LEMON Manuals: Even more car manuals for everyone

Diagnostic Procedure

WARNING: This page is about a different car, the 2005 Nissan Xterra. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK 4WD SHIFT SWITCH SIGNAL 

    With CONSULT-II 

    1. Turn ignition switch "ON".
    2. Select "DATA MONITOR" mode for "ALL MODE AWD/4WD" with CONSULT-II.
    3. Read out ON/OFF switching action of the "2WD SWITCH", "4H SWITCH", "4L SWITCH" with operating 4WD shift switch.
      Fig 1: CONSULT-II Display - "ALL MODE AWD/4WD"
      G03608264Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    1. Turn ignition switch "ON".
    2. Check voltage between transfer control unit harness connector terminals and ground.
      CONNECTOR TERMINAL VOLTAGE SPECIFICATION

      Connector Terminal Condition Voltage (Approx.)
      E152 14 - Ground 4WD shift switch: 2WD Battery voltage
      4WD shift switch: 4H and 4LO 0V
      15 - Ground 4WD shift switch: 4H Battery voltage
      4WD shift switch: 2WD and 4LO 0V
      16 - Ground 4WD shift switch: 4LO Battery voltage
      4WD shift switch: 2WD and 4H 0V
      Fig 2: Checking Voltage Between Transfer Control Unit Harness Connector Terminals Ground
      G03608265Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    1. OK: GO TO  5.
    2. NG: GO TO 2.
  2. CHECK 4WD SHIFT SWITCH POWER SUPPLY CIRCUIT 
    1. Turn ignition switch "OFF". (Stay for at least 5 seconds.)
    2. Disconnect 4WD shift switch harness connector.
    3. Check voltage between 4WD shift switch harness connector terminal 1 and ground.
      CONNECTOR TERMINAL VOLTAGE SPECIFICATION

      Connector Terminal Voltage (Approx.)
      M141 1 - Ground 0V
    4. Fig 3: Checking Voltage Between 4WD Shift Switch Harness Connector Terminal 1 Ground
      G03608266Courtesy of NISSAN MOTOR CO., U.S.A.
    5. Turn ignition switch "ON". (Do not start engine.)
    6. Check voltage between 4WD shift switch harness connector terminal 1 and ground.
      CONNECTOR TERMINAL VOLTAGE SPECIFICATION

      Connector Terminal Voltage (Approx.)
      M141 1 - Ground Battery voltage

    OK or NG 

    1. OK: GO TO 3.
    2. NG:
      1. Check harness for short or open between 4WD shift switch harness connector terminal 1 and transfer shut off relay 2 harness connector E157 terminal 5 and 10A fuse (No. 58 located in the fuse and relay box). If any items are damaged, repair or replace damaged parts.
      2. Perform trouble diagnosis for power supply circuit. Refer to , "POWER SUPPLY CIRCUIT FOR TRANSFER CONTROL UNIT ".
        Fig 4: Checking voltage between 4WD shift switch harness connector terminal 1 ground
        G03608267Courtesy of NISSAN MOTOR CO., U.S.A.
  3. CHECK HARNESS BETWEEN 4WD SHIFT SWITCH AND TRANSFER CONTROL UNIT 
    1. Turn ignition switch "OFF". (Stay for at least 5 seconds.)
    2. Disconnect transfer control unit harness connector and the 4WD shift switch harness connector.
    3. Check continuity between the following terminals.
      • Transfer control unit harness connector M152 terminal 14 and 4WD shift switch harness connector M141 terminal 3.
      • Transfer control unit harness connector M152 terminal 15 and 4WD shift switch harness connector M141 terminal 5.
      • Transfer control unit harness connector M152 terminal 16 and 4WD shift switch harness connector M141 terminal 6.

        Continuity should exist  .

        Also check harness for short to ground and short to power.

    OK or NG 

    1. OK: GO TO 4.
    2. NG: Repair or replace damaged parts.
      Fig 5: Checking Continuity Between Terminals
      G03608268Courtesy of NISSAN MOTOR CO., U.S.A.
  4. CHECK 4WD SHIFT SWITCH 
    1. Turn ignition switch "OFF". (Stay for at least 5 seconds.)
    2. Remove 4WD shift switch harness connector.
    3. Operate 4WD shift switch and check continuity between 4WD shift switch terminals.
      CONNECTOR TERMINAL CONTINUITY SPECIFICATION

      Terminal Condition Continuity
      1 - 3 4WD shift switch: 2WD Yes
      4WD shift switch: 4H and 4LO No
      1 - 5 4WD shift switch: 4H Yes
      4WD shift switch: 2WD and 4LO No
      1 - 6 4WD shift switch: 4LO Yes
      4WD shift switch: 2WD and 4H No

    OK or NG 

    1. OK: GO TO 5.
    2. NG: Replace 4WD shift switch.
      Fig 6: Checking Continuity Between 4WD Shift Switch Terminals
      G03608269Courtesy of NISSAN MOTOR CO., U.S.A.
  5. CHECK TRANSFER CONTROL UNIT 

    Check transfer control unit input/output signal. Refer to , "TRANSFER CONTROL UNIT INPUT/OUTPUT SIGNAL REFERENCE VALUES ".

    OK or NG 

    1. OK: GO TO 6.
    2. NG: Check transfer control unit pin terminals for damage or loose connection with harness connector. If any items are damaged, repair or replace damaged parts.
  6. CHECK DTC 

    Perform the self-diagnosis, after driving a vehicle for a while.

    OK or NG 

    1. OK: Inspection End.
    2. NG: Replace transfer control unit. Refer to , "REMOVAL AND INSTALLATION ".