LEMON Manuals: Even more car manuals for everyone

DTC P2237

DETECTION CONDITION AND POSSIBLE CAUSE (DTC P2237 - LF, L3)

DTC P2237 Front HO2S positive current control circuit open
DETECTION CONDITION 
  • The PCM monitors front HO2S positive current control circuit voltage. If the voltage is not changed against the PCM control value while the engine running, the PCM determines that the front HO2S positive current control circuit is open.
  • Diagnostic support note 

  • This is a continuous monitor (HO2S).
  • The MIL illuminates if PCM detects the above malfunctioning condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.
  • PENDING CODE is available if PCM detects the above malfunction conditions during first drive cycle.
  • FREEZE FRAME DATA is available.
  • DTC is stored in the PCM memory.
POSSIBLE CAUSE 
  • Front HO2S malfunction
  • Connector or terminal malfunction
  • Open circuit between PCM terminal 2AD and front HO2S terminal B
  • PCM malfunction
G04313430Courtesy of MAZDA MOTORS CORP.
DIAGNOSTIC PROCEDURE CHART

STEP INSPECTION ACTION
1 VERIFY FREEZE FRAME DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAVE BEEN RECORDED 
  • Have FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS (HO2S related) been recorded?
Yes Go to the next step.
No Record the FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS on the repair order, then go to the next step.
2 VERIFY RELATED REPAIR INFORMATION AVAILABILITY 
  • Verify related Service Bulletins and/or on-line repair information availability.
  • Is any related repair information available?
Yes Perform repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
3 IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA 
  • Is DTC P2237 on FREEZE FRAME DATA?
Yes Go to the next step.
No Go to troubleshooting for DTC on FREEZE FRAME DATA.
(See DTC TABLE ).
4 INSPECT FRONT HO2S CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch to off.
  • Disconnect the front HO2S connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, and corrosion)
  • Is there any malfunction?
Yes Repair or replace the terminal, then go to Step 7.
No Go to the next step.
5 INSPECT PCM CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch to off.
  • Disconnect the PCM connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, and corrosion).
  • Is there any malfunction?
Yes Repair or replace the terminal, then go to Step 7.
No Go to the next step.
6 INSPECT FRONT HO2S POSITIVE CURRENT CIRCUIT FOR OPEN CIRCUIT 
  • Front HO2S and PCM connectors disconnected.
  • Verify the continuity between PCM terminal 2AD (wiring harness-side) and front HO2S terminal B (wiring harness-side).
  • Is there continuity?
Yes Replace the front HO2S, then go to the next step.
No Repair or replace wiring harness for open, then go to the next step.
7 VERIFY TROUBLESHOOTING OF DTC P2237 COMPLETED 
  • Make sure to reconnect all disconnected
  • Clear the DTC from the PCM memory using the WDS or equivalent.
  • Perform the KOEO or KOER self-test.

    (See KOEO/KOER SELF TEST ] ).

  • Is the DTC P2237 present?
Yes Replace PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION ).
No Go to the next step.
8 VERIFY AFTER REPAIR PROCEDURE  Yes Go to the applicable DTC inspection.
(See DTC TABLE ).
No Troubleshooting completed.