LEMON Manuals: Even more car manuals for everyone

Function Inspection Using M-MDS

P0171-00: (PCM (SKYACTIV-G)) DIAGNOSTIC PROCEDURE

Step Inspection Results Action
1 PURPOSE: VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY 
  • Verify related Service Bulletins, on-line repair information, or Service Information availability.
  • Is any related Information available?
Yes Perform repair or diagnosis according to the available information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
2 PURPOSE: IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA 
  • Is the DTC P0171-00: on freeze frame data?
Yes Go to the next step.
No Go to the troubleshooting procedure for DTC on freeze frame data.
(See DTC TABLE [PCM (SKYACTIV-G)] .)
3 PURPOSE: RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION 
  • Record the freeze frame data/snapshot data.
    NOTE:
    • Recording can be facilitated using the screen capture function of the PC.
- Go to the next step.
4 PURPOSE: VERIFY IF INPUT SIGNAL TO PCM AFFECTS FUEL INJECTION 
Yes Inspect the suspected sensor and related wiring harness.
  • If there is any malfunction:
    • Repair or replace the malfunctioning location.
    • Go to Troubleshooting Diagnostic Procedure to perform the repair completion verification 1.
  • If there is no malfunction:
    • Go to the next step.
No Go to the next step.
5 PURPOSE: VERIFY CONNECTOR CONNECTIONS 
  • Start the engine.
  • Access the following PIDs using the M-MDS: (See PID/DATA MONITOR INSPECTION .)
    • FUEL_PRES
    • FUEL_PUMP_REQ
    • PRG_DUTY
    • MAF
    • MAP
    • MAP_VOLT
    • IAT2
    • VLV_TIMING_ACT_EX
    • VLV_TIMING_ACT_IN
  • Does the PID value fluctuate when the following connectors are shaken?
    • Fuel pressure sensor
    • Fuel pump
    • Purge solenoid valve
    • MAF sensor
    • MAP sensor/IAT sensor No. 2
    • OCV
    • Electric variable valve timing motor/driver
    • PCM
Yes Repair or replace the applicable connector parts.
Go to Troubleshooting Diagnostic Procedure to perform the repair completion verification 1.
No Go to the next step.
6 PURPOSE: VERIFY FUEL PRESSURE (HIGH-SIDE) MALFUNCTION 
  • Switch the ignition off.
  • Reconnect all disconnected connectors.
  • Start the engine and warm it up completely.
  • Access the PCM PID [FUEL_PRES] using the M-MDS.

    (See PID/DATA MONITOR INSPECTION .)

  • Is the [FUEL_PRES] PID value approx. 10 MPa {102 kgf/cm2 , 1450 psi}?
Yes Go to the next step.
No [FUEL_PRES] value is lower than 10 MPa {102 kgf/cm2 , 1450 psi}:
  • Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 1.

[FUEL_PRES] value is higher than 10 MPa {102 kgf/cm2 , 1450 psi}:
  • Go to Step 8.
7 PURPOSE: VERIFY FUEL PRESSURE (LOW-SIDE) MALFUNCTION 
NOTE:
  • Verify the fuel pressure on the low pressure side with the operation of the high pressure fuel pump turned off.
  • Bleed the remaining pressure in the fuel line using the following procedure.
    1. Switch the ignition off.
    2. Disconnect the high pressure fuel pump connector.
    3. Remove the fuel pump relay. (Refer to RELAY LOCATION in service information.)
    4. Start the engine and wait until the engine stalls.
  • Switch the ignition off.
  • Install the fuel pump relay.
  • Switch the ignition ON (engine off).
  • Access the [FUEL_PRES] PID and simulation item [FUEL_PUMP_REQ] using the M-MDS. (See PID/DATA MONITOR INSPECTION .) (See SIMULATION INSPECTION .)
  • Turn the simulation item [FUEL_PUMP_REQ] on.
  • Is the [FUEL_PRES] PID value 425-505 kPa {4.34-5.14 kgf/cm2 , 61.7-73.2 psi}?
Yes Go to the next step.
No Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 5.
8 PURPOSE: VERIFY IF MALFUNCTION CAUSED BY FUEL INJECTOR OPERATION MALFUNCTION 
  • Switch the ignition off.
  • Reconnect all disconnected connectors.
  • Start the engine and idle it.
  • Access the following simulation items using the M-MDS: (See SIMULATION INSPECTION .)
    • INJ
  • Stops the operation of each of the fuel injectors using the simulation function.
  • Does the vibration during idling worsen?
Yes Go to the next step.
No Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 6.
9 PURPOSE: VERIFY IF MALFUNCTION CAUSED BY PURGE SOLENOID VALVE OPERATION MALFUNCTION 
  • Start the engine and idle it.
  • Access the PCM PID [PRG_DUTY] using the M-MDS.

