LEMON Manuals: Even more car manuals for everyone

Power Steering Gear: Installation

  1. INSTALL ENGINE REAR MOUNT INSULATOR AND ENGINE REAR MOUNT BRACKET 
    1. Install the engine rear mount bracket with the 3 bolts.

      Torque:  49 N.m (500 kgf.cm, 36 ft.lbf)

    2. Install the engine rear mount insulator with the through bolt and No. 2 engine rear mount bracket.

      Torque:  64 N.m (650 kgf.cm, 47 ft.lbf)

  2. INSTALL PS GEAR ASSEMBLY 
    1. Align the matchmarks on the No. 3 intermediate shaft assembly and control valve shaft.
      Fig 1: Aligning Matchmarks On No. 3 Intermediate Shaft Assembly & Control Valve Shaft
      G02906715Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the No. 3 intermediate shaft assembly with the bolt.

      Torque:  28 N.m (290 kgf.cm, 21 ft.lbf)

    3. Install the grommet and bracket to the PS gear assembly.

      HINT:

      Install the bracket with the inscribed mark facing to the front of the vehicle.

      Fig 2: Identifying Bracket Inscribed Mark Installation Position
      G02906716Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install the PS gear assembly with the 4 bolts and nuts to the front suspension member.

      Torque:  74 N.m (750 kgf.cm, 54 ft.lbf)

      Fig 3: Installing PS Gear Assembly
      G02906717Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE: Because the nut has its own stopper, do not turn the nut and torque the bolt with the nut fixed. 
    5. Install the column hole cover sub-assembly.
    6. Install the dynamic damper and rack housing heat insulator with the 2 bolts as shown in Fig 4 .

      Torque:  18 N.m (180 kgf.cm, 13 ft.lbf)

      Fig 4: Installing Rack Housing Heat Insulator Bolt
      G02906718Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Install the bolt of the rack housing heat insulator.

      Torque:  35 N.m (360 kgf.cm, 26 ft.lbf)

    8. Install the stabilizer bar (See REMOVAL & INSTALLATION ).
  3. INSTALL FRONT SUSPENSION MEMBER WITH LOWER SUSPENSION ARM AND PS GEAR ASSEMBLY 
    1. Using SST, align the holes of the front suspension member and body.

      SST 09670-00010

      Fig 5: Installing Front Suspension Member With Lower Suspension Arm & PS Gear Assembly
      G02906720Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Employ the same manner described above to the other side.
      Fig 6: Aligning Front Suspension Member & Body Holes
      G02906719Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install the front suspension member with lower suspension arm and PS gear assembly with the 4 bolts.

      Torque: 

      1. Bolt A:  116 N.m (1,180 kgf.cm, 85 ft.lbf)
      2. Bolt B:  70 N.m (715 kgf.cm, 52 ft.lbf)
  4. CONNECT ENGINE REAR MOUNT INSULATOR AND FRONT SUSPENSION MEMBER 

    Connect the engine rear mount insulator and front suspension member with the bolt and 2 nuts.

    Torque:  80 N.m (810 kgf.cm, 59 ft.lbf)

    Fig 7: Connecting Engine Rear Mount Insulator & Front Suspension Member
    G02906721Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. CONNECT LOWER SUSPENSION ARM TO STEERING KNUCKLE (SEE  REMOVAL & INSTALLATION  ) 
  6. DISENGAGE ENGINE SLING DEVICE FROM ENGINE HANGERS 
    1. Disengage the engine chain hoist from the engine hangers.
    2. Remove the 2 No. 1 engine hangers.
  7. INSTALL ENGINE HOOD (SEE  ADJUSTMENT  ) 
  8. CONNECT TUBE CLAMP 
    1. Temporarily connect the pressure feed and return tubes.
    2. Connect the tube clamp with the bolt.

      Torque:  7.8 N.m (80 kgf.cm, 69 in.lbf)

      Fig 8: Connecting Tube Clamp
      G02906722Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. CONNECT PRESSURE FEED AND RETURN TUBES 
    1. Using SST, connect the pressure feed and return tubes.

      SST 09023-12900

      Torque:  27 N.m (280 kgf.cm, 20 ft.lbf)

      Fig 9: Connecting Pressure Feed & Return Tubes
      G02906723Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT:

      • Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
      • This torque value is effective in case that SST is parallel to a torque wrench.
    2. Connect the return hose with the clip.
    3. Connect the column hole cover sub-assembly.
  10. CONNECT SLIDING YOKE (SEE  INSTALLATION   ) 
  11. INSTALL NO. 2 COLUMN HOLE COVER 

    (SEE  INSTALLATION   ) 

  12. CONNECT RH AND LH TIE ROD ENDS 

    (SEE  INSTALLATION  ) 

  13. INSTALL RH AND LH ENGINE UNDER COVERS 
  14. PLACE FRONT WHEELS FACING STRAIGHT AHEAD 

    HINT:

    Do it with the front of the vehicle jacked up.

  15. CENTER SPIRAL CABLE (SEE  INSTALLATION   ) 
  16. INSTALL STEERING WHEEL 
    1. Align the matchmarks on the steering wheel and steering column main shaft.
    2. Temporarily tighten the steering wheel set nut.
  17. BLEED POWER STEERING SYSTEM 

    ((SEE  BLEEDING   ) 

  18. CHECK STEERING WHEEL CENTER POINT 
  19. TORQUE STEERING WHEEL SET NUT 

    Torque:  50 N.m (510 kgf.cm, 37 ft.lbf)

  20. INSTALL STEERING WHEEL PAD (SEE  INSTALLATION   ) 
  21. CHECK FRONT WHEEL ALIGNMENT 

    (SEE  INSPECTION  )