LEMON Manuals: Even more car manuals for everyone

Manual Transaxle Assembly: Inspection

  1. INSPECT 5TH GEAR SYNCHRONIZER RING 
    1. Check for wear or damage.
    2. Check the braking effect of the synchronizer ring. Turn the synchronizer ring in one direction while pushing it to the gear cone. Check that the ring locks.

      If the braking effect is insufficient, apply a small amount of the fine lapping compound between the synchronizer ring and gear cone. Lightly rub the synchronizer ring and gear cone together.

      NOTE: Ensure the fine lapping compound is completely washed off after rubbing.
    3. Check again the braking effect of the synchronizer ring.
      Fig 1: Checking Braking Effect Of Synchronizer Ring
      G02906368Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Using a feeler gauge, measure the clearance between the synchronizer ring back and gear spline end.

      Minimum clearance: 0.75 mm (0.0295 in.) 

      If the clearance is less than the minimum, replace the synchronizer ring and gear cone by applying a small amount of the fine lapping compound.

      NOTE: Ensure the fine lapping compound is completely washed off after rubbing.
      Fig 2: Measuring Clearance Between Synchronizer Ring Back And Gear Spline End
      G02906369Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSPECT SHIFT FORK AND HUB SLEEVE CLEARANCE 

    Using a feeler gauge, measure the clearance between the hub sleeve and shift fork.

    Maximum clearance: 0.5 mm (0.020 in.) 

    If the clearance exceeds the maximum, replace the shift fork or hub sleeve.

  3. REMOVE TRANSAXLE CASE RECEIVER 

    Remove the bolt and transaxle case receiver.

    Fig 3: Measuring Clearance Between Hub Sleeve And Shift Fork
    G02906370Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. IF NECESSARY, REPLACE INPUT SHAFT FRONT BEARING AND OIL SEAL 
    1. Using SST, remove the input shaft front bearing.

      SST 09612-65014

      Fig 4: Removing Input Shaft Front Bearing
      G02906371Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using SST, remove the oil seal.

      SST 09612-65014

      Fig 5: Removing Oil Seal
      G02906372Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using SST and a hammer, install a new oil seal.

      SST 09950-60010 (09951 - 00360), 09950- 70010 (09951 -07150)

      Drive in depth: 15.8 +/- 0.2 mm (0.622 +/- 0.008 in.)

    4. Coat the lip of the oil seal with MP grease.
      Fig 6: Installing Oil Seal
      G02906373Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Using SST and a press, install a new input shaft front bearing.

      SST 09950-60010 (09951-00460), 09950-70010 (09951-07150)

      Fig 7: Installing Input Shaft Front Bearing
      G02906374Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. IF NECESSARY, REPLACE OUTPUT SHAFT FRONT BEARING AND OUTPUT SHAFT COVER 
    1. Remove the bolt and bearing lock plate.
      Fig 8: Removing Bolt And Bearing Lock Plate
      G02906375Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using SST, pull out the output shaft front bearing.

      SST 09308-00010

      Fig 9: Pulling Out Output Shaft Front Bearing
      G02906376Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the output shaft cover.
    4. Install the output shaft cover.
      NOTE: Install the output shaft cover projection into the case side hollow.
      Fig 10: Removing Output Shaft Cover
      G02906377Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Using SST and a press, install a new output shaft front bearing.

      SST 09950-60010 (09951-00620), 09950-70010 (09951-07150)

    6. Install the bearing lock plate with the bolt.

      Torque: 11 N.m (115 kgf.cm, 8 ft.lbf) 

  6. INSTALL TRANSAXLE CASE RECEIVER 

    Install the transaxle case receiver with the bolt.

    Torque: 11 N.m (115 kgf.cm, 8 ft.lbf) 

    Fig 11: Installing Output Shaft Front Bearing
    G02906378Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. IF NECESSARY, REPLACE REVERSE RESTRICT PIN 
    1. Using a hexagon wrench, remove the straight screw plug.
    2. Using a pin punch and hammer, drive out the slotted spring pin.
      Fig 12: Driving Out Slotted Spring Pin
      G02906379Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Replace the reverse restrict pin.
    4. Using a pin punch and hammer, drive in the slotted spring pin.
    5. Apply sealant to the plug threads.

      Sealant: 

      Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent 

    6. Using a hexagon wrench, install the straight screw plug.

      Torque: 13 N.m (130 kgf.cm, 9 ft.lbf) 

      Fig 13: Installing Straight Screw Plug
      G02906380Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002