. Check that no continuity exists between the terminal and switch body with the switch OFF (switch pin pushed in).
      Fig 8: Checking That No Continuity Exists Between Terminal & Switch Body With Switch OFF/ON
      G03056720Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If operation is not as specified, replace the switch or inspect ground point.

  10. INSPECT WASHER LEVEL WARNING LIGHT OPERATION 
    1. Disconnect the connectors from the combination meter.
    2. Connect the negative (-) lead from the battery to terminal 16.
    3. Turn the ignition switch ON and check that the warning light comes on.

      If the warning light does not come on, test the bulb.

      Fig 9: Turning Ignition Switch On & Checking That Warning Light Comes On
      G03056721Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. INSPECT WASHER LEVEL SWITCH CONTINUITY 
    1. Check that there is no continuity between terminals with the switch OFF (float up).
    2. Check that there is continuity between terminals with the switch ON (float down).
      Fig 10: Checking That There Is Continuity Between Terminals With Switch ON/OFF
      G03056722Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If operation is not as specified, replace the jar & pump assembly.

  12. INSPECT BUCKLE SWITCH CONTINUITY (See  HOW TO PROCEED WITH TROUBLESHOOTING  ) 
  13. INSPECT OPEN DOOR WARNING LIGHT OPERATION 
    1. Disconnect the connector from the door courtesy switch and ground terminal on the wire harness side connector.
    2. Fig 11: Disconnecting Connector From Door Courtesy Switch & Ground Terminal On Wire Harness Side Connector
      G03056723Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Check that the warning light comes on.

      If the warning light does not come on, test the bulb.

  14. INSPECT PASSENGER SEAT BELT WARNING LIGHT 
    1. Remove the center cluster finish panel.
    2. Disconnect the connectors from the center cluster integration.
    3. Connect the positive (+) lead from the battery to terminal 4 and the negative (-) lead to terminal 10, and check that the warning light comes on.
      Fig 12: Connecting Positive (+) Lead From Battery To Terminal 4 & Negative (-) Lead To Terminal 10 & Checking That Warning Light Comes On
      G03056724Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If the warning light does not come on, inspect the bulb or wire harness (See HOW TO PROCEED WITH TROUBLESHOOTING ).

  15. INSPECT DRIVER'S SEAT BELT WARNING BUZZER 
    1. Check warning buzzer function.
      1. Turn the ignition switch ON and check that the driver's seat belt warning buzzer sounds if the driver's seat belt is not fastened.
      2. Check that the buzzer stops after about 6 seconds.
  16. INSPECT KEY REMINDER WARNING BUZZER 
    1. Check warning buzzer function.
      1. Turn the ignition switch OFF and check that the key reminder warning buzzer sounds if the ignition key is inserted into the key cylinder and the front driver side door is opened.
  17. MAINTENANCE LIQUID RESETTING PROCEDURE 

    Indicator Condition: 

    INDICATOR CONDITION

    State Condition Specified State
    Blinking The vehicle has traveled 4,500 miles after the previous setting The indicator blinks for 12 seconds after the ignition switch is turned on (including 3 seconds for a valve check).
    Continuously Illuminated The vehicle has traveled 5,000 miles after the previous setting The indicator is continuously illuminated after the ignition switch is turned on.
    1. Set the display window to ODO.
    2. Turn the ignition switch off.
    3. Pressing the reset switch, turn the ignition switch to the ON position (keep pressing for at least 5 seconds).
    4. Reset procedure is completed.

      HINT:

      • If the ignition switch is turned off during the reset procedure, reset mode is canceled.
      • If the reset switch is turned off during the reset procedure, reset mode is canceled and the display shows the condition prior to the reset procedure.