LEMON Manuals: Even more car manuals for everyone

DTC P2271

DETECTION CONDITION AND POSSIBLE CAUSE (DTC P2271 - LF, L3)

DTC P2271 Middle HO2S signal stuck rich
DETECTION CONDITION 
  • The PCM monitors the middle HO2S input voltage when the following conditions are met. If the subtracted input voltage from the target voltage (calculated by PCM) is 0.85 V or more  for 25 s,  or is above 0.3 V  when the fuel cut, the PCM determines that the front HO2S signal remains rich.

    MONITORING CONDITION 

    • ECT: more than 70 °C {158 °F} 
    • Engine speed: more than 1, 500 RPM 
    • MAF amount: more than 10 g/s {1.32 lb/min} 
    • Short term fuel trim: -20-20%
    • Long term fuel trim: -15-15%
    • Fuel injection system status: feedback control
  • Diagnostic support note 

  • This is a intermittent monitor (HO2S).
  • The MIL illuminates if PCM detects the above malfunctioning condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.
  • PENDING CODE is available if PCM detects the above malfunction conditions during first drive cycle.
  • FREEZE FRAME DATA is available.
  • DTC is stored in the PCM memory.
POSSIBLE CAUSE 
  • Leakage exhaust gas
  • Middle HO2S malfunction
  • Front HO2S malfunction
  • Rear HO2S malfunction
  • Front HO2S heater malfunction
  • Middle HO2S heater malfunction
  • Rear HO2S heater malfunction
  • Fuel pump control malfunction
  • Fuel pressure malfunction
  • Fuel injector malfunction
  • Leakage exhaust gas
  • Leakage engine coolant
  • Purge solenoid valve malfunction
  • Purge solenoid valve hoses improper connection
  • Restriction in intake-air system
  • Insufficient compression
    • Engine oil malfunction
    • Increase oil pressure
    • Metering oil pump malfunction
    • Metering oil pump control malfunction
    • Engine malfunction
  • PCM malfunction
DIAGNOSTIC PROCEDURE CHART

STEP INSPECTION ACTION
1 VERIFY FREEZE FRAME DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAVE BEEN RECORDED 
  • Have FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS (HO2S related) been recorded?
Yes Go to the next step.
No Record the FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS on the repair order, then go to the next step.
2 VERIFY REPAIR INFORMATION AVAILABILITY 
  • Verify related service Bulletins and/or on-line repair information availability.
  • Is any related repair information available?
Yes Perform repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the applicable DTC inspection.
(See DTC TABLE ).
3 VERIFY RELATED PENDING CODE OR STORED DTC 
  • Turn the ignition switch off, then to the ON position (Engine off).
  • Verify the related PENDING CODE or stored DTCs.
  • Is DTC P2196 present?
Yes Go to the applicable DTC inspection.
(See DTC TABLE ).
No Go to the next step.
4 IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA 
  • Is DTC P2270 on FREEZE FRAME DATA?
Yes Go to the next step.
No Go to FREEZE FRAME DATA DTC inspection.
(See DTC TABLE ).
5 VERIFY CURRENT INPUT SIGNAL STATUS OF MIDDLE HO2S 
  • Start the engine and warm it up completely.
  • Access O2S12 PID using WDS or equivalent.
  • Check PID under following accelerator pedal condition (in PARK (ATX) or NEUTRAL (MTX).
  • Is PID reading normal?
    • More than 0.45 V  when accelerator pedal is suddenly depressed (rich condition).
    • Less than 0.45 V  just after release of accelerator pedal (lean condition)
Yes Go to the next step.
No Visually inspect for any gas leakage between the exhaust manifold and the middle HO2S.
Then go to the next step.
6 VERIFY TROUBLESHOOTING OF DTC P2271 COMPLETED 
  • Make sure to reconnect all disconnected connectors.
  • Clear the DTC from the PCM memory using the WDS or equivalent.
  • Stop the vehicle and access ON BOARD READINESS TEST to inspect drive mode completion status.
  • Verify O2S_EVAL PID changes to yes.
    • If not, perform the DRIVE MODE again.
  • Is the PENDING CODE for this DTC present?
Yes Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION ).
No Go to the next step.
7 VERIFY AFTER REPAIR PROCEDURE  Yes Go to the applicable DTC inspection.
(See DTC TABLE ).
No Troubleshooting completed.