LEMON Manuals: Even more car manuals for everyone

Service Campaign 2020080013 Clean SRS Control Unit Contacts (P-SC-2020080013)

WARNING: This page is about the A220 4Matic, which is a different variant/trim than selected.
Publication date: 2020-09-04
Reference number: P-SC-2020080013
Supersedes refnos: 2020080013

SERVICE CAMPAIGN 2020080013 CLEAN SRS CONTROL UNIT CONTACTS

SERVICE CAMPAIGN 2020080013 CLEAN SRS CONTROL UNIT CONTACTS

SERVICE CAMPAIGN BULLETIN

Reference Number(s): P-SC-2020080013, Date of Issue:  September 04, 2020
MERCEDES-BENZ: MY19-21 118, 177, 247 (CLA-Class, A-Class, GLA-Class GLB-Class)

SERVICE INFORMATION

IMPORTANT NEW SERVICE CAMPAIGN LAUNCH INFORMATION 

IN-VEHICLE NOTIFICATION 

To enhance the Mercedes-Benz customer experience, an in-vehicle notification will be sent to the affected vehicles for this service campaign. The notification will be sent to approximately 6,000 VINs per week. An example of the message that will appear in a flagged vehicle is shown below.

This message will appear at engine start beginning September 7, 2020 and will continue every 30 days until the service campaign has been completed. Dealers are reminded to submit warranty claims in a timely manner to reduce the possibility of redundant messages.

G13223177

Please note that all customer inquiries should be directed to the Customer Assistance Center at 1-800-FOR-MERCEDES.

Sincerely,

Gregory Gunther

Department Manager, Vehicle Compliance & Analysis

G13223178

Campaign No. 2020080013, September 2020

TO: ALL MERCEDES-BENZ CENTERS

SUBJECT

Model CLA-Class, A-Class, GLA-Class and GLB-Class (118, 177, and 247 platform) Model Year 2019-2021 

Clean SRS Control Unit Contacts 

Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz, has determined that on certain MY19-21 CLA-Class, A-Class, GLA-Class and GLB-Class (118, 177, and 247 platform) vehicles, an increased electrical resistance may occur between the connector block of the electronic control unit and the connector pins for the Supplemental Restraint System (SRS) wiring harness. The SRS control unit might detect the increased resistance in various SRS circuits (e.g. driver/front passenger airbag, seat belt tensioner) which could lead to illumination of a warning message (yellow) and a warning lamp (red) in the instrument cluster. The functionalities of the SRS system are not impaired. MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will inspect and clean the SRS control unit connector contacts. Customers included in this Service Campaign will be notified through in-vehicle notification in waves of approx. 6000 per week with subsequent notices sent every 30 days.

Prior to performing this Campaign:

Approximately 38,627 vehicle is affected.

Order No. P-SC-2020080013

This bulletin has been created and maintained in accordance with MBUSA-SLP S423QH001, Document and Data Control, and MBUSA-SLP S424HH001, Control of Quality Records.

Test tool must be prepared before the work procedure. 

See description "Preparation of test tool" on page 9 and 10.

Before beginning work, no SRS fault message may be present  in the instrument cluster!

If a SRS fault message is present before the start of work, it must be rectified.

The fault rectification may not be invoiced together with the campaign.

WORK PROCEDURE

  1. Disconnect ground line of on-board electrical system battery.

    For basic data, see AR54.10-P-0003MFA  .

  2. Fold away left and right floor covering in area of center console and place powertrain control unit (A, figure 1)  with connected lines to one side.

    For basic data on control unit removal, see AR91.60-P-0615MFA  .

    Contrary to the work instructions in WIS, the center console does not have to be disassembled.

    G13223179
  3. Disconnect the contacts of both electrical connectors (20 - and 104-pin)  of the Supplemental Restraint System control unit (SRS) (figures 2 - 4)  .

    To release the 20-pin plug, push the red locking clip (B, figure 2)  in the direction of the arrow.

    To disconnect the 20-pin plug (C, figure 3), press the lock downwards (in direction of the arrow)  by using an allen wrench.

    G13223180
  4. Release three nuts (D, figure 4)  for the Supplemental Restraint System control unit (SRS)  and remove this.
    G13223181
  5. Place Supplemental Restraint System control unit (SRS)  on the ESD  mat for processing at the workplace.

    The contacts of the Supplemental Restraint System control unit (SRS)  may not be touched.

  6. Clean all electrical connection pins in the control unit with extreme caution  by means of cleaning brushes (C, figures 5 and 6)  .

    6 cleaning brushes (figures 7)  . For the complete cleaning procedure a total of six cleaning brushes must be used.

    G13223182
    G13223183
    G13223184

    Observe the information on preventing damage to the electronic components due to electrostatic discharge AH54.00-P-0001-01A. 

    Ensure extreme cleanliness.

    Slide cleaning brushes in insertion direction onto the connection pins up to end stop and remove again (figures 5 and 6). 

