LEMON Manuals: Even more car manuals for everyone

Diagnostic Procedure

  1. Remove fuel cap. Disconnect and plug hose "G" at ventilation solenoid. See Figure. Connect MUT-II scan tool to OBD-II Data Link Connector (OBD-II DLC). Turn ignition on. Using scan tool, read data list item No. 73 (fuel tank pressure differential sensor). Scan tool pressure reading should be -1.5-1.5 kPa. Connect an evaporative emission system pressure pump to fuel filler neck and apply pressure. Scan tool reading should increase. Turn ignition off. If readings are not as specified, go to next step. If readings are as specified, go to step  16.
  2. Remove EVAP system pressure pump. Leave fuel cap off. Remove rear seat cushion. Remove fuel pump module cover plate. Remove FTDP sensor, leaving connector connected. Turn ignition on. Backprobe and check voltage between ground and FTDP sensor 3-pin connector terminal No. 1 (Red/Black wire). See Figure. Voltage should be 2-3 volts. If voltage is as specified, go to step  7. If voltage is not as specified, go to next step.
  3. Backprobe and check voltage between ground and FTDP sensor terminal No. 3 (Green/Yellow wire). Voltage should be 4.8-5.2 volts. If voltage is as specified, go to next step. If voltage is not as specified, go to step  8.
  4. Backprobe and check voltage between ground and FTDP sensor terminal No. 2 (Black wire). Voltage should be 500 millivolts or less. If voltage is as specified, go to next step. If voltage is not as specified, go to step  12.
  5. Turn ignition off. Check FTDP sensor connector. If problem exists, repair connector as necessary, then go to step  23. If problem does not exist, go to next step.
  6. Disconnect FTDP sensor connector. Use Special Tool (MB991658) to connect terminals No. 2 and 3 on harness side of connector to respective terminals on sensor side of connector. Turn ignition on. Remove fuel cap. Measure voltage between ground and FTDP sensor connector (component side) terminal No. 1 (Red/Black wire). Voltage should be 2-3 volts. Turn ignition off. If voltage is not as specified, replace FTDP sensor, then go to step  23. If voltage is as specified, repair wiring harness and/or connectors between FTDP sensor and PCM for short to ground, then go to step  23.
  7. With ignition on and fuel cap removed, backprobe and check voltage between ground and PCM 28-pin connector B-110 terminal No. 92 (Red/Black wire). See Figure. Voltage should be 2-3 volts. If voltage is as specified, go to step  14. If voltage is not as specified, repair wiring and/or connectors between FTDP sensor and PCM and go to step  23.
  8. Backprobe and check voltage between ground and PCM 26-pin connector B-109 terminal No. 46 (Green/Yellow wire). Voltage should be 4.8-5.2 volts. If voltage is not as specified, go to next step. If voltage is as specified, repair wiring and/or connectors between FTDP sensor and PCM, then go to step  23.
  9. Turn ignition off. Check PCM connector B-109. If problem exists, repair as necessary and go to step  23. If problem does not exist, go to next step.
  10. Disconnect PCM connector B-109. Measure resistance between ground and PCM connector B-109 terminal No. 46 (Green/Yellow wire). See Figure. If resistance is 2 ohms or more, replace PCM, then go to step  23. If resistance is less than 2 ohms, go to next step.
  11. Check all sensor power lines that originate from PCM connector B-109 terminal No. 46 (Green/Yellow wire). Repair as necessary and go to step  23.
  12. Backprobe and check voltage between ground and PCM connector B-109 terminal No. 57 (Black wire). Voltage should be 500 millivolts or less. If voltage is not as specified, go to next step. If voltage is as specified, repair wiring and/or connectors between FTDP sensor and PCM, then go to step  23.
  13. Turn ignition off. Check PCM connector B-109 for loose, damaged or corroded terminals. If problem exists, repair as necessary and go to step  23. If problem does not exist, replace PCM and go to step  23.
  14. Turn ignition off. Check PCM 28-pin connector B-110 for loose, damaged or corroded terminals. If problem exists, repair as necessary and go to step  23. If problem does not exist, go to next step.
