LEMON Manuals: Even more car manuals for everyone

Engine Cooling System Flush And Refill (WWY-09)

WARNING: This page is about the Outback Limited, 4D Sedan, Automatic, which is a different variant/trim than selected.
Publication date: 2006-06-01
Reference number: WWY-09

ENGINE COOLING SYSTEM FLUSH AND REFILL

ENGINE COOLING SYSTEM FLUSH AND REFILL

SERVICE CAMPAIGN BULLETIN

Reference Number(s): WWY-09, Date of Issue:  June 01, 2006
SUBARU: 2006 BAJA, Legacy, Outback and B-9 Tribeca

INTRODUCTION

Subaru of America, Inc. (SOA) has determined that vehicles affected by this Service Program require the engine cooling system to be drained, thoroughly flushed and refilled with new engine coolant. During a quality review, it was discovered that the coolant mixture used during production may contain a high level of chlorine. With a high chlorine content, the coolant can adversely react with aluminum components and quickly cause premature corrosion to occur within the cooling system. If left uncorrected, this condition will diminish the effectiveness of the heater core resulting in poor performance.

This service program will involve thoroughly flushing & refilling the engine cooling system.

AFFECTED VEHICLES

Affected vehicles are identified in the VIN range chart below.

NOTE: Not all vehicles found within the VIN range are affected. Prior to performing repairs, confirm coverage for potentially affected vehicles by using the Vehicle Coverage Inquiry in the Dealer Communication System (DCS).
VEHICLE INFORMATION

MODEL FROM TO
Baja  2006MY   6(1)100778 6(1)100968
Legacy  2006MY Sedan 6(1)203134 6(1)203905
Wagon 6(1)308237 6(1)310594
Outback  2006MY Sedan 6(1)202134 6(1)203890
Wagon 6(1)308219 6(1)310619
B9 Tribeca  2006MY   6(1)410669 6(1)412625
(1) Various characters may occupy this position of the VIN.

OWNER NOTIFICATION

SOA will prepare and mail an Owner Notification Letter to owners of affected vehicles on or around June 14, 2006.

A copy of the Owner Notification Letter is included at the end of this bulletin.

DEALER PROGRAM RESPONSIBILITY

Dealers are to promptly service all vehicles subject to this service program at no charge to the vehicle owner regardless of mileage, age of the vehicle, or ownership.

For affected vehicles sold after the date on the dealer's computer list, dealers are to contact those owners and provide them with a copy of the owner notification letter. They should also arrange to make the required correction according to the instructions in the service procedure section of this bulletin.

Dealers are also to promptly perform the applicable service procedures defined in this bulletin to correct all affected vehicles in their inventory (new, used, demo). Additionally, whenever a vehicle subject to this service program is taken into dealer new or used inventory, or is in the dealership for service, necessary steps should be taken to ensure the service program correction has been made before selling or releasing the vehicle.

PARTS INFORMATION

Subaru Engine Coolant 

NOTE: Genuine Subaru Factory Fill Long Life Coolant is packaged in cases that contain six (6) one (1) gallon containers. Each affected vehicle requires a one (1) gallon container. This part number must be ordered through the Genuine Subaru Chemicals Program.
PARTS INFORMATION

MODEL DESCRIPTION PART NUMBER
All Genuine Subaru Factory Fill Long Life Coolant SOA868V9210

Subaru Cooling System Conditioner 

NOTE: Subaru Cooling System Conditioner is packaged in cases that contain 12 bottles. Each affected vehicle requires one (1) bottle. This part number must be ordered through normal parts channels.
PARTS INFORMATION

MODEL DESCRIPTION PART NUMBER
All Subaru Cooling System Conditioner Case SOA345001

SPECIAL TOOLS

Special Equipment Needed: 5/8" Garden Hose (25-50 feet), 1 (5/8") Hose coupler, 2 (5/8") Hose Clamps

Fig 1: Special Tools
G06146422

SERVICE PROCEDURE

CAUTION: The engine cooling system is under pressure and may be extremely hot. To prevent personal injury or vehicle damage, be sure to take appropriate precautions while preforming the following procedures.

Completing the following coolant flush procedure has been confirmed to effectively clean and remove any contaminates or corrosion, as well as eliminate the chlorine from the cooling system. A flush machine or flushing agents/chemicals must NOT  be used in this procedure.

