LEMON Manuals: Even more car manuals for everyone

DTC P0617: Starter Relay Circuit High: Procedure

  1. READ VALUE USING TECHSTREAM (STARTER SIGNAL) 
    1. Connect to the Techstream the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
    5. Read the value displayed on the Techstream when the vehicle is driven at 20 km/h (12.43 mph) or more.
      RESULT

      Condition Starter Signal Proceed to
      Driving at 20 km/h (12.43 mph) or more OFF A
      ON
      (for Automatic transaxle)
      B
      ON
      (for Manual transaxle)
      C

    B → See step   2 

    C → See step   8 

    A → See step   16 

  2. READ VALUE USING TECHSTREAM (STARTER SIGNAL) 
    1. Disconnect the C28 park/neutral position switch connector.
    2. Connect the Techstream to the DLC3.
    3. Turn the ignition switch to ON.
    4. Turn the Techstream on.
    5. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
    6. Read the value displayed on the Techstream when the ignition switch is turned to ON.
      RESULT

      Starter Signal Proceed to
      ON A
      OFF B

    B → See step   4 

    A: Go to next step 

  3. INSPECT ECM (STA TERMINAL VOLTAGE) 
    Fig 1: ECM Connector Terminal Identification
    GTY390749Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the ECM connector.
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to ECM)
    2. Disconnect the C28 park/neutral position switch connector.
    3. Turn the ignition switch to ON.
    4. Measure the voltage according to the value(s) in the table below.
      RESULT

      Tester Connection Switch Condition Specified Condition Proceed to
      A21-48 (STA) - Body ground Ignition switch ON 11 to 14 V A
      Below 1.5 V B

    B → See step   14 

    A → REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH - ST RELAY) 

  4. INSPECT PARK/NEUTRAL POSITION SWITCH 
    Fig 2: Measuring Resistance Of Park/Neutral Position Switch Connector
    GTY341823Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the C28 park/neutral position switch connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      4(B) - 5(L) Shift lever in any position other than P or N 10 kΩ or higher
      2(RB) - 5(L) Always 10 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Park/Neutral Position Switch)
      RESULT

      Result Proceed to
      Outside standard range
      4(B) - 5(L)
      A
      Outside standard range
      2(RB) - 5(L)
      B
      Within standard range C

    B → REPLACE PARK/NEUTRAL POSITION SWITCH 

    C → See step   6 

    A: Go to next step 

  5. REPLACE PARK/NEUTRAL POSITION SWITCH 
    1. Replace the park/neutral position switch. Refer to REMOVAL .

    NEXT: Go to next step 

  6. INSPECT IGNITION SWITCH 
    1. Inspect the ignition switch. Refer to INSPECTION - Step 1 .

    NG → See step   15 

    OK: Go to next step 

  7. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS) 
    Fig 3: Measuring Voltage Of Park/Neutral Position Switch Connector
    GTY384973Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the A21 and C19 ECM connectors.
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Park/Neutral Position Switch)
    2. Disconnect the park/neutral position switch connector.
    3. Turn the ignition switch to ON.
    4. Measure the voltage according to the value(s) in the table below.
      RESULT

      Tester Connection Switch Condition Specified Condition Proceed to
      C28-4 - Body ground Ignition switch ON 11 to 14 V A
      Below 1.5 V B

    B → See step   14 

    A → REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - PARK/NEUTRAL POSITION SWITCH - ECM) 

  8. READ VALUE USING TECHSTREAM (STARTER SIGNAL) 
    1. Disconnect the A17 clutch start switch connector.
    2. Connect the Techstream to the DLC3.
    3. Turn the ignition switch to ON.
    4. Turn the Techstream on.
    5. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
    6. Read the value displayed on the Techstream when the ignition switch is turned to ON.
      RESULT

      Starter Signal Proceed to
      ON A
      OFF B

    B → See step   10 

    A: Go to next step 

  9. INSPECT ECM (STA TERMINAL VOLTAGE) 
    Fig 4: ECM Connector Terminal Identification
    GTY390749Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the ECM connector.
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to ECM)
    2. Disconnect the A17 clutch start switch connector.
    3. Turn the ignition switch to ON.
    4. Measure the voltage according to the value(s) in the table below.
      RESULT

      Tester Connection Switch Condition Specified Condition Proceed to
      A21-48 (STA) - Body ground Ignition switch ON 11 to 14 V A
      Below 1.5 V B

    B → See step   14 

    A → REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH START SWITCH - ST RELAY) 

  10. INSPECT CLUTCH START SWITCH 
    1. Inspect the clutch start switch. Refer to INSPECTION .
      RESULT

      Result Proceed to
      Outside standard range A
      Within standard range B

    B → See step   12 

    A: Go to next step 

  11. REPLACE CLUTCH START SWITCH 
    1. Replace the clutch start switch. Refer to REMOVAL .

    NEXT: Go to next step 

  12. INSPECT IGNITION SWITCH 
    1. Inspect the ignition switch. Refer to INSPECTION - Step 1 .

    NG → See step   15 

    OK: Go to next step 

  13. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS) 
    Fig 5: Measuring Voltage Of Clutch Start Switch Connector
    GTY391849Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the A21 and C19 ECM connectors.
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Clutch Start Switch)
    2. Disconnect the clutch start switch connector.
    3. Turn the ignition switch to ON.
    4. Measure the voltage according to the value(s) in the table below.
      RESULT

      Tester Connection Switch Condition Specified Condition Proceed to
      A17-2 - Body ground Ignition switch ON 11 to 14 V A
      Below 1.5 V B

    B → See step   14 

    A → REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - CLUTCH START SWITCH - ECM) 

  14. REPLACE ECM. Refer to  REMOVAL 
  15. REPLACE IGNITION SWITCH. Refer to  REMOVAL 
  16. CHECK FOR INTERMITTENT PROBLEMS. Refer to  CHECK FOR INTERMITTENT PROBLEMS