Mil On W/DTC P0327 In Pcm Memory (98-T-26)
Publication date: 1998-07-01Reference number: 98-T-26
MIL ON W/DTC P0327 IN PCM MEMORY
TECHNICAL SERVICE BULLETIN
MIL (SERVICE ENGINE SOON TELLTALE LAMP) ON WITH DTC P0327 IN PCM MEMORY (INSTALL SERVICE PCM CALIBRATION)
APPLICATION
Model(s): 1999 Saturn SC1, SC2, SL, SL1, SL2, SW1, SW2
Group/Seq. No.: Engine - 03
Corporation No.: 886004
Bulletin No.: 98-T-26
Date: July, 1998
VEHICLES AFFECTED
1999 Saturn vehicles built up to and including the following VIN breakpoints:
| Engine | Transaxle | Emissions | Breakpoint |
|---|---|---|---|
| SOHC | Manual | All | XZ114516 |
| SOHC | Automatic | All | XZ114579 |
| DOHC | Manual | Federal | XZ114501 |
| DOHC | Automatic | Federal | XZ114748 |
| DOHC | Manual | California | XZ118246 |
| DOHC | Automatic | California | XZ114636 |
CONDITION
The malfunction indicator lamp (MIL) (SERVICE ENGINE SOON telltale lamp) may be On with diagnostic trouble code (DTC) P0327 (Knock Sensor Circuit) present or stored in the powertrain control module (PCM) malfunction history.
CAUSE
Condition may be present because the initial DTC P0327 diagnostic calibration did not allow for normal build variation.
CORRECTION
Install service PCM calibration if indicated in the following procedure.
PROCEDURE
- Connect a Scan tool or the Service Stall System (SSS) to the vehicle and turn the Ignition On.
- The Tech 2 displays the "Controller Part Number" parameter within the "Vehicle System Information" table.
- The portable diagnostic tool (PDT) displays the "PCM Part #" parameter within the "Vehicle ID" table.
- The SSS displays the "Controller Part Number" parameter within the "Vehicle ID" table.
- Refer to the table below and verify proper calibration.
- If the controller/PCM part number does not match one of the numbers listed in the "New End Model" column below, then reprogram the PCM. (Refer to "Reprogramming EEPROM" in the "Service Stall System User Guide.")
- If the controller/PCM part number does match one of the numbers listed in the "New End Model" column below, refer to DTC P0327 diagnostics in the 1998- 1999 model year"Powertrain Controls Service Manual."NOTE: Version 44.50 or greater Service Stall System (SSS) software is required for this re-calibration process. Verify the SSS is version 44.50 or greater.NOTE: If SSS version 44.50 or greater is not available, call the Saturn Customer Support Center at 1-800-7SATURN (1-800-772-8876), prompt 3. In Canada, call 1-800-828-6860 for English, or 1-800-503-3222 for French.CONTROLLER/PCM PART NUMBERS (END MODEL) INFORMATION
Emissions Engine Transaxle New End Model Prior End Model Federal Base (L24) Automatic 21008922 21008892 Federal Base (L24) Manual 21008925 21008895 Federal Perf (LL0) Automatic 21008920 21008890 Federal Perf (LL0) Manual 21008923 21008893 California Base (L24) Automatic 21008922 21008892 California Base (L24) Manual 21008925 21008895 California Perf (LL0) Automatic 21008921 21008891 California Perf (LL0) Manual 21008924 21008894 Taiwan/Canada Base (L24) Automatic 21008922 21008892 Taiwan/Canada Base (L24) Manual 21008925 21008895 Taiwan/Canada Perf (LL0) Automatic 21008920 21008890 Taiwan/Canada Perf (LL0) Manual 21008923 21008893
- Use the Scan tool to verify complaint has been corrected by monitoring ESC PASS COUNTER for 20 seconds after engine start up.
- If ESC PASS COUNTER is greater than or equal to three, complaint has been corrected.
- If ESC PASS COUNTER is less than or equal to two, refer to DTC P0327 diagnostics in 1998-99 model year "Powertrain Controls Service Manual".
WARRANTY INFORMATION
To receive credit for this repair during the warranty coverage period, submit a claim through the Saturn Dealer System as follows:
Case Type: VW
Labor Operation No.: J6355 - EEPROM-Reprogramming
Time: 0.3 hr.