LEMON Manuals: Even more car manuals for everyone

Intake Manifold: Adjustment/Replacement: Disassembly

Remove the fuel pipe protector LH.

Fig 1: Removing Fuel Pipe Protector LH
G03872569Courtesy of SAAB-SCANIA OF AMERICA, INC.

Remove the fuel pipe protector RH.

Fig 2: Removing Fuel Pipe Protector RH
G03872570Courtesy of SAAB-SCANIA OF AMERICA, INC.

Remove the engine ground terminal from the intake manifold.

Fig 3: Removing Engine Ground Terminal From Intake Manifold (1 Of 2)
G03872571Courtesy of SAAB-SCANIA OF AMERICA, INC.
Fig 4: Removing Engine Ground Terminal From Intake Manifold (2 Of 2)
G03872572Courtesy of SAAB-SCANIA OF AMERICA, INC.

Disconnect the connector from the throttle position sensor (A), idle air control solenoid valve (B) and manifold absolute pressure sensor (C).

Disconnect the engine harness fixed by clip (D) from the intake manifold.

Fig 5: Disconnecting Connector From Throttle Position Sensor, Idle Air Control Solenoid Valve And Manifold Absolute Pressure Sensor
G03872573Courtesy of SAAB-SCANIA OF AMERICA, INC.

Remove the throttle body from the intake manifold.

Fig 6: Removing Throttle Body From Intake Manifold
G03872574Courtesy of SAAB-SCANIA OF AMERICA, INC.

Disconnect the connector from the fuel injector.

Fig 7: Disconnecting Fuel Injector Connector
G03872575Courtesy of SAAB-SCANIA OF AMERICA, INC.

Disconnect the connector from the tumble generator valve actuator.

Fig 8: Disconnecting Generator Tumble Generator Valve Actuator Connector
G03872576Courtesy of SAAB-SCANIA OF AMERICA, INC.

Disconnect the connector from the tumble generator valve sensor.

Fig 9: Disconnecting Tumble Generator Valve Sensor Connector
G03872577Courtesy of SAAB-SCANIA OF AMERICA, INC.

Disconnect the connector from the purge control solenoid valve.

Fig 10: Disconnecting Purge Control Solenoid Valve Connector
G03872578Courtesy of SAAB-SCANIA OF AMERICA, INC.

Remove the purge control solenoid valve.

Fig 11: Removing Purge Control Solenoid Valve
G03872579Courtesy of SAAB-SCANIA OF AMERICA, INC.

Disconnect the evaporation hose from the intake manifold.

Fig 12: Disconnecting Evaporation Hose From Intake Manifold
G03872580Courtesy of SAAB-SCANIA OF AMERICA, INC.

Disconnect the evaporation hoses from the purge valve.

Fig 13: Disconnecting Evaporation Hoses From Purge Valve
G03872581Courtesy of SAAB-SCANIA OF AMERICA, INC.

Remove the two bolts which hold the fuel pipes on the left side of intake manifold.

Fig 14: Removing Fuel Pipes On Left Side Of Intake Manifold
G03872582Courtesy of SAAB-SCANIA OF AMERICA, INC.

Remove the bolt which hold the fuel injector pipe onto intake manifold.

Remove the fuel injector.

Fig 19: Removing Fuel Injector
G03872587Courtesy of SAAB-SCANIA OF AMERICA, INC.

Remove the harness bracket which holds the engine harness onto intake manifold.

Fig 20: Removing Engine Harness Onto Intake Manifold Bracket
G03872588Courtesy of SAAB-SCANIA OF AMERICA, INC.

Remove the engine harness from the intake manifold.

Loosen the clamp which holds the front left side fuel hose to injector pipe and remove the pipe from clamp.

Fig 21: Loosening Clamp Which Holds Front Left Side Fuel Hose To Injector Pipe And Remove Pipe From Clamp
G03872589Courtesy of SAAB-SCANIA OF AMERICA, INC.

Remove the fuel injector pipe LH.

Remove the bolts which install the fuel pipe on intake manifold.

Fig 22: Removing Bolts Which Install Fuel Pipe On Intake Manifold
G03872590Courtesy of SAAB-SCANIA OF AMERICA, INC.

Remove the fuel pipe assembly and pressure regulator, from the intake manifold.

Remove the intake duct from the intake manifold.

Fig 23: Removing Intake Duct From Intake Manifold
G03872591Courtesy of SAAB-SCANIA OF AMERICA, INC.

Remove the tumble generator valve assembly from the intake manifold.

Fig 24: Removing Tumble Generator Valve Assembly From Intake Manifold
G03872592Courtesy of SAAB-SCANIA OF AMERICA, INC.