Remove/install starter - AR15.30-P-7100GZB
ENGINES 642 in MODEL 164, 251
MODIFICATION NOTES
| 4.8.10 | Method to install engine hoist changed | AR33.10-P-0100-01RT |
| Remove/install | |||
| Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer. | AS00.00-Z-0010-01A | |
| Notes on self-locking nuts and bolts | AH00.00-N-0001-01A | ||
| Risk of explosion caused by escaping oxyhydrogen gas. Risk of injury caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte (contains diluted sulfuric acid) or metal spatter due to short circuit. Risk of burn injuries caused by short circuit. Risk of poisoning caused by swallowing battery electrolyte (contains diluted sulfuric acid) or absorption of lead over the skin or orifices | No fire, sparks, open flames or smoking. Wear acid-resistant gloves and clothing and safety glasses with side guards. Do not place any conductive objects on the battery and avoid any short circuit from battery positive to ground. Only fill liquid battery electrolyte (diluted sulfuric acid) into suitable and appropriately marked containers. |
AS54.10-Z-0001-01A | |
| 1 | Detach ground line from battery | ||
| Model 164 | AR54.10-P-0003GZ | ||
| Model 251 | AR54.10-P-0003RT | ||
| Notes on battery | All models | AH54.10-P-0001-01A | |
| 2 | Remove bottom sections of soundproofing | Model 164 | AR94.30-P-5300GZ |
| Model 251 | AR94.30-P-5300RT | ||
| 3 | Unscrew nut (1) and remove starter shield (3) | ||
| *BA15.30-P-1004-01N | |||
| 4 | Unclip electrical line (2) at engine mount shield (5) | ||
| 5 | Remove bolt (4) for right engine mount | ||
| Vehicles with 4MATIC | AR22.10-P-1100GZB | ||
| Vehicles without 4MATIC | AR22.10-P-1100RTB | ||
| 6 | Remove engine mount shield (5) from above | ||
| 7 | Remove bolts (8) | *BA15.30-P-1003-01N | |
| 8 | Mount engine lifting device | Only for starter (M1) from Valeo | |
| Model 164 | AR33.10-P-0100-01GZ | ||
| Model 251 |
AR33.10-P-0100-01RT | ||
| *BA62.30-P-1008-01E | |||
| Figure | |||
| 9 | Lift engine with engine support bracket | Only for starter (M1) from Valeo |
|
| 10 | Remove bolts on front axle carrier and remove right engine mount | Only for starter (M1) from Valeo To do this push starter (M1) upwards. | |
| Vehicles with 4MATIC | AR22.10-P-1100GZB | ||
| Vehicles without 4MATIC | AR22.10-P-1100RTB | ||
| 11 | Remove protection against accidental contact (6) of circuit 30 electrical line from starter (M1) | ||
| 12 | Detach electrical line circuit 30 (M1) from starter | *BA15.30-P-1001-01N | |
| 13 | Disconnect electrical line of circuit 50 (7) from starter (M1) | *BA15.30-P-1002-01N | |
| 14 | Remove starter (M1) from below | ||
| 15 | Check ring gear for wear and check for damage | When replacing the starter (M1). |
|
| 16 | Install in the reverse order |
STARTER
| Number | Designation | Engine 642 | |
|---|---|---|---|
| BA15.30-P-1001-01N | Nut, connection for circuit 30 | Nm | 14 |
| BA15.30-P-1002-01N | Nut, connection for circuit 50 | Nm | 6 |
| BA15.30-P-1003-01N | Bolt, starter to cylinder crankcase | Nm | 40 |
| BA15.30-P-1004-01N | Shield to starter | Nm | 9 |
CROSSMEMBER AND FRONT REINFORCEMENT
| Number | Designation | Model 251 | |
|---|---|---|---|
| BA62.30-P-1008-01E | Bolt for partition wall reinforcement between wheel well liners to fender | Nm | 10 |