LEMON Manuals: Even more car manuals for everyone

DTC P2102

DETECTION CONDITION AND POSSIBLE CAUSE (DTC P2102 - LF, L3)

DTC P2102 Throttle actuator circuit low input
DETECTION CONDITION 
  • The PCM monitors the throttle actuator circuit current. If the PCM detects that throttle actuator circuit current is excessive low, the PCM determines that the throttle actuator circuit has a malfunction.
  • Diagnostic support note 

  • This is a continuous monitor (CCM).
  • The MIL illuminates if the PCM detects the above malfunction condition during the first drive cycle.
  • The PENDING CODE is available if the PCM detects the above malfunction condition.
  • FREEZE FRAME DATA is available.
  • The DTC is stored in the PCM memory.
POSSIBLE CAUSE 
  • Short to ground circuit between the throttle body terminal F and the PCM terminal 2A
  • Short to ground circuit between the throttle body terminal E and the PCM terminal 2B
  • Poor connection of the throttle body or the PCM connector
  • Throttle valve motor malfunction
  • PCM malfunction
G04313424Courtesy of MAZDA MOTORS CORP.
DIAGNOSTIC PROCEDURE CHART

STEP INSPECTION ACTION
1 VERIFY FREEZE FRAME DATA HAS BEEN RECORDED 
  • Has FREEZE FRAME DATA been recorded?
Yes Go to the next step.
No Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2 VERIFY RELATED REPAIR INFORMATION AVAILABILITY 
  • Verify related Service Bulletins and/or on-line repair information availability.
  • Is any related repair information available?
Yes Perform repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
3 VERIFY RELATED PENDING CODE AND STORED DTCS 
  • Turn the ignition switch off, then to the ON position (Engine off).
  • Verify the pending or stored DTCs using the WDS or equivalent.
  • Is DTC P2100 also present?
Yes Go to the appropriate DTC inspection, then go to Step 9. (See DTC TABLE ).
No Go to the next step.
4 INSPECT THROTTLE BODY CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch off.
  • Disconnect the throttle body connector.
  • Inspect for poor connection (such as damaged, pulled-put pins, corrosion).
  • Is there any malfunction?
Yes Repair or replace the terminal, then go to Step 9.
No Go to the next step.
5 INSPECT POWER SUPPLY CIRCUIT OF THROTTLE ACTUATOR FOR SHORT TO GROUND 
  • Turn the ignition switch off.
  • Inspect for continuity between throttle body terminal F (wiring harness-side) and body ground.
  • Is there continuity?
Yes Repair or replace the wiring harness for short to ground, then go to Step 9.
No Go to the next step.
6 INSPECT PCM CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch off.
  • Disconnect the PCM connector.
  • Inspect for poor connection (such as damaged, pulled-out pins, corrosion).
  • Is there any malfunction?
Yes Repair or replace the terminal, then go to Step 9.
No Go to the next step.
7 INSPECT CONTROL CIRCUIT OF THROTTLE ACTUATOR FOR SHORT TO GROUND 
  • Turn the ignition switch off.
  • Inspect for continuity between throttle body terminal E (wiring harness-side) and body ground.
  • Is there continuity?
Yes Repair or replace the wiring harness for short to ground, then go to Step 9.
No Go to the next step.
8 INSPECT THROTTLE ACTUATOR  Yes Go to the next step.
No Replace the throttle body, then go to the next step.
9 VERIFY TROUBLESHOOTING OF DTC P2102 COMPLETED 
  • Make sure to reconnect all disconnected connectors.
  • Turn the ignition switch to the ON position (Engine off).
  • Clear the DTC from the PCM memory using the WDS or equivalent.
  • Start the engine and warm it up completely.
  • Is the same DTC present?
Yes Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION ).
No Go to the next step.
10 VERIFY AFTER REPAIR PROCEDURE  Yes Go to the applicable DTC inspection. (See DTC TABLE ).
No Troubleshooting completed.