    (See PID/DATA MONITOR INSPECTION .)

  • Is the [PRG_DUTY] PID value normal?
Yes Go to the next step.
No Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 7.
10 PURPOSE: VERIFY IF MALFUNCTION CAUSED BY MAF SENSOR MALFUNCTION 
  • Start the engine and idle it.
  • Access the PCM PID [MAF] using the M-MDS.

    (See PID/DATA MONITOR INSPECTION .)

  • Is the [MAF] PID value normal?
Yes Go to the next step.
No Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 9.
11 PURPOSE: VERIFY IF MALFUNCTION CAUSED BY MAP SENSOR MALFUNCTION 
  • Start the engine and idle it.
  • Access the following PIDs using the M-MDS: (See PID/DATA MONITOR INSPECTION .)
    • MAP
    • MAP_VOLT
  • Are all items normal?
Yes Go to the next step.
No Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 11.
12 PURPOSE: VERIFY IF MALFUNCTION CAUSED BY INTAKE VALVE TIMING MALFUNCTION 
  • Start the engine and idle it.
  • Access the following PIDs using the M-MDS: (See PID/DATA MONITOR INSPECTION .)
    • VLV_TIMING_ACT_IN
    • VLV_TIMING_DSD_IN
  • Depress the accelerator pedal to increase the engine speed.
  • Does the monitor value of the PID item [VLV_TIMING_ACT_IN] conform to the [VLV_TIMING_DSD_IN] PID value?
Yes Go to the next step.
No Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 13.
13 PURPOSE: VERIFY IF MALFUNCTION CAUSED BY EXHAUST VALVE TIMING MALFUNCTION 
  • Start the engine and idle it.
  • Access the following PIDs using the M-MDS: (See PID/DATA MONITOR INSPECTION .)
    • VLV_TIMING_ACT_EX
    • VLV_TIMING_DSD_EX
  • Perform the following:
    1. Warm up the engine to allow the engine coolant temperature to reach 80°C {176°F} or more.
    2. Shift to 2nd gear (MT)/D position (AT) and rapidly accelerate the vehicle to 50 km/h {31 mph} (to operate hydraulic variable valve timing control).
    3. Decelerate to idling.
    4. Shift to 2nd gear (MT)/D position (AT) and rapidly accelerate the vehicle to 50 km/h {31 mph} again.
  • Does the monitor value of the PID item [VLV_TIMING_ACT_EX] conform to the [VLV_TIMING_DSD_EX] PID value?
Yes Go to the next step.
No Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 16.
14 PURPOSE: VERIFY IF MALFUNCTION CAUSED BY A/F SENSOR MALFUNCTION 
Yes Go to the next step.
No Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 17.
15 PURPOSE: INSPECT FOR OTHER RELATED DTC 
  • Perform the DTC inspection for the PCM. (See DTC INSPECTION .)
  • Are any other DTCs displayed?
Yes Repair or replace the malfunctioning location according to the applicable DTC troubleshooting.
(See DTC TABLE [PCM (SKYACTIV-G)] .)
Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 1.
No Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 1.