LEMON Manuals: Even more car manuals for everyone

BJ Boot Replacement

Required Special Tool: 

MB991561: Boot Band Crimping Tool

  1. Remove the boot bands (large and small).
    NOTE: The boot bands cannot be re-used.
  2. Remove the BJ boot.
  3. Wrap a plastic tape around the shaft spline, and assemble the boot band and BJ boot.
    Fig 1: Removing BJ Boot
    G04259952Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  4. Align the center groove on the BJ boot small end with the shaft groove.
    Fig 2: Aligning Center Groove On BJ Boot Small End With Shaft Groove
    G04259953Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  5. Turn the adjusting bolt on special tool MB991561 so that the size of the opening (W) is at the standard value.

    Standard value (W): 2.9 mm (0.11 inch) 

    < If it is larger than 2.9 mm (0.11 inch) > Tighten the adjusting bolt. 

    < If it is smaller than 2.9 mm (0.11 inch) > Loosen the adjusting bolt. 

    NOTE: The value of W will change by approximately 0.7 mm (0.03 inch) for each turn of the adjusting bolt.
    NOTE: The adjusting bolt should not be turned more than once.
  6. Position the BJ boot band (small) so that there is even clearance at either end (A and B).
    Fig 3: Adjusting Stopper Bolt On Special Tool
    G04259954Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    Fig 4: Positioning BJ Boot Band
    G04259955Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    CAUTION:
    • Secure the drive shaft in an upright position and clamp part of the boot band to be crimped securely in the jaws of special tool MB991561.
    • Crimp the boot band until the special tool touches the stopper.
  7. Use special tool MB991561 to crimp the boot band (small).
    Fig 5: Crimping Boot Band (Small)
    G04259956Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    Fig 6: Checking Crimping Amount Of Boot Band At Standard Value
    G04259957Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  8. Check that the crimping amount (C) of the boot band is at the standard value.

    Standard value (D): 2.4 - 2.8 mm (0.09 - 0.11 inch) 

    < If the crimping amount is larger than 2.8 mm (0.11 inch) > 

    Readjust the value of (W) in step   5  according to the following formula, and then repeat the operation in step   7 . 

    W = 5.5 mm (0.22 inch) - D 

    Example: If D = 2.9 mm (0.11 inch), then W = 2.6 mm (0.10 inch). 

    < If the crimping amount is smaller than 2.4 mm (0.09 inch) > 

    Remove the EBJ boot band, readjust the value of (W) in step   5  according to the following formula, and then repeat the operations in steps   6  and   7  using a new EBJ boot band. 

    W = 5.5 mm (0.22 inch) - D 

    Example: If D = 2.3 mm (0.09 inch), then W = 3.2 mm (0.13 inch). 

  9. Check that the boot band is not sticking out past the place where it has been installed. If the boot band is sticking out, remove it and then repeat steps  6 to  8, using a new boot band.
    CAUTION: The drive shaft joint uses special grease. Do not mix old and new or different types of grease.
  10. Fill the inside of the boot with the specified amount of the specified grease.

    Specified grease: Repair kit grease 

    Amount to use < 2.4L >: 120 +/- 10 g (4.2 +/- 0.3 ounces) 

    Amount to use < 3.8L >: 165 +/- 10 g (5.8 +/- 0.3 ounces) 

  11. Align the center groove on the BJ boot big end with the BJ case groove.
    Fig 7: Aligning Center Groove On BJ Boot Big End With BJ Case Groove
    G04259958Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  12. Follow the same procedure as in step  5 to adjust the size of the opening (W) on special tool so that it is at the standard value.

    Standard value (W): 2.9 mm (0.11 inch) 

  13. Position the BJ boot band (large) so that there is even clearance at either end (D and E).
    Fig 8: Positioning BJ Boot Band Clearance End D & E
    G04259959Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    Fig 9: Checking Crimping Amount (F) Of Boot Band Standard Value
    G04259960Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  14. Use special tool to crimp the BJ boot band (large) in the same way as in step  7.
  15. Check that the crimping amount (F) of the boot band is at the standard value.

    Standard value (F): 2.4 - 2.8 mm (0.09 - 0.11 inch) 

    < If the crimping amount is larger than 2.8 mm (0.11 inch) > 

    Readjust the value of (W) in step   12  according to the following formula, and then repeat the operation in step   14 . 

    W = 5.8 mm (0.23 inch) - F 

    Example: If F = 2.9 mm (0.11 inch), then W = 2.9 mm (0.11 inch). 

    < If the crimping amount is smaller than 2.4 mm (0.09 inch) > 

    Remove the EBJ boot band, readjust the value of (W) in step   12  according to the following formula, and then repeat the operations in steps   13  and   14  using a new EBJ boot band. 

    W = 5.8 mm (0.23 inch) - F 

    Example: If F = 2.3 mm (0.09 inch), then W = 3.5 mm (0.14 inch). 

  16. Check that the boot band is not sticking out past the place where it has been installed. If the boot band is sticking out, remove it and then repeat steps  13 to  15, using a new boot band.