    The cleaning brushes must be placed parallel to the lower edge of the control unit (Figures 5, 6 and 8). 

    An insertion of the cleaning bushes 90° offset to the lower edge of the control unit can result in damage to the connection pins (figures 9 and 10). 

    All movements at the connectors must be executed in a linear manner in order to not damage (bend)  the pins.

    Do not twist.  A twisting of the cleaning brush can damage or bend the adjacent contacts.

    Up to two  connection pins can be cleaned simultaneously.

    All connection pins must be cleaned. No connection pins may be omitted.

    Observe the cleaning sequence in operation step 7. 

  7. Perform cleaning in the following sequence: 

    The SRS control unit has 4 connection rows (1-4 figure 9). 

    A total of 6 cleaning brushes  are required for the complete cleaning process.

    • Connection rows 1 and 2  must be fully  cleaned with a cleaning brush. Repeat this process two more times with a new cleaning brush for each time.
    • Connection rows 3 and 4  must be fully  cleaned with a cleaning brush. Repeat this process two more times with a new cleaning brush for each time.

    Each contact is thus cleaned three times.

    No cleaning agents  or similar may be used with the cleaning brush.

    G13223185
    G13223186
    G13223187

    Check for damage after cleaning: 

  8. Slide on  the test coupling (104-pin and 20-pin)  from above onto the cleaned SRS control unit without any force  up to the end stop and remove the test coupling (figure 11 and 12). 

    The objective is to detect with this empty coupling housing whether the pins are OK and not bent after the cleaning.

    If both test couplings can be inserted without any force up to the end stop (see F and G figures 11 and 12), the pins are OK.

    In the case of damaged control unit pins, the SRS control unit is unusable and must be replaced (dispose of the control unit properly). 

    The contact carriers must be fully inserted in the support body of the coupling housing and align with the control unit edge (F, figure 11). 

    The support body of the 20-pin male test connector must align with the control unit edge (G, figure 12). 

    The test tools can be reused (see annex "Preparation of test tool" on page 9. 

    G13223188
    G13223189
  9. Visual inspection of the pins in the control unit (figure 13). 

    No control unit pins may be bent.

    In the case of damaged control unit pins, the SRS control unit is unusable and must be replaced.

    For basic data, see AR91.60-P-0615MFA. 

    G13223190
  10. Make the used cleaning bushes unusable at the end of the cleaning work (figure 14)  .

    Cleaning brushes may not be reused. 

    G13223191
  11. Assemble in reverse order.

    First tighten the SRS control unit with the correct torque ( Nm 10) and then connect.

    For basic data, see AR91.60-P-0615MFA  .

  12. Switch ignition to position 1  . To do so, press start button once without touching the brake pedal. Check whether airbag indicator lamp (H, figure 15)  permanently goes off after a few seconds.

The SRS check is thus completely ensured.

G13223192

PREPARATION OF TEST TOOL

The test tools (104-pin and 20-pin) must only be produced once per workshop  and reused. The test tools must be stored in a clean, dry, and secure location. 

A visual inspection must be carried out before every use. As soon as contamination or damage is noticeable, this test tool must be replaced by a new one. Dispose of the old test tool.

  1. Remove retaining bracket (figure 16)  from coupling housing (A 029 545 90 26)  and dispose of it.
    G13223193
  2. Insert both contact carriers with low effort  into the coupling housing up to the end stop (figure 17). 

    Retaining lugs of contact carriers must engage.

    G13223194
  3. Assemble airbag control unit coupling housing (A 166 545 04 26)  and contact carrier (A 005 545 23 40) (figure 18 and 19). 

    Insert contact carrier (yellow)  of 20-pin plug with low effort  in coupling housing (black) up to

    G13223195
    G13223196
  4. Carefully remove locking clip (red)  and engagement lever (black)  from the plug housing and subsequently dispose of (figure 20)  .
G13223197

SPECIAL TOOLS

PARTS INFORMATION

Qty. Part Name Part Number
1 ESD kit W 000 589 52 98 00

PARTS

PARTS INFORMATION

Qty. Part Name Part Number
6 Cleaning bush A 000 540 38 04

TEST TOOL PARTS INFORMATION

PARTS INFORMATION

Qty. Part Name Part Number
1(1) Coupling housing A 029 545 90 26
1(1) Contact carrier A 005 545 53 40
1(1) Contact carrier A 005 545 54 40
1(1) Airbag control unit coupling housing A 166 545 04 26
1(1) Contact carrier A 005 545 23 40
(1) Test tool may only be ordered and claimed once per workshop and be reused for subsequent repairs.

WARRANTY INFORMATION

Operation:  Clean pins at control unit (SRS)(02-1056)

Includes:  Disconnect and reconnect the battery.

WARRANTY INFORMATION

Damage Code Operation Number Labor Time (hrs.)
91 921 08 7 02-1056 0.6
NOTE: Operation Number labor times are subject to change.