LEMON Manuals: Even more car manuals for everyone

DTC P0340

DETECTION CONDITION AND POSSIBLE CAUSE (DTC P0340 - LF, L3)

DTC P0340 CMP sensor circuit problem
DETECTION CONDITION 
  • The PCM monitors the input voltage from the CMP sensor when the engine is running. If the PCM does not receive the input voltage from the CMP sensor while the PCM receives the input signal from the CKP sensor, the PCM determines that the CMP circuit has a malfunction.
  • Diagnostic support note 

  • This is a continuous monitor (CCM).
  • MIL illuminates if the PCM detects the above malfunction condition during first drive cycle.
  • PENDING CODE is available if the PCM detects the above malfunction condition.
  • FREEZE FRAME DATA is available.
  • DTCs are stored in the PCM memory.
POSSIBLE CAUSE 
  • CMP sensor malfunction
  • Connector or terminal malfunction
  • CMP sensor is dirty
  • Short to the power circuit between CMP sensor terminal B and PCM terminal 2S(1), 2V(2)
  • Short to ground circuit between CMP sensor terminal C and PCM terminal 2AM(1), 2X(2)
  • Short to ground circuit between CMP sensor terminal B and PCM terminal 2S(1), 2V(2)
  • Open circuit between CMP sensor terminal A and body ground
  • Open circuit between CMP sensor terminal B and PCM terminal 2S(1), 2V(2)
  • Open circuit between CMP sensor terminal C and PCM terminal 2AM(1), 2X(2)
  • Both CMP sensor wires are shorted to each other
  • CKP sensor pulse wheel malfunction
  • CKP sensor mis-installation
  • Timing chain mis-installation
  • Loose timing chain or improper valve timing
  • Loose camshaft sprocket lock bolt
  • Loose crankshaft pulley lock bolt
  • PCM malfunction
G04313404Courtesy of MAZDA MOTORS CORP.
(1) LF MTX, L3 and California emission regulation applicable model with LF ATX
(2) Except for California emission regulation applicable model with LF ATX
DIAGNOSTIC PROCEDURE CHART

STEP INSPECTION ACTION
1 VERIFY FREEZE FRAME DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAS BEEN RECORDED 
  • Has FREEZE FRAME DATA been recorded?
Yes Go to the next step.
No Record the FREEZE FRAME on the repair order, then go to the next step.
2 VERIFY RELATED REPAIR INFORMATION AVAILABILITY 
  • Check for related Service Bulletins and/or online repair information availability.
  • Is any related repair information available?
Yes Perform repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
3 VERIFY CMP SENSOR VOLTAGE 
  • Disconnect the CMP sensor connector.
  • Connect a voltmeter between CMP sensor connector terminals B and C (sensor-side).
  • Inspect the voltage in AC range while cranking the engine.
  • Is there any voltage?
Yes Go to the next step.
No Go to step 10.
4 INSPECT CMP SENSOR CONNECTOR FOR POOR CONNECTION 
  • Verify that the CMP sensor connector is connected securely.
  • Is the connector normal?
Yes Go to the next step.
No Reconnect the connector, then go to Step 15.
5 INSPECT CMP CIRCUIT FOR SHORT TO POWER 
  • Turn the ignition switch off.
  • Disconnect the CMP sensor connector.
  • Turn ignition switch to the ON position (Engine off)
  • Measure voltage between the CMP sensor connector terminal B (wiring harness-side) and body ground.
  • Is the voltage B+  ?
Yes Repair or replace the suspected wiring harness, then go to Step 15.
No Go to the next step.
6 INSPECT CMP CIRCUIT FOR SHORT TO GROUND 
  • Inspect for continuity between the following terminal and body ground:
    • CMP sensor connector terminal B (wiring harness-side)
    • CMP sensor connector terminal C (wiring harness-side)
  • Is there continuity?
Yes Repair or replace the suspected wiring harness, then go to Step 15.
No Go to the next step.
7 INSPECT CMP CIRCUITS FOR SHORT CIRCUIT 
  • Inspect for continuity between CMP sensor connector terminals B and C (wiring harness-side).
  • Is there continuity?
Yes Repair or replace the suspected wiring harness, then go to Step 15.
No Go to the next step.
8 INSPECT PCM CONNECTOR FOR POOR CONNECTION 
  • Disconnect the PCM connector.
  • Inspect for poor connection (damaged, pulled-out terminals, corrosion, etc).
  • Is there any malfunction?
Yes Repair the terminal, then go to Step 15.
No Go to the next step.
9 INSPECT CMP CIRCUIT FOR OPEN CIRCUIT 
  • Inspect for continuity between the following circuits:
    • CMP sensor terminal A (wiring harness-side) and body ground
    • CMP sensor terminal B (wiring harness-side) and PCM terminal 2S(1), 2V(2) (wiring harness-side)
    • CMP sensor terminal C (wiring harness-side) and PCM terminal 2AM(1), 2X(2) (wiring harness-side)
  • Is there continuity?
Yes Go to Step 11.
No Repair or replace the suspected wiring harness, then go to Step 15.
10 INSPECT CMP SENSOR  Yes Go to the Step 15.
No Replace the CMP sensor and go to Step 15.
11 VERIFY CKP SENSOR INSTALLATION  Yes Go to the next step.
No Reinstall the CKP sensor and go to Step 15.
12 VERIFY VALVE TIMING MECHANISM INSTALLATION 
  • Verify the valve timing mechanism installation for the following parts:
    • Timing chain mis-installation
    • Loose camshaft sprocket lock bolt
    • Loose crankshaft pulley lock bolt
  • Is the valve timing mechanism installed correctly?
Yes Go to the next step.
No Reinstall the following parts and go to Step 15.
  • Timing chain
  • Camshaft sprocket
  • Crankshaft pulley
13 INSPECT STOPPER PIN MECHANISM (LF, L3)  Yes Go to the next step.
No Replace the variable valve timing actuator, then go to Step 15.
14 INSPECT ROTOR POSITION (LF, L3)  Yes VARIABLE VALVE TIMING MECHANISM NORMAL 
NOTE:
  • This DTC is detected as an intermittent concern.
  • The intermittent concern might be removed by cleaning the variable valve timing mode control function.

Go to the next step.
No Replace the variable valve timing actuator, then go to the next step.
15 VERIFY TROUBLESHOOTING OF DTC P0340 COMPLETED 
  • Make sure to reconnect all disconnected connectors.
  • Turn ignition switch to the ON position (Engine off).
  • Clear the DTC from the PCM memory using the WDS or equivalent.
  • Start the engine.
  • Access the MAF PID using the WDS or equivalent.
    NOTE:
    • The MAF PID should indicate 1.95 g/s {0.25 lb/min.} or above  during this test
  • Is same DTC present?
Yes Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION ).
No Go to the next step.
16 VERIFY AFTER REPAIR PROCEDURE  Yes Go to the applicable DTC inspection.
(See DTC TABLE ).
No Troubleshooting completed.
(1) LF MTX, L3 and California emission regulation applicable model with LF ATX
(2) Except for California emission regulation applicable model with LF ATX