LEMON Manuals: Even more car manuals for everyone

Engine 4.6L: Installation: Engine: Installation

  1. Using the special tool, install the engine assembly in the vehicle.
    Fig 1: Installing Engine Assembly In Vehicle
    G02754615Courtesy of FORD MOTOR CO.
  2. Remove the special tools.
  3. Raise the vehicle. For additional information, refer to JACKING & LIFTING .
  4. NOTE: When vehicle is raised, verify that the torque converter is correctly seated.
    Fig 2: Installing Bolts And Stud
    G02754616Courtesy of FORD MOTOR CO.
  5. Install the four bolts and one stud.
  6. Connect the electrical connectors.
    Fig 3: Connecting Electrical Connectors
    G02754617Courtesy of FORD MOTOR CO.
  7. Using the special tool, install the LH heated oxygen sensor.
    Fig 4: Installing LH Heated Oxygen Sensor
    G02754618Courtesy of FORD MOTOR CO.
  8. Connect the LH heated oxygen sensor electrical connector.
    Fig 5: Connecting LH Heated Oxygen Sensor Electrical Connector
    G02754619Courtesy of FORD MOTOR CO.
  9. Install the engine insulator mount nuts.
    Fig 6: Installing Engine Insulator Mount Nuts
    G02754620Courtesy of FORD MOTOR CO.
  10. Install the four torque converter nuts.
    • Rotate the crankshaft to access the nuts.
    Fig 7: Installing Four Torque Converter Nuts
    G02754621Courtesy of FORD MOTOR CO.
  11. Install the rubber access plug.
    Fig 8: Installing Rubber Access Plug
    G02754622Courtesy of FORD MOTOR CO.
  12. Install the inspection cover and the bolts.
    Fig 9: Installing Inspection Cover Bolts
    G02754623Courtesy of FORD MOTOR CO.
  13. Install the starter motor and the bolts.
    Fig 10: Installing Starter Motor Bolts
    G02754624Courtesy of FORD MOTOR CO.
  14. Connect the starter electrical connections and install the nuts.
    • Install the solenoid terminal cover.
    Fig 11: Connecting Starter Electrical Connections
    G02754625Courtesy of FORD MOTOR CO.
  15. Position the exhaust, install the four nuts and remove the support.
    Fig 12: Installing Nuts
    G02754626Courtesy of FORD MOTOR CO.
  16. Install the power steering pump and the bolts.
    Fig 13: Installing Power Steering Pump Bolts
    G02754627Courtesy of FORD MOTOR CO.
  17. Install the A/C compressor and the bolts.
    Fig 14: Installing A/C Compressor Bolts
    G02754628Courtesy of FORD MOTOR CO.
  18. Connect the A/C compressor electrical connector.
    Fig 15: Connecting A/C Compressor Electrical Connector
    G02754629Courtesy of FORD MOTOR CO.
  19. Connect the engine wiring harness retainers to the A/C compressor.
    Fig 16: Connecting Engine Wiring Harness Retainers
    G02754630Courtesy of FORD MOTOR CO.
  20. Connect the crankshaft position (CKP) sensor electrical connector.
    Fig 17: Connecting Crankshaft Position Sensor Electrical Connector
    G02754631Courtesy of FORD MOTOR CO.
  21. Position the transmission oil cooler tubes and install the bolt.
    Fig 18: Installing Bolt
    G02754632Courtesy of FORD MOTOR CO.
  22. Install the transmission cooler tube support bracket.
    Fig 19: Installing Transmission Cooler Tube Support Bracket
    G02754633Courtesy of FORD MOTOR CO.
  23. Install the power steering line bracket.
    Fig 20: Installing Power Steering Line Bracket
    G02754634Courtesy of FORD MOTOR CO.
  24. Connect the power steering pressure (PSP) switch electrical connector.
    Fig 21: Connecting Power Steering Pressure Switch Electrical Connector
    G02754635Courtesy of FORD MOTOR CO.
  25. Connect the power steering electrical connector.
    Fig 22: Connecting Power Steering Electrical Connector
    G02754636Courtesy of FORD MOTOR CO.
