LEMON Manuals: Even more car manuals for everyone

DTC P0138

DETECTION CONDITION AND POSSIBLE CAUSE (DTC P0138 - LF, L3)

DTC P0138 Middle(1)/Rear(2)(3) HO2S circuit high input
DETECTION CONDITION 
  • The PCM monitors input voltage from middle(1)/rear(2)(3) HO2S. If the input voltage from the middle(1)/rear(2)(3) HO2S sensor is above 1.2 V  for 0.5 s (1) /0.8 s (2) (3)  , the PCM determines that circuit input is high.
  • Diagnostic support note 

  • This is a continues monitor (HO2S).
  • The MIL illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.
  • PENDING CODE is available if the PCM detects the above malfunction condition during first drive cycle.
  • FREEZE FRAME DATA is available.
  • DTC is stored in the PCM memory.
POSSIBLE CAUSE 
  • Middle(1)/Rear(2)(3) HO2S malfunction
  • Short to power supply in wiring harness between middle(1)/rear(2)(3) HO2S terminal A and PCM terminal 2R(1), 2AH(2), 2Q(3)
  • Middle(1)/Rear(2)(3) HO2S or PCM terminal shorted
  • PCM malfunction
G04313396Courtesy of MAZDA MOTORS CORP.
(1) California emission regulation applicable model
(2) Except for California emission regulation applicable model with LF ATX
(3) Except for California emission regulation applicable model with LF MTX, L3
DIAGNOSTIC PROCEDURE CHART

STEP INSPECTION ACTION
1 VERIFY FREEZE FRAME DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAVE BEEN RECORDED 
  • Have FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS (HO2S related) been recorded?
Yes Go to the next step.
No Record the FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS on repair order, then go to the next step.
2 VERIFY RELATED SERVICE INFORMATION AVAILABILITY 
  • Verify related service bulletins and/or repair Information availability.
  • Is any related Service Information available?
Yes Perform repair or diagnosis according to available Service Information.
  • If vehicle is not repaired, go to the next step.
No Go to the next step.
3 VERIFY RELATED PENDING OR STORED DTC 
  • Turn the ignition switch off, then to the ON position. (Engine off)
  • Verify pending code or stored DTCs using WDS or equivalent.
  • Is other DTC present?
Yes Go to the appropriate DTC troubleshooting procedures.
(See DTC TABLE ).
No Go to the next step.
4 IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA 
  • Is DTC P0138 on FREEZE FRAME DATA?
Yes Go to the next step.
No Go to troubleshooting procedures for DTC on FREEZE FRAME DATA.
(See DTC TABLE ).
5 INSPECT MIDDLE (1) /REAR (2) (3)  HO2S SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY 
  • Turn the ignition switch off.
  • Disconnect middle(1)/rear(2)(3) HO2S connector.
  • Turn the ignition switch to the ON position. (Engine off)
  • Measure the voltage between middle(1)/rear(2)(3) HO2S terminal A (wiring harness-side) and body ground.
  • Is there any voltage?
Yes Replace short to power supply, then go to Step 7.
No Go to the next step.
6 VERIFY CURRENT INPUT SIGNAL STATUS 
  • Start engine.
  • Access O2S12 PID using WDS or equivalent.
  • Verify PID while racing engine at least 10 times  in PARK (ATX) or NEUTRAL (MTX).
  • Does PID stay above 0.55 V  ?
Yes Replace sensor, then go to the next step.
(See HEATED OXYGEN SENSOR (HO2S) REMOVAL/INSTALLATION ).
No Go to the next step.
7 VERIFY TROUBLESHOOTING OF DTC P0138 COMPLETED 
  • Make sure to reconnect all disconnected connectors.
  • Turn the ignition switch to the ON position. (Engine off)
  • Clear the DTC from the memory using the WDS or equivalent.
  • Run the KOEO or KOER self-test with WDS or equivalent, or PCM adaptive memory procedure drive mode and HO2S heater, HO2S, and TWC repair verification drive mode.

    (See OBD-II DRIVE MODE ).

  • Is the PENDING CODE for this DTC present?
Yes Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION ).
No Go to the next step.
8 VERIFY AFTER REPAIR PROCEDURE  Yes Go to the applicable DTC troubleshooting.
(See DTC TABLE ).
No Troubleshooting completed.
(1) California emission regulation applicable model
(2) Except for California emission regulation applicable model with LF ATX
(3) Except for California emission regulation applicable model with LF MTX, L3