Diagnostic Aids
- Use the J 35616 Connector Test Adapter Kit for any test that requires probing the ECM harness connector or a component harness connector. See Special Tools .
- If DTCs P0700, P2122, P2128, and P2138 are set together in various combinations, inspect the APP sensor 1 and 2 signal circuits for being shorted together.
- For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections .
DTC P2128
| Step | Action | Values | Yes | No |
|---|---|---|---|---|
| Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Control Module (ECM) Connector End Views or Engine Controls Connector End Views |
||||
| 1 | Did you perform the Diagnostic System Check - Vehicle? | - | Go to Step 2 | Go to Diagnostic System Check - Vehicle |
| 2 |
|
4.2 V | Go to Step 4 | Go to Step 3 |
| 3 |
|
- | Go to Step 4 | Go to Testing for Intermittent Conditions and Poor Connections |
| 4 |
|
4.8-5.2 V | Go to Step 5 | Go to Step 10 |
| 5 | Probe the APP sensor 2 signal circuit with a test lamp connected to ground. Does the test lamp illuminate? |
- | Go to Step 8 | Go to Step 6 |
| 6 | Observe the APP Sensor 2 parameter, with the test lamp still connected to the APP sensor 2 signal circuit. Does the scan tool indicate voltage at the specified value? |
0 V | Go to Step 9 | Go to Step 7 |
| 7 | Test the APP sensor 2 signal circuit for an open or high resistance. Refer to Circuit Testing
and Wiring Repairs
. Did you find and correct the condition? |
- | Go to Step 16 | Go to Step 13 |
| 8 | Test the APP sensor 2 signal circuit for a short to voltage. Refer to Circuit Testing
and Wiring Repairs
. Did you find and correct the condition? |
- | Go to Step 16 | Go to Step 11 |
| 9 | Test the APP sensor 2 low reference circuit for an open or high resistance. Refer to Circuit Testing
and Wiring Repairs
. Did you find and correct the condition? |
- | Go to Step 16 | Go to Step 12 |
| 10 | Test the APP sensor 2 5-volt reference circuit for a short to voltage. Refer to Circuit Testing
and Wiring Repairs
. Did you find and correct the condition? |
- | Go to Step 16 | Go to Step 11 |
| 11 | Test for shorted terminals and for a poor connection at the engine control module (ECM) harness connector. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
. Did you find and correct the condition? |
- | Go to Step 16 | Go to Step 15 |
| 12 | Test for an intermittent and for a poor connection at the accelerator pedal harness connector. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
. Did you find and correct the condition? |
- | Go to Step 16 | Go to Step 14 |
| 13 | Test for an intermittent and for a poor connection at the ECM harness connector. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
. Did you find and correct the condition? |
- | Go to Step 16 | Go to Step 15 |
| 14 | Replace the accelerator pedal assembly. Refer to Accelerator Pedal with Position Sensor Replacement
. Did you complete the replacement? |
- | Go to Step 16 | - |
| 15 | Replace the ECM. Refer to Control Module References
for replacement, setup, and programming. Did you complete the replacement? |
- | Go to Step 16 | - |
| 16 |
|
- | Go to Step 2 | Go to Step 17 |
| 17 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? |
- | Go to Diagnostic Trouble Code (DTC) List - Vehicle | System OK |