LEMON Manuals: Even more car manuals for everyone

Essential Tool: New Consult-II Converter And Cable Set (NTB02-076A)

WARNING: This page is about the Sentra GXE, Automatic, which is a different variant/trim than selected.
Publication date: 2003-02-19
Reference number: NTB02-076A
Supersedes refnos: NTB02-076

ESSENTIAL TOOL: NEW CONSULT-II CONVERTER AND CABLE SET

ESSENTIAL TOOL: NEW CONSULT-II CONVERTER AND CABLE SET

TECHNICAL SERVICE BULLETIN

Reference Number(s): NTB02-076A, Date of Issue:  February 19, 2003
NISSAN: All vehicles with CONSULT-II Compatibility
CLASSIFICATION: TE02-015A
SECTION: Tool and Equipment
APPLIED VEHICLE(S): Cable Set: All vehicles with CONSULT-II Compatibility; Converter: New vehicles equipped with the new Control Area Network "CAN" system beginning with: 2003 350Z (Z33); 2003 Murano (Z50); 2004 Maxima (A34)
Superceded Bulletin(s): NTB02-076
NOTE: This bulletin's Applied Vehicles and Service Information sections has been amended. Please discard all earlier copies of NTB02-076.

SERVICE INFORMATION

This new essential tool replaces your old CONSULT-II cables and contains the items shown in Fig 1 , below.

CAUTION: The old-style CONSULT-II "I" and "Y" DLC-I and DLC-II cables should NOT be used anymore on any vehicle, old or new:
IMPORTANT: The "CONSULT-II Converter", with attached cables, is to be used on all vehicles with DLC-II connectors, including current and older vehicles.
CAUTION: This cable set must be used on vehicles with the "CAN" system, otherwise "CAN Fail-safe" will occur. Refer to PRODUCT USAGE/CAUTION  .
Fig 1: CONSULT-II Converter & Cable Set J-44200-CC
G00255070

CABLE HOOK-UP INFORMATION

(SEE Fig 1 )

  • CONSULT-II Pigtail: To be permanently connected to the "DDL" Port on CONSULT-II, with screws tightened.
  • DLC-I Cable: To be used when connecting CONSULT-II to early vehicles equipped with a DLC-I connector (Non-CAN system).
  • CONSULT-II Converter and Cables: Required on vehicles equipped with the new "CAN" System, including current and previous vehicles.
  • Converter Cable: To be permanently connected to the CONSULT-II converter with screws tightened; connects converter to the CONSULT-II Pigtail.
  • DLC-II Cable: To be permanently connected to the CONSULT-II converter with screws tightened; connects the converter to newer vehicle's DLC-II connector (including CAN-System equipped vehicles).

ADDITIONAL SERVICE INFORMATION

PRODUCT FEATURES

  1. Heavy duty connection between the new CONSULT-II pigtail cable and the DLC-I and DLC-II cables:
    • This will allow frequent cable swapping without damaging the male and female connector pins
    • This feature will help prevent data transfer interruptions and ECM/TCM damage during reprogramming
  2. The new cables are longer to allow easier CONSULT-II usage under the hood or under the vehicle:
    • A Velcro strap is provided to bundle and secure excess length when not needed

PRODUCT USAGE/CAUTION

  1. The following software updates are required for use with the "CONSULT-II Converter and Cable Set J-44200-CC":
    • CONSULT-II diagnostic software version AED02C or later (newer)
    • NATS software version AEN02B or later (newer).
    NOTE: The updated software is available on August 1, 2002 and later ASIST CDs.
  2. The old DLC-II cable CANNOT be used on vehicles with the new "CAN" System.
    CAUTION:
    • If you try to do this, the vehicle will go into CAN Fail-safe mode.
    • Typical symptoms of CAN Fail-safe are shown in Symptoms,

