LEMON Manuals: Even more car manuals for everyone

Evaporative Emission (EVAP) Control System: Inspection

  1. INSPECT LINES AND CONNECTIONS 

    Visually check for loose connections, sharp bends or damage.

  2. INSPECT FUEL TANK 

    Visually check for deformation, cracks or fuel leakage.

  3. INSPECT FUEL TANK CAP 

    Visually check if the cap and/or gasket are deformed or damaged.

    If necessary, repair or replace the cap.

    Fig 1: Inspecting Fuel Tank Cap
    G04271596Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSPECT EVAP SYSTEM LINE 
    1. Warm up the engine and stop the engine.

      Allow the engine to warm up to normal operating temperature.

    2. Install a vacuum gauge (EVAP control system test equipment vacuum gauge) to the EVAP service port on the purge line.
      Fig 2: Installing A Vacuum Gauge To EVAP Service Port On Purge Line
      G04271597Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Hand-held tester:

      Forced driving of the VSV for the EVAP.

      1. Connect a hand-held tester to the DLC3.
      2. Start the engine.
      3. Push the hand-held tester main switch ON.
      4. Use the ACTIVE TEST mode on the hand-held tester to operate the VSV for the EVAP.
        Fig 3: Connecting A Hand-Held Tester To Dlc3
        G04271598Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. If you have no hand-held tester:

      Forced driving of the VSV for the EVAP.

      1. Disconnect the VSV connector for the EVAP.
      2. Connect the positive (+) and negative (-) leads from the battery to the VSV terminals for the EVAP.
      3. Fig 4: Connecting Positive (+) And Negative (-) Leads From Battery To VSV Terminals For EVAP
        G04271599Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      4. Start the engine.
    5. Check the vacuum at idle.

      Vacuum: 

      Maintain at 0.368 - 19.713 in.Hg (5 - 268 in.Aq) for over 5 seconds 

      HINT:

      If the vacuum does not change, you can conclude that the hose connecting the VSV to the service port has come loose or is blocked, or the VSV is malfunctioning.

    6. If you have hand-held tester:

      Conclude forced driving of the VSV for the EVAP.

      1. Stop the engine.
      2. Disconnect the hand-held tester from the DLC3.
    7. If you have no hand-held tester:

      Conclude forced driving of the VSV for the EVAP.

      1. Stop the engine.
      2. Disconnect the positive (+) and negative (-) leads from the battery, and from the VSV terminals for the EVAP.
      3. Connect the VSV connector for the EVAP.
    8. Disconnect the vacuum gauge from the EVAP service port on the purge line.
    9. Connect a pressure gauge to the EVAP service port on the purge line.
      Fig 5: Checking Vacuum At Idle
      G04271600Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    10. If you have hand-held tester:

      Force driving of the VSV for canister closed valve (CCV)

      1. Connect a hand-held tester to the DLC3.
      2. Turn the ignition switch ON.
      3. Push the hand-held tester main switch ON.
      4. Use the ACTIVE TEST mode on the hand-held tester to operate the VSV for CCV.
      NOTE: Do not start the engine.
      Fig 6: Connecting A Hand-Held Tester To DLC3
      G04271601Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT:

      If the check is not completed within 10 minutes, the forced close of VSV for the CCV will be reset.

    11. If you have no hand-held tester:

      Forced driving of the VSV for the CCV.

      1. Disconnect the VSV connector for the CCV.
      2. Connect the positive (+) and negative (-) leads from the battery to the VSV terminals for the CCV.
      Fig 7: Connecting Positive (+) And Negative (-) Leads From Battery To VSV Terminals For CCV
      G04271602Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    12. Check the pressure.
      1. Add the pressure (13.5 - 15.5 in.Aq) from the EVAP service port.Pressure: 

        2 minutes after the pressure is added, the gauge should be over 7.7 - 8.8 in.Aq. 

        Fig 8: Checking Pressure Reading At Gauge
        G04271603Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        HINT:

        If you can't add pressure, you can conclude that the hose connecting the VSV for EVAP-canister-fuel tank has slipped off or the VSV is open.

      2. Check if the pressure decreases when the fuel tank cap is removed while adding pressure.

      HINT:

      If the pressure does not decrease when the filler cap is removed, then you can conclude that the hose connecting the service port to the fuel tank is blocked, etc.

    13. If you have hand-held tester: Conclude forced driving of he VSV for the CCV.
      1. Turn ignition switch OFF.
      2. Disconnect the hand-held tester from the DLC3.
    14. If you have no hand-held tester:

      Conclude forced driving of the VSV for the CCV.

      1. Disconnect the positive (+) and negative (-) leads from the battery, and from the VSV terminals for the CCV.
      2. Connect the VSV connector for the CCV.
    15. Disconnect the pressure gauge from the EVAP service port on the purge line.
    Fig 9: Identifying Fuel Tank Cap
    G04271604Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. CHECK AIR TIGHTNESS IN FUEL TANK AND FILLER PIPE 
    1. Disconnect the vent line hose from the fuel tank (See procedure in step  8).
    2. Apply pressure to fuel tank and make the internal pressure of the fuel tank 4 kPa (41 gf/cm2 , 0.58 psi).
    3. Check that the internal pressure of the fuel tank is maintained for 1 minute.
    4. Check the connected portions of each hose and pipe.
    5. Check the installed parts on the fuel tank.