  15. Remove fuel cap. Disconnect and plug hose "G" at ventilation solenoid end. Connect MUT-II scan tool to OBD-II Data Link Connector (OBD-II DLC). Turn ignition on. Using scan tool, read data list item No. 73 (fuel tank pressure differential sensor). Scan tool pressure reading should be -1.5-1.5 kPa. Connect EVAP system pressure pump to fuel filler neck and apply pressure. Scan tool reading should increase. Turn ignition off. If reading is as specified, go to step  23. If reading is not as specified, replace PCM, then go to step  23.
  16. NOTE: When fuel nozzle is inserted into filler neck and flapper door is opened, fuel overflow limiter valve plunger moves toward top of neck and closes fuel overflow limiter valve. When fuel cap is installed, cap pushes fuel overflow limiter valve plunger back in, which opens fuel overflow limiter valve. If flapper door or fuel overflow limiter valve plunger do not operate properly, fuel overflow limiter valve stays closed blocking vapor passage and DTC P0450 may set.
  17. Remove fuel cap. Push in flapper door to operate fuel overflow limiter valve. Fuel overflow limiter valve plunger should move toward top. Reinstall and tighten fuel cap 3 clicks. Remove fuel cap and check if fuel overflow limiter valve plunger was pushed back. Distance between tip of fuel overflow limiter valve plunger and top of fuel filler neck should be 1.1" (28 mm) or more. If fuel overflow limiter valve plunger does not return, replace fuel filler neck, then go to step  23. If fuel overflow limiter valve plunger is okay, reinstall fuel cap and go to next step.
  18. Connect EVAP system pressure pump to fuel filler neck. Set EVAP system pressure pump pressure/hold valve to OPEN and vent valve to CLOSED. Turn pump timer on. Check for air passing through air filter in ventilation solenoid vent hose. See Fig 1. If air passes through filter, go to step  23. If air does not pass through filter, go to next step.
  19. Check ventilation solenoid vent hose air filter for clogging. If problem exists, replace as necessary, then go to step  23. If problem does not exist, go to next step.
  20. Using hand vacuum pump, check hoses "G" through "K" for clogging. See Figure and Fig 2 . If problem exists, replace hose(s) as necessary, then go to step  23. If problem does not exist, go to next step.
  21. Disconnect hose "G" from EVAP canister. Connect hand vacuum pump to EVAP canister port from which hose "G" was removed. Disconnect hoses "F" and "H" from EVAP canister and plug canister ports. Apply vacuum. Unplug each port in turn. Vacuum should leak out of each port. If vacuum leaks out of each port, reconnect hoses, then go to next step. If vacuum does not leak out of both ports, replace EVAP canister, then go to step  23.
  22. Lower EVAP canister assembly. Disconnect hose "G" from ventilation solenoid. See Figure. Connect hand vacuum pump to ventilation solenoid port from which hose "G" was removed. Turn ignition on. Apply vacuum. Vacuum should leak. Using scan tool, select actuator test No. 29 (ventilation solenoid). Apply vacuum. Vacuum should hold. If ventilation solenoid performs as specified, go to next step. If ventilation solenoid operates, but does not hold or leak vacuum as specified, replace ventilation solenoid, then go to step  23. If ventilation solenoid does not operate, check ventilation solenoid circuit. See DTC P0446: EVAPORATIVE EMISSION (EVAP) CONTROL SYSTEM VENTILATION SOLENOID CIRCUIT MALFUNCTION .
  23. Remove fuel tank. Using hand vacuum pump, check hoses "L", "M" and "N" for clogging. See Figure. If problem exists, replace hose(s) as necessary, install fuel tank, then go to next step. If problem does not exist, install fuel tank, then go to next step.
  24. Using scan tool, clear DTCs. Test drive vehicle following EVAP system leak monitor drive cycle pattern. See OBD-II DRIVE CYCLES under VERIFYING REPAIRS in SELF-DIAGNOSTICS - INTRODUCTION article. Check for DTCs. Confirm DTC P0450 does not reset. See VERIFYING REPAIRS in SELF-DIAGNOSTICS - INTRODUCTION article.
Fig 1: Locating EVAP System Air Filter
G99H54178Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Fig 2: Locating Hoses "F", "G" & "H"
G99B54180Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.