LEMON Manuals: Even more car manuals for everyone

DTC P1235: High Pressure Fuel Pump Circuit: Procedure

  1. INSPECT FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE) 
    1. Inspect the fuel pump assembly (for high pressure). Refer to INSPECTION [07/2013 - ] .

    NG → See step   7 

    OK: Go to next step 

  2. CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - FUEL PUMP ASSEMBLY) 
    1. Disconnect the injector driver (EDU) connector.
    2. Disconnect the fuel pump assembly (for high pressure) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for open)

      Tester Connection Condition Specified Condition
      C2-3 (FP-) - C29-2 Always Below 1 Ω
      C2-4 (FP+) - C29-1 Always Below 1 Ω

      Standard Resistance (Check for short)

      Tester Connection Condition Specified Condition
      C2-3 (FP-) or C29-2 - Body ground Always 10 kΩ or higher
      C2-4 (FP+) or C29-1 - Body ground Always 10 kΩ or higher

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  3. CHECK HARNESS AND CONNECTOR (ECM - INJECTOR DRIVER (EDU)) 
    1. Disconnect the ECM connector.
    2. Disconnect the injector driver (EDU) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for open)

      Tester Connection Condition Specified Condition
      A34-32 (FPD) - C1-8 (FPD) Always Below 1 Ω
      A34-13 (FPF) - C1-7 (FPF) Always Below 1 Ω

      Standard Resistance (Check for short)

      Tester Connection Condition Specified Condition
      A34-32 (FPD) or C1-8 (FPD) - Body ground Always 10 kΩ or higher
      A34-13 (FPF) or C1-7 (FPF) - Body ground Always 10 kΩ or higher

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  4. INSPECT ECM (FPD VOLTAGE) 
    1. Turn the ignition switch to ON.
    2. Inspect the ECM using an oscilloscope.
      1. While idling the engine, check the waveform the terminals of the ECM connector.
        ECM Terminal Name A34-32 (FPD) - Body ground
        Tester Range 2 V/DIV., 20 ms./DIV.
        Condition Idling
        GTY391496Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        TEXT IN ILLUSTRATION

        *a Component with harness connected
        (ECM)
        *b FPD Terminal Waveform Normal Waveform

        Standard

        Signal waveform appears as shown in the illustration.

        HINT: 

        The FPD terminal waveform is output only right after the engine starts. If this DTC is stored when the engine is started from ignition switch off, the system enters fail-safe mode and the waveform is not output.

    NG → See step   6 

    OK: Go to next step 

  5. INSPECT ECM (FPF VOLTAGE) 
    1. Turn the ignition switch to ON.
    2. Inspect the ECM using an oscilloscope.
      1. While idling the engine, check the waveform the terminals of the ECM connector.
        ECM Terminal Name CH1: A34-32 (FPD) - Body ground
        CH2: A34-13 (FPF) - Body ground
        Tester Range 2 V/DIV., 20 ms./DIV.
        Condition Idling
        GTY391702Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        GTY384917Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        TEXT IN ILLUSTRATION

        *a Component with harness connected
        (ECM)
        *b FPD Terminal and FPF Terminal Waveform Normal Waveform
        *c FPF Terminal Waveform NG Waveform 1
        *d FPF Terminal Waveform NG Waveform 2

        HINT: 

        *: If the FPF terminal waveform is similar to the FPF terminal waveform NG waveform 1, stop the engine and disconnect injector driver (EDU) connector. Then, while cranking the engine, check to see if there is a difference between the FPF terminal waveform and the previous one.

      Result

      FPD Terminal Waveform FPF Terminal Waveform Proceed to
      OK OK A
      OK NG waveform 1* Does not change from NG waveform 1 (FPF terminal waveform remains at GND even after disconnecting the injector driver (EDU) connector and cranking the engine) A
      Changes to NG waveform 2 (FPF terminal waveform rises from GND after disconnecting the injector driver (EDU) connector and cranking the engine) B
      OK NG waveform 2 B

    B → See step   9 

    A → See step   8 

  6. INSPECT ECM (FPD VOLTAGE) 
    1. Turn the ignition switch to ON.
    2. Disconnect the injector driver (EDU) connector.
    3. Inspect the ECM using an oscilloscope.
      1. While cranking the engine, check the waveform the terminals of the ECM connector.
        ECM Terminal Name A34-32 (FPD) - Body ground
        Tester Range 2 V/DIV., 20 ms./DIV.
        Condition Cranking
        GTY391495Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        TEXT IN ILLUSTRATION

        *a Component with harness connected
        (ECM)
        *b FPD Terminal Waveform Normal Waveform

        Standard

        Signal waveform appears as shown in the illustration.

    NG → See step   8 

    OK → See step   9 

  7. REPLACE FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE). Refer to  REMOVAL [07/2013 - ] 
  8. REPLACE ECM. Refer to  REMOVAL [07/2013 - 12/2013] 
  9. REPLACE INJECTOR DRIVER (EDU). Refer to  REMOVAL [07/2013 - ]