NOTE: The following procedure should be performed at or near a water source (i.e., garden hose) which should be free of contamination from sediment, chlorine and sulfides.

Coolant Flush Procedure

NOTE: All drained and flushed coolant should be recycled or disposed of in accordance with applicable Federal/State/Local/Environmental Protection regulations.
  1. Drain Engine Coolant
    • Remove the Radiator Cap and Reservoir Tank. (Use extreme caution when removing the radiator cap.)
    • Raise the vehicle.
    • Remove the engine under cover.
    • Remove the drain plug to drain the engine coolant.
      NOTE: While coolant is draining, wash out the reservoir tank. Fill the tank about 1/3 of the way with water and shake vigorously. If needed, use a soap solution to ensure all sediment is removed.
    • When coolant is fully drained, reinstall the drain plug in the radiator.
    Fig 2: Locating Drain Plug - H4 SDHC
    G06146423
    Fig 3: Locating Drain Plug - H4 Turbo
    G06146424
    Fig 4: Locating Drain Plug - H6 (Except For B9 Tribeca)
    G06146425
    Fig 5: Locating Drain Plug - B9 Tribeca
    G06146426
  2. Create a heater core bypass loop
    • Remove Engine top cover (All except H4 SOHC).
    • Remove both coolant hoses from the heater core.
    • Using a hose connector (5/8" x 5/8"), connect the two heater hoses, creating a heater core bypass loop.
    Fig 6: Connecting Hose Connector
    G06146427
    Fig 7: Connecting Two Heater Hoses
    G06146428
    Fig 8: Hose Connector
    G06146429
  3. Fill cooling system with water
    • Pour water into the radiator up to the filler neck.
    • Install the radiator cap.
  4. Flush the heater core (at least 4 times)
    • Move the vehicle to a water supply if away from one.
    • Install garden hose from water supply to heater core (upper inlet).
    • Install garden hose on lower heater core tube for draining.
      Fig 9: Water Supply To Heater Core (Upper Inlet)
      G06146430
      Fig 10: Upper & Lower Heater Core Tube
      G06146431
    • Flush the heater core using a pail (at least 4 times).
      Fig 11: Flushing Heater Core Using Pail (1 Of 2)
      G06146432
      Fig 12: Flushing Heater Core Using Pail (2 Of 2)
      G06146433
    • Remove both garden hoses from the heater core.
  5. Water flushing of the cooling system
    • Warm up the engine completely for more than five minutes at 2,000 to 3,000 RPM.
  6. Drain flushing water
    • Raise the vehicle on a lift.
    • Drain flushing water from the cooling system.
    • Reinstall the engine under cover.
  7. Restore cooling system
    • Remove hose connector from the heater bypass loop.
    • Connect heater hoses to the original positions.
    • Reinstall the reservoir tank.
    • Reinstall the engine top cover (All except H4 SOHC).
  8. Fill the engine coolant
NOTE: Add Subaru Cooling System Conditioner through the filler neck of the radiator prior to adding coolant and water.
COOLING SYSTEM CONDITIONER INFORMATION

