LEMON Manuals: Even more car manuals for everyone

Engine Unit (Removal & Installation): Removal

  1. REMOVE ENGINE UNDER COVERS 
  2. DRAIN TRANSAXLE OIL 
  3. DRAIN TRANSFER OIL 
  4. DRAIN ENGINE OIL 
  5. DRAIN ENGINE COOLANT 
  6. REMOVE HOOD 
  7. REMOVE RADIATOR RESERVOIR 
  8. REMOVE BATTERY AND TRAY 
    1. Remove the cowl top ventilation louver (See REMOVAL )
    2. Remove the hold-down clamp, battery and tray.
    3. Remove the 5 bolts and battery bracket.
      Fig 1: Removing Bolts & Battery Bracket
      G02854102Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE AIR CLEANER ASSEMBLY 
    Fig 2: Removing Air Cleaner Assembly
    G02854103Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the MAF meter connector.
    2. Disconnect the 2 EVAP hoses from the VSV.
    3. Disconnect VSV connector for EVAP.
    4. Disconnect the CCV hose from the air cleaner.
    5. Disconnect the PCV hose from the cylinder head cover.
    6. Disconnect the air cleaner hose from the throttle body, and remove the 3 bolts and the air cleaner assembly.
  10. REMOVE ENGINE ROOM J/B 
    1. Remove the engine room J/B cover.
    2. Fig 3: Removing Engine Room J/B
      G02854104Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Loosen the bolt.
    4. Remove the engine room J/B.
    5. Pull out the engine wire connector.
    6. Disconnect the connector.
    7. Disconnect the engine wire clamp.
  11. DISCONNECT ENGINE WIRE FROM CABIN 
    1. Remove the 2 screws and glove compartment door.
    2. Disconnect the 6 engine wire connectors from the ECM and instrument panel wire.
    3. Pull out the engine wire from the cabin.
  12. DISCONNECT TUBES, HOSES, CONNECTOR, CABLE AND WIRE 
    1. Disconnect the accelerator cable.
    2. Disconnect the ground wire from the cylinder head.
    3. Disconnect the discharge and liquid tubes from the compressor, and remove the 2 O-rings (See REMOVAL )
      Fig 4: Disconnecting Discharge And Liquid Tubes From Compressor
      G02854105Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Disconnect the suction hose, pressure feed tube and gasket from the PS vane pump.
    5. Fig 5: Disconnecting Suction Hose, Pressure Feed Tube & Gasket From PS Vane Pump
      G02854106Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Disconnect the upper radiator hose.
    7. Disconnect the lower radiator hose.
    8. Disconnect the fuel tube connector (See SERVICE PRECAUTIONS ).
    9. Disconnect the 2 heater hoses.
    10. Disconnect the connector from the fusible link block.
    Fig 6: Disconnecting Connector From Fusible Link Block
    G02854107Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. M/T: 

    DISCONNECT SHIFT CONTROL CABLES FROM TRANSAXLE 

    1. Remove the 2 clips and 2 washers.
    2. Remove the 2 clips, and disconnect the 2 control cables.
      Fig 7: Disconnecting Shift Control Cables From Transaxle (M/T)
      G02854108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE STARTER 
    1. A/T:

      Disconnect the hose from the dipstick guide.

    2. Disconnect the connector.
    3. Remove the 2 bolts, and disconnect the starter.
    4. Remove the nut, and disconnect the starter cable.
    5. Remove the starter.
      Fig 8: Removing Starter
      G02854109Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. M/T: 

    DISCONNECT CLUTCH RELEASE CYLINDER AND LINE FROM TRANSAXLE 

    1. Remove the 2 bolts and heat insulator.
    2. Remove the 5 bolts, and disconnect the release cylinder.
      Fig 9: Disconnecting Clutch Release Cylinder & Line From Transaxle (M/T)
      G02854110Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. A/T: 

    DISCONNECT SHIFT CONTROL CABLE FROM TRANSAXLE 

    1. Remove the nut holding the control shift lever to the control cable.
    2. Fig 10: Disconnecting Shift Control Cable From Transaxle (A/T)
      G02854111Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the clip, and disconnect the control cable.
    4. Disconnect the control cable from the cable clamp.
  17. A/T: 

    DISCONNECT OIL COOLER HOSES 

    Fig 11: Disconnecting Oil Cooler Hoses (A/T)
    G02854112Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. DISCONNECT GROUND CABLE FROM TRANSAXLE 
  19. 4WD: 

    REMOVE PROPELLER SHAFT (See  REMOVAL  ) 

  20. REMOVE FRONT DRIVE SHAFTS (See  REMOVAL & INSTALLATION  ) 
  21. REMOVE FRONT EXHAUST PIPE 
    Fig 12: Removing Front Exhaust Pipe
    G02854113Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Remove the 4 bolts, 2 compression rings, 2 gaskets and exhaust pipe.

  22. DISCONNECT STABILIZER BAR LINKS 

    Remove the 2 nuts, and disconnect the LH and RH stabilizer links.

    Fig 13: Disconnecting Stabilizer Bar Links
    G02854114Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  23. DISCONNECT PS GEAR ASSEMBLY 

    Remove the 2 bolts of the PS gear assembly.

