LEMON Manuals: Even more car manuals for everyone

Intake Manifold: Adjustment/Replacement: Assembly

NOTE: Replace the gasket with a new one.

Install the tumble generator valve assembly to the intake manifold.

Tightening torque: 

8.25 Nm (0.84 kgf-m, 6.1 ft-lb) 

Fig 1: Installing Tumble Generator Valve Assembly To Intake Manifold
G03872593Courtesy of SAAB-SCANIA OF AMERICA, INC.

Install the air intake duct to the intake manifold.

Tightening torque: 

19 Nm (1.94 kgf-m, 13.7 ft-lb) 

Fig 2: Installing Air Intake Duct To Intake Manifold
G03872594Courtesy of SAAB-SCANIA OF AMERICA, INC.

Install the fuel pipe assembly and pressure regulator to the intake manifold.

Tightening torque: 

4.9 Nm (0.5 kgf-m, 3.6 ft-lb) 

Fig 3: Installing Fuel Pipe Assembly And Pressure Regulator To Intake Manifold
G03872595Courtesy of SAAB-SCANIA OF AMERICA, INC.

Install the fuel injector pipe LH.

Connect the left side fuel hose to injector pipe, and tighten the clamp screw.

Fig 4: Connecting Left Side Fuel Hose To Injector Pipe
G03872596Courtesy of SAAB-SCANIA OF AMERICA, INC.

Install the engine harness to the intake manifold.

Install the harness bracket which holds the engine harness onto intake manifold.

Tightening torque: 

19 Nm (1.94 kgf-m, 13.7 ft-lb) 

Fig 5: Installing Engine Harness To Intake Manifold Bracket
G03872597Courtesy of SAAB-SCANIA OF AMERICA, INC.

Install the fuel injector.

Fig 6: Installing Fuel Injector
G03872598Courtesy of SAAB-SCANIA OF AMERICA, INC.

Tighten the bolts which install the fuel injector pipe onto intake manifold.

Tightening torque: 

19 Nm (1.94 kgf-m, 13.7 ft-lb) 

Tighten the two bolts which install the fuel pipes on the left side of intake manifold.

Tightening torque: 

4.9 Nm (0.5 kgf-m, 3.6 ft-lb) 

Fig 11: Installing Fuel Pipes On Left Side Of Intake Manifold
G03872603Courtesy of SAAB-SCANIA OF AMERICA, INC.

Connect the evaporation hoses to the purge valve.

NOTE: Connect the evaporation hoses as shown in the figure.
Fig 12: Connecting Evaporation Hoses
G03872604Courtesy of SAAB-SCANIA OF AMERICA, INC.
  1. To fuel pipe ASSY
  2. To intake duct
  3. To purge control solenoid valve
  4. To intake manifold

Connect the evaporation hose to the intake manifold.

Fig 13: Connecting Evaporation Hose To Intake Manifold
G03872605Courtesy of SAAB-SCANIA OF AMERICA, INC.

Install the purge control solenoid valve.

Tightening torque: 

16 Nm (1.6 kgf-m, 11.8 ft-lb) 

Fig 14: Installing Purge Control Solenoid Valve
G03872606Courtesy of SAAB-SCANIA OF AMERICA, INC.

Connect the hoses to the purge control solenoid valve.

NOTE: Connect the evaporation hoses as shown in the figure.
Fig 15: Connecting Evaporation Hoses
G03872607Courtesy of SAAB-SCANIA OF AMERICA, INC.
  1. To intake manifold
  2. To purge valve

Connect the connector to the purge control solenoid valve.

Fig 16: Connecting Purge Control Solenoid Valve Connector
G03872608Courtesy of SAAB-SCANIA OF AMERICA, INC.

Connect the connector to the tumble generator valve sensor.

Fig 17: Connecting Tumble Generator Valve Sensor Connector
G03872609Courtesy of SAAB-SCANIA OF AMERICA, INC.

Connect the connector to the tumble generator valve actuator.

Fig 18: Connecting Tumble Generator Valve Actuator Connector
G03872610Courtesy of SAAB-SCANIA OF AMERICA, INC.

Connect the connector to the fuel injector.

Fig 19: Connecting Fuel Injector Connector
G03872611Courtesy of SAAB-SCANIA OF AMERICA, INC.

Install the throttle body to the intake manifold.

NOTE: Replace the gasket with a new one.

Tightening torque: 

22 Nm (2.2 kgf-m, 15.9 ft-lb) 

Fig 20: Installing Throttle Body To Intake Manifold
G03872612Courtesy of SAAB-SCANIA OF AMERICA, INC.

Connect the connector to the throttle position sensor (A), idle air control solenoid valve (B) and manifold absolute pressure sensor (C).

Connect the engine harness to the intake manifold using clips (D).

Fig 21: Connecting Connector To Throttle Position Sensor, Idle Air Control Solenoid Valve And Manifold Absolute Pressure Sensor
G03872613Courtesy of SAAB-SCANIA OF AMERICA, INC.

Install the engine ground terminal to the intake manifold.

Tightening torque: 

19 Nm (1.94 kgf-m, 13.7 ft-lb) 

Fig 22: Installing Engine Ground Terminal To Intake Manifold (1 Of 2)
G03872614Courtesy of SAAB-SCANIA OF AMERICA, INC.
Fig 23: Installing Engine Ground Terminal To Intake Manifold (2 Of 2)
G03872615Courtesy of SAAB-SCANIA OF AMERICA, INC.

Install the fuel pipe protector RH.

Tightening torque: 

19 Nm (1.94 kgf-m, 13.7 ft-lb) 

Fig 24: Installing Fuel Pipe Protector RH
G03872616Courtesy of SAAB-SCANIA OF AMERICA, INC.

Install the fuel pipe protector LH.

Tightening torque: 

19 Nm (1.94 kgf-m, 13.7 ft-lb) 

Fig 25: Installing Fuel Pipe Protector LH
G03872617Courtesy of SAAB-SCANIA OF AMERICA, INC.