LEMON Manuals: Even more car manuals for everyone

Remove/install starter - AR15.30-P-7100GZS

ENGINES 156 in MODEL 164, 251 

Fig 1: Identifying Starter Remove/Install Components
G10115381Courtesy of MERCEDES-BENZ USA
MODIFICATION NOTES

4.8.10 Method to install engine hoist changed AR33.10-P-0100-01RT
REMOVINGINSTALLING Remove/install     
DANGER Risk of injury  caused by fingers being pinched or crushed  when removing, installing or aligning hoods, doors, trunk lids, liftgates or sliding roof Keep body parts and limbs well clear of moving parts. AS00.00-Z-0011-01A
DANGER Risk of death  caused by vehicle slipping or toppling off of the lifting platform. Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer. AS00.00-Z-0010-01A
DANGER Risk of explosion  caused by escaping oxyhydrogen gas. Risk of injury  caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte (contains diluted sulfuric acid) or metal spatter due to short circuit. Risk of burn injuries  caused by short circuit. Risk of poisoning  caused by swallowing battery electrolyte (contains diluted sulfuric acid) or absorption of lead over the skin or orifices No fire, sparks, open flames or smoking. Wear acid-resistant gloves and clothing and safety glasses with side guards.
Do not place any conductive objects on the battery and avoid any short circuit from battery positive to ground.
Only fill liquid battery electrolyte (diluted sulfuric acid) into suitable and appropriately marked containers.
AS54.10-Z-0001-01A
1 Disconnect ground line from battery NOTES Insulate ground line clamp as a protection against unintentional contact of ground line with ground point of battery.  
    Model 164 AR54.10-P-0003GZ
    Model 251 AR54.10-P-0003RT
NOTES Notes on battery All models AH54.10-P-0001-01A
2 Open engine hood Model 164 AR88.40-P-1000GZ
Model 251 AR88.40-P-1000RT
3 Remove partition wall between wheel wells IMPORTANT Only model 251. AR62.30-P-2400RT
4 Remove air filter housing NOTES Do not tilt front engine cover, but lift upwards vertically otherwise the retaining lugs can break off. AR09.10-P-1150GZS
5 Mount engine lifting device Model 164 AR33.10-P-0100-01GZ
Model 251
IMPORTANT Observe manufacturer's assembly specifications and safety information.
AR33.10-P-0100-01RT
TORQUE SPECIFICATION Model 251 *BA62.30-P-1008-01E 
SPECIAL TOOL Engine hoist Figure
6 Raise vehicle with vehicle lift Model 164 AR00.60-P-1000GZ
Model 251 AR00.60-P-1000RT
7 Remove bottom engine compartment paneling Model 164 AR61.20-P-1105GZ
Model 251 AR61.20-P-1105RT
8 Remove exhaust system up to rear flange connection IMPORTANT Do not completely remove exhaust system, instead separate at rear flange connection.
Model 164: ↓
 
Remove/install exhaust system complete.
Model 251: ↓
AR49.10-P-7000GZ
Remove/install exhaust system complete. AR49.10-P-7000GZS
9 Remove engine mount with engine support at right front   AR22.10-P-1260GZS
10 Remove protection against accidental contact for electrical line for circuit 30 (1) on starter (M1)    
11 Detach electrical line for circuit 30 (1) at starter (M1) TORQUE SPECIFICATION *BA15.30-P-1001-01O 
12 Detach electrical line for circuit 50 (2) at starter (M1) TORQUE SPECIFICATION *BA15.30-P-1002-01O 
13 Detach bracket for automatic oil lines at oil pan TORQUE SPECIFICATION *BA01.45-P-1005-01R 
14 Remove bolts (7) of starter (M1) TORQUE SPECIFICATION *BA15.30-P-1003-01O 
15 Lead starter (M1) down and out    
16 Check ring gear at the drive plate for wear and damage IMPORTANT When replacing starter (M1).
IMPORTANT Rotate engine at center bolt of crankshaft in the direction of rotation.
 
17 Install in the reverse order    
STARTER

Number Designation Engine 156
BA15.30-P-1001-01O Nut, connection for circuit 30 Nm 15
BA15.30-P-1002-01O Nut, connection for circuit 50 Nm 8
BA15.30-P-1003-01O Bolt connecting starter to crankcase Nm 40
OIL PAN

Number Designation Engine 156
BA01.45-P-1005-01R Bracket, oil lines to oil pan M6 Nm 5
CROSSMEMBER AND FRONT REINFORCEMENT

Number Designation Model 251
BA62.30-P-1008-01E Bolt for partition wall reinforcement between wheel well liners to fender Nm 10
Fig 2: Identifying Engine Lifting Fixture (240 589 00 61 00)
G07279162Courtesy of MERCEDES-BENZ USA