    Fig 14: Disconnecting PS Gear Assembly
    G02854115Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  24. ATTACH ENGINE SLING DEVICE TO ENGINE HANGERS 
    1. Install No. 1 and No. 2 engine hangers in the correct direction.
      ENGINE HANGERS SPECIFICATIONS

      Item Part No.
      No. 1 And No. 2 Engine Hangars 12281-28010, 12281-28020 or 12281-28030
      Bolt 91512-61020 x 2
      1. Torque: 38 N.m (390 kgf.cm, 28 ft.lbf) 
    2. Attach the sling device to the engine hangers.
    3. Fig 15: Attaching Engine Sling Device To Engine Hangers
      G02854116Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    CAUTION: Do not attempt to hang the engine by hooking the chain to any other part.
  25. REMOVE ENGINE, TRANSAXLE, FRONT SUSPENSION CROSSMEMBER AND CENTER ENGINE MOUNTING MEMBER ASSEMBLY 
    1. Remove the 2 nuts and bolt holding the RH engine mounting insulator to the timing chain cover.
      Fig 16: Removing RH Engine Mounting Insulator To Timing Chain Cover Bolts
      G02854117Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt holding the LH engine mounting insulator to the mounting bracket.
      Fig 17: Removing LH Engine Mounting Insulator To Mounting Bracket Bolt
      G02854118Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Support the suspension crossmember with a jack.
    4. Remove the 6 bolts holding the suspension crossmember engine mounting member to the body.
      Fig 18: Removing Suspension Crossmember Engine Mounting Member To Body Bolts
      G02854119Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Lower the engine out of the vehicle slowly and carefully.
    6. Fig 19: Lowering Engine Out Of Vehicle
      G02854120Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    NOTE: Make sure the engine is clear of all wiring, hoses and cables.
  26. REMOVE ENGINE AND TRANSAXLE ASSEMBLY FROM FRONT SUSPENSION CROSSMEMBER AND CENTER ENGINE MOUNTING MEMBER 
    1. Remove the bolt holding the front engine mounting bracket to the mounting insulator.
      Fig 20: Removing Front Engine Mounting Bracket To Mounting Insulator Bolt
      G02854121Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt holding the rear engine mounting bracket to the mounting insulator.
    3. Fig 21: Removing Rear Engine Mounting Bracket To Mounting Insulator Bolt
      G02854122Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Separate the engine and transaxle assembly from the suspension crossmember and engine mounting member.
  27. 4WD: 

    REMOVE STIFFENER PLATE 

    Remove the 5 bolts and stiffener plate.

    Fig 22: Removing Bolts & Stiffener Plate
    G02854123Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. 2WD: 

    REMOVE CENTER BEARING BRACKET 

    Remove the 3 bolts and bearing bracket.

    Fig 23: Removing Bolts & Bearing Bracket (2WD)
    G02854124Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. A/T: 

    REMOVE TORQUE CONVERTER CLUTCH BOLTS 

    1. Remove the hole plug.
    2. Turn the crankshaft to gain access to each bolt.
    3. Hold the crankshaft pulley bolt with a wrench, and remove the 6 bolts.
      Fig 24: Removing Torque Converter Clutch Bolts (A/T)
      G02854125Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  30. REMOVE TRANSAXLE FROM ENGINE 
    1. Remove the 4 lower bolts holding the engine to the transaxle.
      Fig 25: Removing Bolts Holding Engine To Transaxle
      G02854126Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. M/T:

      Disconnect the connectors.

      1. Disconnect the vehicle speed sensor connector.
      2. Disconnect the back-up light switch connector.
        Fig 26: Disconnecting Connectors (M/T)
        G02854127Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. A/T:

      Disconnect the connectors and clamps.

      Fig 27: Disconnecting Connectors & Clamps
      G02854128Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disconnect the park/neutral position switch connector.
      2. Disconnect the solenoid wire connector.
      3. Disconnect the input turbine speed sensor connector.
      4. Disconnect the counter gear speed sensor connector.
      5. Disconnect the vehicle speed sensor.
      6. Disconnect the wire clamp from the bracket.
      7. Disconnect the wire clamp from the engine mounting bracket.
    4. Remove the 6 upper bolts holding the transaxle to the engine.
    5. Fig 28: Removing Upper Bolts Holding Transaxle To Engine
      G02854129Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Remove the transaxle together with the torque converter clutch (A/T) from the engine.
  31. REMOVE DRIVE BELT (See  REMOVAL & INSTALLATION  ) 
  32. M/T: 

    REMOVE CLUTCH COVER, DISC AND FLYWHEEL 

  33. A/T: 

    REMOVE DRIVE PLATE 

  34. REMOVE A/C COMPRESSOR 
    Fig 29: Removing Bolts, Nut & Compressor
    G02854130Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the magnetic clutch and lock sensor connector from the compressor.
    2. Remove the 3 bolts, nut and compressor.
  35. REMOVE PS VANE PUMP 
    Fig 30: Removing PS Vane Pump
    G02854131Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the oil pressure switch connector.
    2. Remove the 2 bolts and vane pump.
  36. REMOVE GENERATOR 
    Fig 31: Removing Generator
    G02854132Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the terminal cover and nut, and disconnect the generator wire.
    2. Disconnect the generator connector.
    3. Disconnect the A/C wire.
    4. Remove the 2 bolts and generator.