LEMON Manuals: Even more car manuals for everyone

Manual Transaxle Unit: Removal

  1. REMOVE HOOD 

    HINT:

    At the time of installation, please refer to the following item, adjust the hood (See ADJUSTMENT ).

  2. REMOVE WIPER ARM (See  REMOVAL  ) 

    HINT:

    At the time of installation, please refer to the following item, adjust the installation position of the wiper arms (See ADJUSTMENT ).

  3. REMOVE RH AND LH COWL TOP VENTILATOR LOUVERS (See  REMOVAL  ) 
  4. REMOVE NO. 2 CYLINDER HEAD COVER 

    Remove the 4 nuts and No. 2 cylinder head cover.

    Torque: 7.0 N.m (71 kgf.cm, 62 in.lbf) 

  5. REMOVE BATTERY AND AIR CLEANER CASE ASSEMBLY WITH AIR HOSE 
  6. DISCONNECT WIRE HARNESS FROM TRANSAXLE 

    Remove the set bolt of the wire harness clamp.

  7. DISCONNECT CONTROL CABLE 
    1. Remove the 2 clips and washers.
    2. Remove the 2 clips and disconnect the control cables from the transaxle.
      Fig 1: Removing Set Bolt Of Wire Harness Clamp
      G02906333Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. DISCONNECT CLUTCH RELEASE CYLINDER 
    1. Remove the set bolt of the clutch line.

      Torque: 4.9 N.m (50 kgf.cm, 43 in.lbf) 

    2. Remove the 2 set bolts of the clutch release cylinder.

      Torque: 12 N.m (120 kgf.cm, 9 ft.lbf) 

      Fig 2: Removing Bolts Of Clutch Release Cylinder
      G02906334Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. DISCONNECT GROUND CABLE 

    Remove the set bolt of the ground cable from the engine left mounting bracket.

  10. DISCONNECT BACK-UP LIGHT SWITCH AND VEHICLE SPEED SENSOR CONNECTORS 
    Fig 3: Disconnecting Ground Cable
    G02906335Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE 2 TRANSAXLE UPPER SIDE MOUNTING BOLTS 

    Torque: 33 N.m (340 kgf.cm, 25 ft.lbf) 

  12. REMOVE STARTER SET BOLT 

    Torque: 39 N.m (400 kgf.cm, 29 ft.lbf) 

    Fig 4: Removing Starter Set Bolt
    G02906336Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. ATTACH ENGINE SLING DEVICE TO ENGINE HANGER 
    1. Remove the bolt.
      Fig 5: Removing Bolt
      G02906337Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the 2 No. 1 engine hangers with the bolts in the correct direction.

      Parts No.: 

      No. 1 engine hanger: 12281-21010 

      Bolt: 91642-81025 

      Torque: 40 N.m (400 kgf.cm, 29 ft.lbf) 

    3. Attach the engine chain hoist to the engine hangers.
      CAUTION: Do not attempt to hang the engine by hooking the chain to any other part.
      Fig 6: Installing Engine Hangers
      G02906338Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. RAISE VEHICLE 
    CAUTION: Make sure that the vehicle is securely supported.
  15. REMOVE LH ENGINE UNDER COVER 
  16. DRAIN TRANSAXLE OIL 

    Oil grade: API GL-4 or GL-5 

    Viscosity: SAE 75 W-90 

    Capacity: 1.9 liters (2.0 US qts, 1.7 lmp. qts) 

    Torque: 39 N.m (400 kgf.cm, 29 ft.lbf) 

  17. REMOVE RH AND LH FRONT DRIVE SHAFTS (See  REMOVAL & INSTALLATION  ) 
    Fig 7: Locating Filler Plug
    G02906339Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE SUSPENSION MEMBER 
    1. Remove the 2 set nuts and bolt of the engine rear mounting insulator from the suspension member (See REMOVAL & INSTALLATION ).
    2. Disconnect the sliding yoke (See REMOVAL ).
    3. Power steering:

      Disconnect the pressure feed and return tubes (See REMOVAL ).

    4. Power steering:

      Disconnect the tube clamp (See REMOVAL ).

    5. Remove the suspension member (See REMOVAL & INSTALLATION ).
  19. JACK UP TRANSAXLE SLIGHTLY 

    Using a transmission jack, support the transaxle.

  20. DISCONNECT ENGINE LEFT MOUNTING BRACKET FROM ENGINE LEFT MOUNTING INSULATOR 

    Remove the 2 bolts.

    Torque: 49 N.m (500 kgf.cm, 36 ft.lbf) 

    Fig 8: Removing Engine Left Mounting Bracket
    G02906340Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. REMOVE ENGINE REAR MOUNTING INSULATOR AND BRACKET 
    1. Remove the bolt, nut and engine rear mounting insulator.

      Torque: 64 N.m (650 kgf.cm, 47 ft.lbf) 

    2. Remove the 3 bolts and engine rear mounting bracket.

      Torque: 49 N.m (500 kgf.cm, 36 ft.lbf) 

      Fig 9: Removing Engine Rear Mounting Insulator And Bracket
      G02906341Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. REMOVE STARTER 
    1. Remove the bolt, starter cover and starter.

      Torque: 39 N.m (400 kgf.cm, 29 ft.lbf) 

    2. Disconnect the starter connector.
    3. Remove the nut and starter wire.
      Fig 10: Removing Starter
      G02906342Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  23. REMOVE 5 TRANSAXLE LOWER SIDE MOUNTING BOLTS 

    Torque: 33 N.m (340 kgf.cm, 25 ft.lbf) 

  24. REMOVE TRANSAXLE 

    Lower the engine left side and remove the transaxle from the engine.

    HINT:

    At the time of installation, please refer to the following items  1.

    • Align the input shaft with the clutch disc and install the transaxle to the engine.
    • Temporarily tighten the transaxle mounting bolts.
      Fig 11: Removing Transaxle Lower Side Mounting Bolts
      G02906343Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002