H4 (SOHC) H4 (TURBO) H6 (Except B9 Tribeca)
  1. Pour cooling system conditioner through the filler neck. (Do NOT add conditioner to the overflow bottle) Cooling System Conditioner (Part No. SOA635071)
  2. Pour engine coolant into the radiator up to the filler neck level. Coolant Capacity (Fill up to "Full" level): MT Model: 6.8 US qt. (5.6 Imp qt.) AT Model: 6.7 US qt. (5.5 Imp qt.)
    NOTE: The SUBARU Genuine Coolant containing antifreeze and anti-rust agents is especially made for the SUBARU engine, which has an aluminum crankcase. Always use SUBARU Genuine Coolant, since other coolant may cause corrosion.
  3. Fill engine coolant into the reservoir tank up to "FULL" level.
  4. Warm up the engine completely for more than five minutes at 2,000 to 3,000 RPM.
  5. If the engine coolant level drops in radiator, add engine coolant at the filler neck.
  6. If the engine coolant level drops from "FULL" level of reservoir tank, add engine coolant to "FULL" level.
  7. Reinstall the radiator cap and reservoir tank cap properly.
  1. Remove the collector cover.
  2. Pour cooling system conditioner through the filler neck. Cooling System Conditioner (Part No. SOA635071)
  3. Fill the engine coolant into the coolant filler tank up to the filler neck level. Coolant capacity (Fill up to "FULL" level): MT model 7.7 US qt. (6.4 Imp qt.) AT model 7.6 US qt. (6.3 Imp qt.)
    CAUTION: Do not confuse the cap of the coolant filler tank and the cap of the radiator.
    NOTE: When pouring the engine coolant, the radiator side cap must not be removed. The SUBARU Genuine Coolant containing antifreeze and anti-rust agents is especially made for the SUBARU engine, which has an aluminum crankcase. Always use SUBARU Genuine Coolant, since other coolant may cause corrosion.
  4. Fill engine coolant into the reservoir tank up to "FULL" level.
  5. Warm up the engine completely for more than five minutes at 2,000 to 3,000 RPM.
  6. If the engine coolant level drops in the coolant filler tank, add engine coolant to the filler neck level.
  7. If the engine coolant level drops from "FULL" level of reservoir tank, add engine coolant to "FULL" level.
  8. Reinstall the coolant filler tank cap and reservoir tank cap properly.
  1. Pour cooling system conditioner through the filler neck. Cooling System Conditioner (Part No. SOA635071)
  2. Pour engine coolant into the radiator up to the filler neck level. Coolant Capacity (Fill up to "Full" level): 7.6 US qt. (6.3 Imp qt.)
    NOTE: The SUBARU Genuine Coolant containing antifreeze and anti-rust agents is especially made for the SUBARU engine, which has an aluminum crankcase. Always use SUBARU Genuine Coolant, since other coolant may cause corrosion.
  3. Fill engine coolant into the reservoir tank up to "FULL" level.
  4. Warm up the engine completely for more than five minutes at 2,000 to 3,000 RPM.
  5. If the engine coolant level drops in coolant filler tank, add engine coolant to filler neck level.
  6. If the engine coolant level drops from "FULL" level of reservoir tank, add engine coolant to "FULL" level.
  7. Reinstall the coolant filler tank cap and reservoir tank cap properly.

B9 Tribeca 

  1. Pour cooling system conditioner through the filler neck. Cooling System Conditioner (Part No. SOA635071)
  2. Pour engine coolant into the radiator up to the filler neck level. (Refer to H6 for coolant capacity)
    NOTE: The SUBARU Genuine Coolant containing antifreeze and anti-rust agents is especially made for the SUBARU engine, which has an aluminum crankcase. Always use SUBARU Genuine Coolant, since other coolant may cause corrosion.
  3. Open the air bleed valve on the heater hose side.
  4. If the engine coolant level drops, add engine coolant into the radiator up to the filler neck level.
  5. When engine coolant has come out from the air bleed valve on the heater hose side, close the valve.
  6. Open the air bleed valve on the radiator side.
  7. If the engine coolant level drops, add engine coolant into the radiator up to the filler neck level.
  8. When engine coolant has come out from the air bleed valve on the radiator side, close the valve.
  9. Fill engine coolant into the reservoir tank up to the "FULL" level.
  10. Close the radiator cap and start the engine. Rev the engine 5 to 6 times at less than 3,000 RPM, then stop the engine. (Complete this operation within 40 seconds)
  11. Wait for one minute after the engine stops, open the radiator cap. If the engine coolant level drops, add engine coolant into the radiator up to the filler neck level.
  12. Perform procedures 10 and 11 one additional time.
  13. Reinstall the radiator cap and reservoir tank cap properly.
  14. Start the engine and operate the heater at maximum hot position and the blower speed set to "Lo".
  15. Run the engine at 2,000 RPM or less until radiator fan starts and stops.
    NOTE: Carefully monitor the engine coolant temperature gauge to prevent overheating.
  16. Stop the engine and wait until the engine coolant temperature falls below 86'F (30'C).
  17. Open the radiator cap. If the engine coolant level drops, add engine coolant into the radiator up to the filler neck level and reservoir tank to the "FULL" level.
  18. Reinstall the radiator cap and reservoir tank cap properly.
  19. Set the heater setting to maximum hot position and the blower speed setting to "Lo" and start the engine and rev engine at less than 3,000 RPM. If the flowing sound is heard at this time, perform the procedures from step  15 on again.

INSPECTION

Relationship of SUBARU coolant concentration and freezing temperature: Concentration and safe operating temperature of SUBARU coolant is shown in the following diagram. Measuring the temperature and specific gravity of the coolant will provide this information.