      Symptoms

      • Headlights are ON
      • Tachometer does not work
      • Tail lamps do not work
      • Warning lights are ON
      • A/C does not work
      • Cooling fans are ON
      • A\T check lamp is ON (M\T vehicles excluded)
      • Rear window defroster does not work
    • Typical DTCs stored after CAN Fail-safe are shown in Fig 2 .
    Fig 2: DTCs
    G00255071
NOTE:
  1. Normal operation will be restored (i.e., CAN Fail-safe mode stopped) when the old DLC-II cable is disconnected;
    • However, codes will be stored in the vehicle's ECUs.
    • These codes should be erased using CONSULT-II and the converter/cables.
    • For more information about "CAN Fail-safe", refer to the CONSULT-II "Diagnostics" Operation Manual in ASIST.
  2. CAN Fail-safe may occur without connecting the old DLC-II cable if there is an incident with the vehicle's wiring or control units.
  3. Complete CONSULT-II Kits sold after August 1, 2002 will include the new J-44200-CC "CONSULT-II Converter and Cable Set".
  4. The Self-Test Adapter (P/N 02002497) in the CONSULT-II kit CANNOT be used with the new Converter/DLC-II cable. However, it may be used with the new DLC-I cable.

PRODUCT AVAILABILITY AND CONTENTS

  • This new tool (i.e., J-44200-CC) is essential and has been sent to each dealer. Refer to the Tech-Mate Essential Tool Shipment flyer for additional information.
  • Each dealer's non-vehicle account will be billed plus applicable taxes and freight for this new tool. Additional tools or replacement parts can be ordered from Tech-Mate.
  • Each J-44200-CC kit contains the following:
    PARTS INFORMATION

    Description Part Number Reference Number (on part's I.D. tag)
    CONSULT-II Pigtail (Cable 1) J-44200-10 NJ0204-10
    Converter Cable (Cable 2) J-44200-20 NJ0204-20
    DLC-I Cable\Connector (Cable 3) J-44200-30 NJ0204-30
    DLC-II Cable\Connector (Cable 4) J-44200-40 NJ0204-40
    CONSULT-II Converter J-44200-50 EG1190-1000

ESSENTIAL TOOL SHIPMENT

TO: Dealer Principal and Dealer Service Manager

2002 Nissan

EG-130-02-05

The following service tools have been classified essential by Nissan North America, Inc.

  1. J-44200-CC
    CONSULT-II Converter & Cable Set

    Application: 350Z

    NOTE: This special service tool replaces your old CONSULT-II cables for use with all CONSULT-II compatible vehicles. The Converter is required for the CONSULT-II to communicate with the 350Z and other future models equipped with a new CAN (Controller Area Network) System.
    CAUTION: This cable set must be used on vehicles with the new CAN system, otherwise "CAN Fail-safe" will occur.

    The cable set features a heavy duty connection between the new CONSULT-II pigtail and the DLC-I or DLC-II cables. This will help prevent data transfer interruptions and ECM/TCM damage during reprogramming. Please refer to NTB02-076A for further information.

  2. J-45295
    TPMS Initialization Tool

    Application: 350Z

    NOTE: This Tire Pressure Monitoring System initialization tool is required to program the pressure sensors on the 350Z and future models equipped with a Low Tire Pressure Warning System. It may be used with or without the CONSULT-II to register each sensor to the vehicle.
    Fig 3: TPMS Initialization Tool
    G00255072
  3. J-45815
    A/C Disconnect Tool Set

    Application: 350Z

    NOTE: This three-piece metric A/C Line Disconnect Tool Set is identified in the ESM for 350Z. These tools are required to disconnect the "one touch" style A/C line fittings on this vehicle. Previous fractional inch sized A/C coupling tools are not compatible with the new fittings.
    Fig 4: A/C Disconnect Tool Set
    G00255073
  4. J-45674
    AT Line Pressure Adapter

    Application: 350Z

    NOTE: This adapter is used with essential Line Pressure Gauge Set J-34301-C and is required to perform oil pressure test procedures on this vehicle. It converts NPT to M10 threads with an O-ring. Please store the adapter with the J-34301-C Kit when not in use.
    Fig 5: AT Line Pressure Adapter
    G00255074
  5. J-38873-A
    Drive Plate Installer

    Application: Altima, Sentra

    NOTE: This special service tool is required for A/C Clutch installation per the ESM on Altima, Sentra, and future models. It is not necessary to replace the compressor assembly for an A/C clutch incident. Refer to NTB02-057 - AIR CONDITIONING INOPERATIVE/WARM AIR FROM A/C VENTS for this procedure on the 2002 Altima.
    Fig 6: Drive Plate Installer
    G00255075