Chain Cover: Removal
NOTE:
When replacing a single part, perform the work with the engine assembly installed to body.
- When working on the vehicleNOTE: When working on the vehicle, perform the following steps also.
- Remove the intercooler. Ref. to INTAKE (INDUCTION) (EXCEPT FOR STI)>Intercooler>REMOVAL .
- Remove the intake duct No. 1 and intake duct No. 2. Ref. to INTAKE (INDUCTION) (EXCEPT FOR STI)>Intake Duct>REMOVAL>INTAKE DUCT NO. 1 . Ref. to INTAKE (INDUCTION) (EXCEPT FOR STI)>Intake Duct>REMOVAL>INTAKE DUCT NO. 2 .
- Remove the radiator. Ref. to COOLING(EXCEPT FOR STI)>Radiator>REMOVAL .
- Remove the front exhaust pipe. Ref. to EXHAUST(EXCEPT FOR STI)>Front Exhaust Pipe>REMOVAL .
- Drain the engine oil. Ref. to LUBRICATION(EXCEPT FOR STI)>Engine Oil>REPLACEMENT .
- Remove the V-belts. Ref. to MECHANICAL(EXCEPT FOR STI)>V-belt>REMOVAL>V-BELT .
- Remove the generator. Ref. to STARTING/CHARGING SYSTEMS(EXCEPT FOR STI)>Generator>REMOVAL .
- Remove the water pump pulley. Ref. to COOLING(EXCEPT FOR STI)>Water Pump>REMOVAL>WATER PUMP .
- Remove the crank pulley. Ref. to MECHANICAL(EXCEPT FOR STI)>Crank Pulley>REMOVAL .
- Remove the engine oil cooler. Ref. to LUBRICATION(EXCEPT FOR STI)>Engine Oil Cooler>REMOVAL .
- Remove the front engine oil cooler pipe assembly. Ref. to LUBRICATION(EXCEPT FOR STI)>Engine Oil Cooler Pipe>REMOVAL>FRONT ENGINE OIL COOLER PIPE .
- Remove the clip securing the PCV pipe to the intake manifold.
- Remove the PCV pipe from the clip (A), and place the PCV pipe aside so that it does not interfere with the work.
- Disconnect the connector from the engine wiring harness.
- Remove the connector (A) and connector (B) from the vacuum pipe assembly.
- Disconnect the vacuum control hose (C) and vacuum hose (D) from the vacuum pipe assembly, and remove the vacuum pipe assembly from the chain cover.
- Disconnect the connector (A) from the intake oil control solenoid RH, connector (B) from the exhaust oil control solenoid RH, connector (C) from the intake camshaft position sensor RH, and the connector (D) from the exhaust camshaft position sensor RH, and then remove the clips (E) and (F) securing the engine wiring harness.
- Disconnect the connector (A) from the exhaust camshaft position sensor LH and the connector (B) from the oil level switch, and remove the engine wiring harness stay from the chain cover.
- Remove the rubber cap from the oil pressure switch.
- Disconnect the terminal (A) from the oil pressure switch, connector (B) from the engine oil temperature sensor, connector (C) from the intake oil control solenoid LH, connector (D) from the exhaust oil control solenoid LH, and the connector (E) from the intake camshaft position sensor LH, and then remove the clip (F) securing the engine wiring harness.
- Pull out the oil level gauge (A), and remove the oil level gauge guide (B), crank pulley boss (C), and idler pulley (D).
- Remove the bolts securing the chain cover to engine.
- Pry the points shown in the figure with a crowbar wrapped by protective tape, and then remove the chain cover from the engine.CAUTION: The chain cover may contact the protrusion (a) of cam sprocket sensor plate and cause damage. When removing the chain cover, move the chain cover horizontally until it cannot contact with the cam sprocket, and then remove it carefully.
- Remove the O-rings from cylinder head RH, cylinder head LH, cylinder block LH and oil pan upper.
- Remove the liquid gasket from the chain cover and engine unit.
- Remove the front oil seal from the chain cover.