LEMON Manuals: Even more car manuals for everyone

Timing Drive Components: Installation

    ENGINES WITH RATCHETING TIMING CHAIN TENSIONERS 

    CAUTION: Timing chain procedure must be followed exactly or damage to valves and pistons will result.
    CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
    NOTE: LH shown, RH similar.
    Fig 1: Compressing Tensioner Plunger
    G02754100Courtesy of FORD MOTOR CO.
  1. Compress each tensioner plunger, using an edge of a vise.
  2. Using a small screwdriver or pick, push back and hold the ratchet mechanism.
    Fig 2: Holding Ratchet Mechanism
    G02754101Courtesy of FORD MOTOR CO.
  3. While holding the ratchet mechanism, push the ratchet arm back into the tensioner housing.
    Fig 3: Pushing Ratchet Arm Back Into Tensioner Housing
    G02754102Courtesy of FORD MOTOR CO.
  4. Install a paper clip into the hole of each tensioner housing to hold the ratchet assembly and plunger in during installation.
    • Remove the tensioner from the vise.
    Fig 4: Removing Tensioner From Vise
    G02754103Courtesy of FORD MOTOR CO.
  5. ENGINES WITH NON-RATCHETING TIMING CHAIN TENSIONERS 

    CAUTION: If one or both tensioner mounting bolts are loosened or removed, the tensioner-sealing bead must be inspected for seal integrity. Any cracks, tears, cuts or separation from the tensioner body or permanent compression of the seal bead, will require replacement of the tensioner.
  6. Inspect the RH and LH timing chain tensioners.
    • Install new tensioners as necessary.
  7. CAUTION: The timing chain procedure must be followed exactly or damage to valves and pistons will result
    NOTE: LH shown, RH similar.
    Fig 5: Compressing Tensioner Plunger
    G02754104Courtesy of FORD MOTOR CO.
  8. Compress each tensioner plunger, using a vise.
  9. Install a retaining clip on each tensioner to hold the plunger in during installation.
    Fig 6: Installing Retaining Clip
    G02754105Courtesy of FORD MOTOR CO.
  10. ALL ENGINES 

  11. If the copper links are not visible, mark one link on one end and one link on the other end, and use as timing marks.
    Fig 7: Identifying Timing Mark
    G02754106Courtesy of FORD MOTOR CO.
  12. Install the camshaft sprockets and new bolts. Tighten the bolts in two stages.
    • Stage 1: Tighten the bolt to 40 Nm (30 lb-ft).
    • Stage 2: Tighten the bolt an additional 90 degrees (1/4 turn).
    Fig 8: Installing Camshaft Sprockets Bolts
    G02754107Courtesy of FORD MOTOR CO.
  13. Using the special tool, position the crankshaft so the number one cylinder is at top dead center (TDC).
    Fig 9: Positioning Crankshaft Number One Cylinder Is At Top Dead Center
    G02754108Courtesy of FORD MOTOR CO.
  14. Install the crankshaft sprocket, making sure the flange faces forward.
    Fig 10: Installing Crankshaft Sprocket
    G02754109Courtesy of FORD MOTOR CO.
  15. Install the timing chain guide.
    1. Position the LH timing chain guide.
    2. Install and tighten the LH bolts.
    3. Position the RH timing chain guide.
    4. Install and tighten the RH bolts.
    Fig 11: Installing Timing Chain Guide
    G02754110Courtesy of FORD MOTOR CO.
  16. Rotate the RH camshaft sprocket until the timing mark is approximately at the 11 o'clock position.

    Rotate the LH camshaft sprocket until the timing mark is approximately at the 12 o'clock position.

