LEMON Manuals: Even more car manuals for everyone

Clutch Pedal: Adjustment

WARNING: This page is about a different variant/trim than selected.
  1. Measure the full stroke of the clutch pedal.
    NOTE:
    • Measure the leading end of the seat cushion and center of the pedal.
    • Align the seat with the seventh notch position from the position at the very front.

    Specified clutch pedal full stroke A: 

    5MT non-turbo model and 6MT model: 

    130 - 135 mm (5.12 - 5.31 in) 

    5MT turbo model: 

    135 - 140 mm (5.31 - 5.51 in) 

    Fig 1: Identifying Clutch Pedal Full Stroke
    G05669771Courtesy of SUBARU OF AMERICA, INC.
  2. If the full stroke is not within the specified value, loosen the clutch switch lock nut to adjust.

    Tightening torque: 

    8 N.m (0.8 kgf-m, 5.8 ft-lb) 

  3. Loosen the push rod lock nuts.
    Fig 2: Identifying Snap Pin, Clevis Pin, Push Rod And Lock Nut
    G05669772Courtesy of SUBARU OF AMERICA, INC.
  4. Rotate the push rod to adjust.
    1. Make sure that the clutch pedal contacts the clutch switch side when the pedal is released.
    2. Make sure that the clutch pedal contacts the clutch pedal bracket stopper when the clutch pedal is at the maximum stroke position.
      Fig 3: Rotating Push Rod
      G05669773Courtesy of SUBARU OF AMERICA, INC.
  5. Turn the push rod to shorten until a clearance is gained on the clutch switch side.
    Fig 4: Identifying Clearance Between Clutch Switch And Stopper
    G05669774Courtesy of SUBARU OF AMERICA, INC.
  6. Turn the push rod to lengthen until clutch pedal contacts the clutch switch.
  7. Turn further in the direction that will shorten the push rod (arrow direction shown in figure) by 270°.
    Fig 5: Turning Push Rod
    G05669775Courtesy of SUBARU OF AMERICA, INC.
  8. Check that the clevis pin moves smoothly by moving it in the left and right directions.
  9. Tighten the push rod lock nut.

    Tightening torque: 

    10 N.m (1.0 kgf-m, 7.2 ft-lb) 

  10. Depress and release the clutch pedal two or three times to ensure that the clutch pedal and release fork operate smoothly. If the clutch pedal and release fork do not operate smoothly, bleed air from the clutch hydraulic system. < Ref. to CLUTCH FLUID AIR BLEEDING . >
  11. Measure the clutch pedal full stroke length again to ensure that it is within specifications. If it is not within specifications, repeat adjustment procedures again from the beginning.

    Specified clutch pedal full stroke: 

    5MT non-turbo model and 6MT model: 

    130 - 135 mm (5.12 - 5.31 in) 

    5MT turbo model: 

    135 - 140 mm (5.31 - 5.51 in) 

  12. Move the clevis pin to left, then to right. The clevis pin should move without resistance even if it is rattling. If resistance is felt, repeat adjustment procedures again from the beginning.
  13. Push the release lever until the operating cylinder push rod retracts. Make sure that the clutch fluid level in the reservoir tank increases. If the clutch fluid level increases, the hydraulic clutch is properly adjusted; if the fluid level does not increase or the push rod does not retract, replace the master cylinder. < Ref. to MASTER CYLINDER . >
    • 5MT model
      NOTE: The illustration below is for a Non-turbo model. However, perform the same procedures for the Turbo model.
      Fig 6: Identifying Operating Cylinder, Push Rod And Release Lever (5MT Model)
      G05669776Courtesy of SUBARU OF AMERICA, INC.
    • 6MT model
      Fig 7: Identifying Operating Cylinder, Push Rod And Release Lever (6MT Model)
      G05669777Courtesy of SUBARU OF AMERICA, INC.
  14. Check the fluid level using the scale on the outside of the reservoir tank. If the level is below "MIN", fill fluid up to "MAX" level.

    Recommended clutch fluid: 

    FMVSS No. 116, fresh DOT3 or 4 brake fluid 

    Fig 8: Identifying Clutch Fluid Level
    G05669778Courtesy of SUBARU OF AMERICA, INC.