LEMON Manuals: Even more car manuals for everyone

DTC P2270

DETECTION CONDITION AND POSSIBLE CAUSE (DTC P2270 - LF, L3)

DTC P2270 Middle HO2S signal stuck lean
DETECTION CONDITION 
  • The PCM monitors the middle HO2S input voltage when the following conditions are met. If the subtracted input voltage from the target voltage (calculated by PCM) is 0.4 V or less  for 30 s  , the PCM determines that the front HO2S signal remains lean.

    MONITORING CONDITION 

    • ECT: more than 70°C {158°F} 
    • Engine speed: more than 1, 500 RPM 
    • MAF amount: more than 10 g/s {1.32 lb/min} 
    • Short term fuel trim: -20-20% 
    • Long term fuel trim: -15-15% 
    • Fuel injection system status: feedback control
  • Diagnostic support note 

  • This is a intermittent monitor (HO2S).
  • The MIL illuminates if PCM detects the above malfunctioning condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.
  • PENDING CODE is available if PCM detects the above malfunction conditions during first drive cycle.
  • FREEZE FRAME DATA is available.
  • DTC is stored in the PCM memory.
POSSIBLE CAUSE 
  • Leakage exhaust gas
  • Middle HO2S malfunction
  • Leakage fuel
  • Fuel injector malfunction
  • Air suction at intake-air system
  • MAF sensor malfunction
  • ECT sensor malfunction
  • PCM malfunction
DIAGNOSTIC PROCEDURE CHART

STEP INSPECTION ACTION
1 VERIFY FREEZE FRAME DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAVE BEEN RECORDED 
  • Have FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS (HO2S related) been recorded?
Yes Go to the next step.
No Record the FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS on the repair order, then go to the next step.
2 VERIFY REPAIR INFORMATION AVAILABILITY 
  • Verify related service Bulletins and/or on-line repair information availability.
  • Is any related repair information available?
Yes Perform repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
3 VERIFY RELATED PENDING CODE OR STORED DTC 
  • Turn the ignition switch off, then ON position (Engine off).
  • Verify the related PENDING CODE or stored DTCs.
  • Is the DTC P2195 present?
Yes Go to the applicable DTC inspection.
(See DTC TABLE ).
No Go to the next step.
4 IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA 
  • Is DTC P2270 on FREEZE FRAME DATA?
Yes Go to the next step.
No Go to FREEZE FRAME DATA DTC inspection.
(See DTC TABLE ).
5 VERIFY CURRENT INPUT SIGNAL STATUS OF THE MIDDLE HO2S 
  • Start the engine and warm it up completely.
  • Access O2S12 PID using WDS or equivalent.
  • Check PID under following accelerator pedal condition (in PARK (ATX) or NEUTRAL (MTX).
  • Is PID reading okay?
    • More than 0.45V when accelerator pedal is suddenly depressed (rich condition). 
    • Less than 0.45V  just after release of accelerator pedal (lean condition)
Yes Go to the next step.
No Visually inspect for any gas leakage between the exhaust manifold and the middle HO2S.
Then go to the next step.
6 VERIFY TROUBLESHOOTING OF DTC P2270 COMPLETED 
  • Make sure to reconnect all disconnected connectors.
  • Clear the DTC from the PCM memory using the WDS or equivalent.
  • Stop the vehicle and access ON BOARD READINESS TEST to inspect drive mode completion status.
  • Verify O2S_EVAL PID changes to yes.
    • If not, perform the DRIVE MODE again.
  • Is the PENDING CODE for this DTC present?
Yes Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION ).
No Go to the next step.
7 VERIFY AFTER REPAIR PROCEDURE  Yes Go to the applicable DTC inspection.
(See DTC TABLE ).
No Troubleshooting completed.