Fig 13: SUBARU Coolant Concentration
G06146434

Based on the chart above, after the second drain, approximately 3.5-4Qts. of non-diluted coolant should be added along with 1.2-1.7Qts. of water to attain the 50% mixture of each.

NOTE: Use coolant with 50% density when reservoir tank is filled up to the "FULL" Level.

SERVICE PROGRAM IDENTIFICATION LABEL

Type or print the necessary information on a Service Program identification label. The completed label should be attached to the vehicle's upper radiator support.

A quantity of labels has been sent each dealer along with their affected VIN list. Additional labels are available through the Customer Dealer Services Department (CDS) at 1-866-782-2782.

Fig 14: Service Program Identification Label
G06146435

CLAIM REIMBURSEMENT AND ENTRY PROCEDURES

Credit to perform this Service Program will be based on the submission of properly completed repair order information. Dealers may enter the applicable claim information through their Dealer Communications System.

Each dealer performing this Service Program should submit a "one time only" sublet charge for $20.00 on the first submitted claim. The sublet charge will serve as compensation for the equipment needed to perform this Service Program and may only be claimed on the first submitted claim. Subsequent claims should not include this charge.

Flush & Refill Engine Cooling System  - Enter labor operation information as follows:

LABOR OPERATION INFORMATION

CLAIM TYPE CAMPAIGN CODE LABOR OPERATION MODEL LABOR TIME LABOR DESCRIPTION PARTS
RC WWY-09 172-458 Baja, Legacy & Outback 1.0 Flush and Refill Engine Cooling System 1 Quart of Subaru Coolant SOA635002; Quantity 4 Needed. And 1 Bottle Subaru Cooling System Conditioner SOA635071; Quantity 1 Needed
B9 Tribeca 1.3

Subaru of America, Inc. 

Subaru Plaza 

P.O. Box 6000 

Cherry Hill, NJ 08034-6000 

www.subaru.com 

Service Program WWY-09 

Engine Cooling System June 2006 

Dear Subaru Owner: 

We would like to thank you for selecting a 2006 Subaru vehicle. At Subaru, we take pride in our products and are committed to your continued satisfaction. During a quality review, we discovered that the coolant used during production in your vehicle's engine cooling system may contain a higher level of chlorine than intended. If left uncorrected, this condition may quickly cause premature corrosion to occur within the components of the cooling system. To prevent corrosion, Subaru will flush out and replace the coolant in your vehicle's engine cooling system.

WHAT WE ARE ASKING YOU TO DO PROMPTLY 

We suggest that you schedule an appointment with your Subaru Dealer as soon as possible to have the engine cooling system serviced. This will help maintain your vehicle's optimum performance and prevent cooling system corrosion from occurring. Your Subaru dealer will perform this repair at no cost to you. The approximate time to perform this repair varies by model and takes between one hour and one hour and 20 minutes. However, it may be necessary for you to leave your car for a longer period on the day of your scheduled appointment to allow your dealer flexibility in scheduling other appointments.

Please present this letter to your Subaru Dealer on the day of your service appointment.

CHANGED YOUR ADDRESS OR SOLD YOUR SUBARU? 

If you have changed your address, or if you have sold your Subaru, please complete the enclosed prepaid postcard and mail it to us.

IF YOU NEED FURTHER ASSISTANCE 

To locate your nearest Subaru Dealer, you can access our web site at www.Subaru.com and go to the dealer locator function. Or, you may call us at 1-800SUBARU3 (1-800-782-2783) during normal business hours. Please call or write (using the address at the top of this letter) us immediately if the dealer fails or is unable to complete this procedure free of charge.

Your continued satisfaction with Subaru is important to us. This service is intended to assure your vehicle's optimal performance. We appreciate your understanding in this matter and regret any inconvenience this may cause you.

Sincerely,

Subaru of America, Inc.

Notice to Lessors 

The lessor of a vehicle who receives this letter is requested to provide a copy of it to the vehicle lessee(s) within 10 business days from receipt. The lessor should also keep a record of the lessee(s) to whom this letter is sent, the date sent, and the applicable vehicle identification number (VIN). (For the purposes of this section, a lessor means a person or entity that in the last twelve months prior to the date of this notification has been the owner, as referenced on the vehicle's title, of any five or more leased vehicles. A leased vehicle is a vehicle leased to another person for a term of at least four months.) 

A subsidiary of Fuji Heavy Industries Ltd.