LEMON Manuals: Even more car manuals for everyone

DTC P0617: Starter Relay Circuit High: Procedure

  1. READ VALUE USING TECHSTREAM (STARTER SIGNAL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
    5. Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.

      OK

      Ignition Switch Position Starter Signal
      ON Close (Starter signal OFF)
      START Open (Starter signal ON)

    NG → See step   2 

    OK → See step   12 

  2. READ VALUE USING TECHSTREAM (STARTER SIGNAL) 
    Fig 1: Identifying Clutch Start Switch And Park/Neutral Position Switch Connector Terminals
    GTY160925Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the clutch start switch or the Park/Neutral Position (PNP) switch connector.
    2. Connect the Techstream to the DLC3.
    3. Turn the ignition switch to ON.
    4. Turn the Techstream on.
    5. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
    6. Check the value displayed on the Techstream when the ignition switch is turned to ON.
      RESULT

      Result Proceed to
      Remains ON A
      OFF (M/T models) B
      OFF (A/T models) C
    7. Reconnect the clutch start switch or the Park/Neutral Position (PNP) switch connector.

    B → See step   4 

    C → See step   8 

    A: Go to next step 

  3. INSPECT ECM (STA TERMINAL VOLTAGE) 
    Fig 2: Identifying ECM Connector Terminals
    GTY166237Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the clutch start switch or the Park/Neutral Position (PNP) switch connector.
    2. Disconnect the ECM connector.
    3. Turn the ignition switch to ON.
    4. Measure the voltage according to the value(s) in the table below.
      RESULT

      Tester Connection Switch Condition Specified Condition Proceed to
      STA (A36-48) - Body ground Ignition switch ON 11 to 14 V A
      Below 1.5 V B
    5. Reconnect the clutch start switch or the Park/Neutral Position (PNP) switch connector.
    6. Reconnect the ECM connector.

    B → See step   18 

    A → REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ST RELAY - CLUTCH START SWITCH OR PNP SWITCH) 

  4. INSPECT CLUTCH START SWITCH 
    Fig 3: Identifying Clutch Start Switch Connector Terminals
    GTY161103Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the clutch start switch connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      1 - 2 OFF (free) 10 kΩ or higher
      RESULT

      Result Proceed to
      Outside standard range A
      Within standard range B
    3. Reconnect the clutch start switch connector.

    B → See step   6 

    A: Go to next step 

  5. REPLACE CLUTCH START SWITCH 
    1. Replace the clutch start switch. Refer to REMOVAL .

    NEXT: Go to next step 

  6. INSPECT IGNITION SWITCH 
    Fig 4: Inspecting Ignition Switch
    GTY165527Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the ignition switch.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      All Terminals LOCK 10 kΩ or higher
      2 (AM1) - 3 (ACC) ACC Below 1 Ω
      2 (AM1) - 3 (ACC) - 4 (IG1) ON
      7 (AM2) - 6 (IG2)
      2 (AM1) - 4 (IG1) - 1 (ST1) START
      7 (AM2) - 6 (IG2) - 8 (ST2)
    3. Reinstall the ignition switch.

    NG → See step   17 

    OK: Go to next step 

  7. INSPECT ECM (NSW TERMINAL VOLTAGE) 
    Fig 5: Identifying ECM Connector
    GTY165814Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the clutch start switch connector.
    2. Disconnect the ECM connector.
    3. Turn the ignition switch to ON.
    4. Measure the voltage according to the value(s) in the table below.
      RESULT

      Tester Connection Switch Condition Specified Condition Proceed to
      NSW (B33-52) - Body ground Ignition switch ON 11 to 14 V A
      Below 1.5 V B
    5. Reconnect the clutch start switch connector.
    6. Reconnect the ECM connector.

    B → See step   16 

    A → REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - CLUTCH START SWITCH - ECM) 

  8. INSPECT PARK/NEUTRAL POSITION SWITCH 
    Fig 6: Identifying Park/Neutral Position Switch Connector Terminals
    GTY163785Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the Park/Neutral Position (PNP) switch connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Short)

      Tester Connection Condition Specified Condition
      4 - 5 Shift lever position except P and N 10 kΩ or higher
      2 - 5 All shift lever positions
      (P, R, N, D and S)
      10 kΩ or higher
      RESULT

      Result Proceed to
      Short between 4 and 5 A
      Short between 2 and 5 B
      Within standard range C
    3. Reconnect the PNP switch connector.

    B → See step   15 

    C → See step   10 

    A: Go to next step 

  9. REPLACE PARK/NEUTRAL POSITION SWITCH 
    1. Replace park/neutral position switch. Refer to REMOVAL .

    NEXT: Go to next step 

  10. INSPECT IGNITION SWITCH 
    Fig 7: Inspecting Ignition Switch
    GTY165527Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the ignition switch.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition
      All Terminals LOCK 10 kΩ or higher
      2 (AM1) - 3 (ACC) ACC Below 1 Ω
      2 (AM1) - 3 (ACC) - 4 (IG1) ON
      7 (AM2) - 6 (IG2)
      2 (AM1) - 4 (IG1) - 1 (ST1) START
      7 (AM2) - 6 (IG2) - 8 (ST2)
    3. Reinstall the ignition switch.

    NG → See step   13 

    OK: Go to next step 

  11. INSPECT ECM (NSW TERMINAL VOLTAGE) 
    Fig 8: Identifying ECM Connector
    GTY165814Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the Park/Neutral Position (PNP) switch connector.
    2. Disconnect the ECM connector.
    3. Turn the ignition switch to ON.
    4. Measure the voltage according to the value(s) in the table below.
      RESULT

      Tester Connection Switch Condition Specified Condition Proceed to
      NSW (B33-52) - Body ground Ignition switch ON 11 to 14 V A
      Below 1.5 V B
    5. Reconnect the PNP switch connector.
    6. Reconnect the ECM connector.

    B → See step   14 

    A → REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - PNP SWITCH - ECM) 

  12. CHECK FOR INTERMITTENT PROBLEMS. Refer to  CHECK FOR INTERMITTENT PROBLEMS 
  13. REPLACE IGNITION SWITCH. Refer to  REMOVAL 
  14. REPLACE ECM. Refer to  REMOVAL 
  15. REPLACE PARK/NEUTRAL POSITION SWITCH. Refer to  REMOVAL 
  16. REPLACE ECM. Refer to  REMOVAL 
  17. REPLACE IGNITION SWITCH. Refer to  REMOVAL 
  18. REPLACE ECM. Refer to  REMOVAL