  26. Connect the electrical connector.
    Fig 23: Connecting Electrical Connector
    G02754637Courtesy of FORD MOTOR CO.
  27. Lower the vehicle.
  28. Install the bolts.
    Fig 24: Installing Bolts
    G02754638Courtesy of FORD MOTOR CO.
  29. Install the cooling fan. For additional information, refer to ENGINE COOLING .
  30. NOTE: Do not reuse hose clamps. Use appropriately sized worm-style clamps in place of the constant tension clamps.
    Fig 25: Connecting Lower Radiator Hose
    G02754639Courtesy of FORD MOTOR CO.
  31. Connect the lower radiator hose.
  32. Connect the upper radiator hose to the hose connection.
    Fig 26: Connecting Upper Radiator Hose
    G02754640Courtesy of FORD MOTOR CO.
  33. Install the power steering reservoir.
    Fig 27: Installing Power Steering Reservoir
    G02754641Courtesy of FORD MOTOR CO.
  34. Connect the engine bulkhead connectors.
    Fig 28: Connecting Engine Bulkhead Connectors
    G02754642Courtesy of FORD MOTOR CO.
  35. Position the ground strap and install the bolt.
    Fig 29: Installing Bolt
    G02754643Courtesy of FORD MOTOR CO.
  36. NOTE: Do not reuse hose clamps. Use appropriately sized worm-style clamps in place of the constant tension clamps.
    Fig 30: Connecting Heater Hoses
    G02754644Courtesy of FORD MOTOR CO.
  37. Connect the heater hoses.
  38. Connect the A/C low charge protection switch electrical connector.
    Fig 31: Connecting A/C Low Charge Protection Switch Electrical Connector
    G02754645Courtesy of FORD MOTOR CO.
  39. Connect the A/C electrical connector.
    Fig 32: Connecting A/C Electrical Connector
    G02754646Courtesy of FORD MOTOR CO.
  40. Connect the power distribution power supply electrical connector.
    Fig 33: Connecting Power Distribution Power Supply Electrical Connector
    G02754647Courtesy of FORD MOTOR CO.
  41. Install the electrical connection cover.
    Fig 34: Installing Electrical Connection Cover
    G02754648Courtesy of FORD MOTOR CO.
  42. Connect the electrical connectors.
    Fig 35: Connecting Electrical Connectors
    G02754649Courtesy of FORD MOTOR CO.
  43. Install the ground strap.
    Fig 36: Installing Ground Strap
    G02754650Courtesy of FORD MOTOR CO.
  44. Connect the fuel line spring lock coupling. For additional information, refer to FUEL SYSTEM-GENERAL INFORMATION .
  45. Install the accelerator cable and the speed control actuator cable to the clips.
    Fig 37: Connecting Fuel Line Spring Lock Coupling
    G02754651Courtesy of FORD MOTOR CO.
  46. Connect the accelerator cable and the speed control actuator cable.
    • Install the bolts.
    • Connect the cables.
    Fig 38: Connecting Accelerator Cable And Speed Control Actuator Cable
    G02754652Courtesy of FORD MOTOR CO.
  47. Connect the three hoses and the canister purge valve electrical connection.
    Fig 39: Connecting Hoses And Canister Purge Valve Electrical Connection
    G02754653Courtesy of FORD MOTOR CO.
  48. Connect the vacuum hose.
    Fig 40: Connecting Vacuum Hose
    G02754654Courtesy of FORD MOTOR CO.
  49. Install the air cleaner and outlet pipe. For additional information, refer to INTAKE AIR DISTRIBUTION & FILTERING .
  50. Install the accessory drive belt. For additional information, refer to SPECIFICATIONS & DRIVE BELT ROUTING .
  51. Install the support bracket.
    Fig 41: Installing Support Bracket
    G02754655Courtesy of FORD MOTOR CO.
  52. Install the wiper mounting arm and pivot shaft. For additional information, refer to WIPERS AND WASHERS .
  53. Fill the crankcase with clean engine oil.
  54. Connect both battery cables.
  55. Fill and bleed the cooling system. For additional information, refer to ENGINE COOLING .
  56. Install the hood.