LEMON Manuals: Even more car manuals for everyone

Diagnostic Procedure

WARNING: This page is about a different car, the 2006 Nissan Xterra. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK ACTUATOR POSITION SWITCH SIGNAL 

    With CONSULT-II 

    1. Start engine.
    2. Depress brake pedal and stop vehicle.
    3. For A/T models, set A/T selector lever to "N" position. For M/T models shift M/T selector lever to neutral.
    4. Select "DATA MONITOR" mode for "ALL MODE AWD/4WD" with CONSULT-II.
    5. Read out the value of "SHIFT POS SW1", "SHIFT POS SW2", "SHIFT POS SW3", "SHIFT POS SW4".
    MONITORED ITEM CONDITION AND DISPLAY VALUE

    Monitored item Condition Display value
    SHIFT POS SW1 4WD shift switch: 2WD and 4LO ON
    4WD shift switch: 4H OFF
    SHIFT POS SW2 4WD shift switch: 4LO ON
    4WD shift switch: 2WD and 4H OFF
    SHIFT POS SW3 4WD shift switch: 2WD and 4H ON
    4WD shift switch: 4LO OFF
    SHIFT POS SW4 4WD shift switch: 4H and 4LO ON
    4WD shift switch: 2WD OFF
    Fig 1: CONSULT II DATA MONITOR Screen
    G04204228Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    1. Start engine.
    2. Depress brake pedal and stop vehicle.
    3. For A/T models, set A/T selector lever to "N" position. For M/T models shift M/T selector lever to neutral.
    4. Check voltage between transfer control unit harness connector terminal and ground.
    TRANSFER CONTROL UNIT CONNECTOR TERMINAL AND GROUND VOLTAGE

    Connector Terminal Condition Voltage (Approx.)
    M152 10 - Ground 4WD shift switch: 2WD and 4LO OV
    4WD shift switch: 4H Battery voltage
    11 - Ground 4WD shift switch: 4LO OV
    4WD shift switch: 2WD and 4H Battery voltage
    12 - Ground 4WD shift switch: 2WD and 4H OV
    4WD shift switch: 4LO Battery voltage
    13 - Ground 4WD shift switch: 4H and 4LO OV
    4WD shift switch: 2WD Battery voltage
    Fig 2: Identifying Voltage Between Transfer Control Unit Connector Terminal And Ground
    G04204229Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO  4.

    NG: GO TO 2.

  2. CHECK HARNESS BETWEEN TRANSFER CONTROL UNIT AND ACTUATOR POSITION SWITCH 
    1. Turn ignition switch "OFF". (Stay for at least 5 seconds.)
    2. Disconnect transfer control unit harness connector and the transfer control device (actuator position switch) harness connector.
    3. Check continuity between the following terminals.
    • Transfer control unit harness connector M152 terminal 10 and transfer control device (actuator position switch) harness connector F58 terminal 26.
    • Transfer control unit harness connector M152 terminal 11 and transfer control device (actuator position switch) harness connector F58 terminal 20.
    • Transfer control unit harness connector M152 terminal 12 and transfer control device (actuator position switch) harness connector F58 terminal 21.
    • Transfer control unit harness connector M152 terminal 13 and transfer control device (actuator position switch) harness connector F58 terminal 25.

    Continuity should exist  .

    Also check harness for short to ground and short to power.

    OK or NG 

    OK: GO TO 3.

    NG: Repair or replace damaged parts.

  3. CHECK GROUND CIRCUIT 
    Fig 3: Identifying Continuity Between Transfer Control Unit And Transfer Control Device Connector Terminals
    G04204230Courtesy of NISSAN MOTOR CO., U.S.A.
    1. Turn ignition switch "OFF". (Stay for at least 5 seconds.)
    2. Check continuity between transfer control device (actuator position switch) harness connector F58 terminal 22 and ground.

    Continuity should exist  .

    Also check harness for short to power.

    OK or NG 

    OK: GO TO 4.

    NG: Repair open circuit or short to power in harness or connectors.

    Fig 4: Identifying Continuity Between Transfer Control Device Connector Terminal And Ground
    G04204231Courtesy of NISSAN MOTOR CO., U.S.A.
  4. CHECK TRANSFER CONTROL UNIT 

    Check transfer control unit input/output signal. Refer to "TRANSFER CONTROL UNIT INPUT/OUTPUT SIGNAL REFERENCE VALUES ".

    OK or NG 

    OK: GO TO 5.

    NG: Check transfer control unit pin terminals for damage or loose connection with harness connector. If any items are damaged, repair or replace damaged parts.

  5. CHECK DTC 

    Perform the self-diagnosis, after driving a vehicle for a while.

    OK or NG 

    OK: Inspection End.

    NG: Replace transfer control device. Refer to "REMOVAL AND INSTALLATION ".