    Fig 12: Identifying Timing Mark
    G02754111Courtesy of FORD MOTOR CO.
  17. Position the LH (inner) timing chain on the crankshaft sprocket, aligning the copper (marked) link with the timing mark on the sprocket.
    Fig 13: Aligning Copper Marked Link With Timing Mark On Sprocket
    G02754112Courtesy of FORD MOTOR CO.
  18. Install the LH timing chain on the sprocket, aligning the copper (marked) link with the timing marks on the sprocket.
    Fig 14: Aligning Copper Marked Link With Timing Marks On Sprocket
    G02754113Courtesy of FORD MOTOR CO.
  19. NOTE: The LH timing chain tensioner arm has a bump near the dowel hole for identification.
    Fig 15: Installing LH Timing Chain Tensioner
    G02754114Courtesy of FORD MOTOR CO.
  20. Position the LH timing chain tensioner arm on the dowel pin and install the LH timing chain tensioner.
  21. ENGINES WITH RATCHETING TIMING CHAIN TENSIONERS 

  22. Remove the retaining clip from the LH timing chain tensioner.
    Fig 16: Removing Retaining Clip
    G02754115Courtesy of FORD MOTOR CO.
  23. ENGINES WITH NON-RATCHETING TIMING CHAIN TENSIONERS 

  24. Remove the retaining clip from the LH timing chain tensioner.
    Fig 17: Removing Retaining Clip
    G02754116Courtesy of FORD MOTOR CO.
  25. ALL ENGINES 

  26. Position the RH (outer) timing chain on the crankshaft sprocket, aligning the copper (marked) link with the timing mark on the sprocket.
    Fig 18: Aligning Copper Marked Link With Timing Mark On Sprocket
    G02754117Courtesy of FORD MOTOR CO.
  27. Install the RH timing chain on the camshaft sprocket, aligning the copper (marked) link with the timing marks on the sprocket.
    Fig 19: Aligning Copper Marked Link With Timing Marks On Sprocket
    G02754118Courtesy of FORD MOTOR CO.
  28. Position the RH timing chain tensioner arm on the dowel pin and install the RH timing chain tensioner.
    Fig 20: Installing RH Timing Chain Tensioner
    G02754119Courtesy of FORD MOTOR CO.
  29. ENGINES WITH RATCHETING TIMING CHAIN TENSIONERS 

  30. Remove the retaining clip from the RH timing chain tensioner.
    Fig 21: Removing Retaining Clip
    G02754120Courtesy of FORD MOTOR CO.
  31. ENGINES WITH NON-RATCHETING TIMING CHAIN TENSIONERS 

  32. Remove the retaining clip from the RH timing chain tensioner.
    Fig 22: Removing Retaining Clip
    G02754121Courtesy of FORD MOTOR CO.
  33. ALL ENGINES 

  34. Make sure that the copper (marked) chain links are lined up with the dots on the crankshaft sprocket and the camshaft sprockets.
    Fig 23: Identifying Copper Marks
    G02754122Courtesy of FORD MOTOR CO.
  35. Rotate the camshaft until the lobe is in the up position.
    Fig 24: Rotating Camshaft
    G02754123Courtesy of FORD MOTOR CO.
  36. Install the special tool between the valve spring coils to prevent valve stem seal damage.
    Fig 25: Installing Special Tool
    G02754124Courtesy of FORD MOTOR CO.
  37. NOTE: Lubricate the camshaft roller followers using clean engine oil.
    Fig 26: Installing Camshaft Roller Followers
    G02754125Courtesy of FORD MOTOR CO.
  38. Install the camshaft roller followers.
    1. Install the special tool.
    2. Compress the valve spring.
    3. Install the camshaft roller followers in their original locations.
  39. Install the eight spark plugs.
    Fig 27: Installing Spark Plugs
    G02754126Courtesy of FORD MOTOR CO.
  40. Install the eight ignition coils and bolts.
    Fig 28: Installing Ignition Coils Bolts
    G02754127Courtesy of FORD MOTOR CO.
  41. Connect the eight ignition coil electrical connectors.
    Fig 29: Connecting Ignition Coil Electrical Connectors
    G02754128Courtesy of FORD MOTOR CO.
  42. Install the crankshaft sensor ring on the crankshaft.
    Fig 30: Installing Crankshaft Sensor Ring On Crankshaft
    G02754129Courtesy of FORD MOTOR CO.
  43. Install the engine front cover. For additional information, refer to ENGINE FRONT COVER .