      If there is no abnormality, replace the fuel tank and filler pipe.

    6. Reconnect the vent line hose to the fuel tank.
      Fig 10: Checking Air Tightness In Fuel Tank And Filler Pipe
      G04271605Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. INSPECT FUEL CUT OFF VALVE AND FILL CHECK VALVE 
    1. Disconnect the vent line hose from the fuel tank.
    2. Apply 4 kPa (41 gf/cm2 , 0.58 psi) to the vent port of the fuel tank.

      HINT:

      In the condition that the fuel is full, as the float valve of the fill check valve is closed and has no ventilation, it is necessary to check the fuel amount (volume).

    3. Remove the fuel tank cap, and check that pressure drops.

      If pressure does not drop, replace the fuel tank assembly.

    4. Reconnect the vent line hose to the fuel tank.
      Fig 11: Disconnecting Vent Line Hose From Fuel Tank
      G04271606Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. CHECK AIR INLET LINE 
    1. Disconnect the air inlet line hose from the charcoal canister.
    2. Check that there is ventilation in the air inlet line.
    3. Reconnect the air inlet line hose to the charcoal canister.
      Fig 12: Checking Air Inlet Line Hose
      G04271607Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE CHARCOAL CANISTER ASSEMBLY 
    1. Remove the 4 bolts, and disconnect the charcoal canister and bracket assembly from the body
    2. Remove the 4 nuts, and disconnect the charcoal canister from the bracket.
    3. Disconnect the VSV connector for the CCV.
    4. Disconnect the purge line hose and air inlet line hose from the charcoal canister.
    5. Disconnect the vent line hose from the charcoal canister.
      1. Deeply push the connector inside.
      2. Pinch portion A.
      3. Pull out the connector.
    6. Remove the charcoal canister.
      Fig 13: Removing Charcoal Canister Assembly
      G04271608Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. INSPECT CHARCOAL CANISTER 
    1. Visually check the charcoal canister for cracks or damage.
      Fig 14: Inspecting Charcoal Canister
      G04271609Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Inspect the charcoal canister operation.
      1. While holding the purge port closed, blow air (0.39 kPa, 4.0 gf/cm2 , 0.06 psi) into the vent port, and check that air flows out from the air inlet port.
        Fig 15: Checking Air Flows Out From Air Inlet Port
        G04271610Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. While holding the air inlet port closed, blow air (0.39 kPa, 4.0 gf/cm2 , 0.06 psi) into the vent port, and check that air flows out from the purge port.
        Fig 16: Checking Air Flows Out From Purge Port
        G04271611Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. While holding the air inlet port closed, apply vacuum (3.43 kPa, 25.7 gf/cm2 , 1.01 psi) to the vent port, and check that air is sucked in from the purge port.

        If operation is not as specified, replace the charcoal canister.

        Fig 17: Identifying Vent Port And Air Inlet Port
        G04271612Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Inspect the air tightness.
      1. While holding the vent and air inlet ports closed, apply vacuum (3.43 kPa, 25.7 gf/cm2 , 1.01 psi) to the purge port, and check that the vacuum is maintained for 1 minute.

      HINT:

      In order to maintain air tightness, the checked should be performed with the CCV terminal port held closed by hand.

      If operation is not as specified, replace the charcoal canister.

      Fig 18: Inspecting Air Tightness
      G04271613Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Inspect the diaphragm.
      1. Remove the air hose between ports A and B.
      2. While holding the vent, purge and air inlet ports closed, apply vacuum (1.42 kPa, 11 mmHg, 0.42 in.Hg) into port A, and check that air is sucked in from port B.
        Fig 19: Inspecting Diaphragm
        G04271614Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. While holding the vent, purge and air inlet ports closed, apply vacuum (1.42 kPa, 11 mmHg, 0.42 in.Hg) into port A, and measure how long it takes for vacuum to drop.
        Fig 20: Identifying Vent Port And Air Inlet Port
        G04271615Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      4. Vacuum drop time: 10 sec. or more 

        If operation is not as specified, replace the charcoal canister.

      5. Reinstall the air hose between ports A and B.
  10. INSPECT CHARCOAL CANISTER FILTER (See  DTC P0441: EVAPORATIVE EMISSION CONTROL SYSTEM INCORRECT PURGE FLOW; DTC P0442: EVAPORATIVE EMISSION CONTROL SYSTEM LEAK DETECTED (SMALL LEAK); DTC P0446: EVAPORATIVE EMISSION CONTROL SYSTEM VENT CONTROL CIRCUIT; DTC P0456: EVAPORATIVE EMISSION CONTROL SYSTEM LEAK DETECTED (VERY SMALL LEAK)  ) 
  11. INSPECT VSV FOR CANISTER CLOSED VALVE (See  INSPECTION  ) 
  12. INSPECT VAPOR PRESSURE SENSOR (See  INSPECTION  ) 
  13. INSPECT VSV FOR EVAP (See  INSPECTION  ) 
  14. REINSTALL CHARCOAL CANISTER ASSEMBLY