LEMON Manuals: Even more car manuals for everyone

DTC P0571

DETECTION CONDITION AND POSSIBLE CAUSE (DTC P0571 - LF, L3)

DTC P0571 Brake switch circuit problem
DETECTION CONDITION 
  • The PCM monitors changes in input voltage for brake switch No. 1 and No. 2 (signal from instrument cluster). If the PCM detects that both brake switches No. 1 and No. 2 remain on or off for 15 s  , it determines that the brake switch circuit has a malfunction.
  • Diagnostic support note 

  • This is a continuous monitor (Other).
  • MIL does not comes on.
  • PENDING CODE is available if PCM detects the above malfunction condition.
  • FREEZE FRAME DATA is not available.
  • DTC is stored in PCM memory.
POSSIBLE CAUSE 
  • Brake switch malfunction
  • Open circuit between brake switch terminal B and instrument cluster terminal 2M
  • Open circuit between brake switch terminal C and body ground
  • Short to power between brake switch terminal B and instrument cluster terminal 2M
  • Short to ground circuit between brake switch terminal B and instrument cluster terminal 2M
  • Communication error between PCM and instrument cluster
  • PCM malfunction
G04313410Courtesy of MAZDA MOTORS CORP.
DIAGNOSTIC PROCEDURE CHART

STEP INSPECTION ACTION
1 VERIFY FREEZE FRAME DATA HAS BEEN RECORDED 
  • Has FREEZE FRAME DATA been recorded?
Yes Go to the next step.
No Record FREEZE FRAME DATA on repair, then go to the next step.
2 VERIFY RELATED REPAIR INFORMATION AVAILABILITY 
  • Check for related Service Bulletins and/or on-line repair information availability.
  • Is any related repair information available?
Yes Perform repair or diagnosis according to available repair information.
  • If vehicle is not repaired, go to the next step.
No Go to the next step.
3 VERIFY DTC FOR MODULE COMMUNICATION 
  • Connect WDS or equivalent to DLC-2.
  • Turn the ignition switch to the ON position (Engine off).
  • Verify stored DTC.
  • Is DTC U0155 stored?
Yes Go to the applicable DTC inspection.
(See DTC TABLE ).
No Go to the next step.
4 VERIFY RELATED PENDING CODE OR STORED DTC 
  • Turn the ignition switch off then to the ON position (Engine off).
  • Verify the related PENDING CODE or stored DTCs.
  • Is the DTC P0703 also present?
Yes Go to the applicable DTC inspection.
(See DTC TABLE ).
No Go to the next step.
5 INSPECT BRAKE SWITCH CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch off.
  • Disconnect the brake switch connector.
  • Inspect for poor connection (such as damaged, pull-out pins, corrosion).
  • Is there any malfunction?
Yes Repair or replace the terminal, then go to Step 11.
No Go to the next step.
6 INSPECT BRAKE SWITCH 
  • Inspect the brake switch.
  • Is the brake switch normal?
Yes Go to the next step.
No Replace brake switch, then go to Step 11.
7 INSPECT GROUND CIRCUIT OF BRAKE SWITCH NO. 2 FOR OPEN CIRCUIT 
  • Inspect for continuity between brake switch terminal C (wiring harness-side) and body ground.
  • Is there continuity?
Yes Go to the next step.
No Repair or replace the wiring harness for open circuit, then go to Step 11.
8 INSPECT SIGNAL CIRCUIT OF BRAKE SWITCH NO. 2 FOR SHORT TO GROUND 
  • Inspect for continuity between brake switch terminal B (wiring harness-side) and body ground.
  • Is there continuity?
Yes Repair or replace the wiring harness for short to ground circuit, then go to Step 11.
No Go to the next step.
9 INSPECT INSTRUMENT CLUSTER CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch off.
  • Disconnect instrument cluster connector.
  • Inspect for poor connection (such as damaged, pull-out pins, corrosion).
  • Is there any malfunction?
Yes Repair or replace the terminal, then go to Step 11.
No Go to the next step.
10 INSPECT SIGNAL CIRCUIT OF BRAKE SWITCH NO. 2 FOR OPEN CIRCUIT 
  • Inspect for continuity between brake switch terminal B (wiring harness-side) and instrument cluster terminal 2M (wiring harness-side).
  • Is there continuity?
Yes Go to the next step.
No Repair or replace the wiring harness for open circuit, then go to Step 11.
11 INSPECT SIGNAL CIRCUIT OF BRAKE SWITCH NO. 2 FOR SHORT TO POWER 
  • Turn the ignition switch to the ON position (Engine off).
  • Measure the voltage between brake switch terminal B (wiring harness-side) and body ground.
  • Is the voltage B+  ?
Yes Repair or replace the wiring harness for short to power circuit, then go to the next step.
No Go to the next step.
12 VERIFY TROUBLESHOOTING OF P0571 COMPLETED 
  • Make sure to reconnect all disconnected connectors.
  • Clear the DTC from the PCM memory using the WDS or equivalent.
  • Turn the ignition switch to the ON position (Engine off).
  • Depress and release the brake pedal more than 5 times  .
  • Is the same DTC present?
Yes Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION ).
No Go to the next step.
13 VERIFY AFTER REPAIR PROCEDURE  Yes Go to the applicable DTC inspection.
(See DTC TABLE ).
No Troubleshooting completed.