LEMON Manuals: Even more car manuals for everyone

Instrument Panel Upper Section: Removal

NOTE: Removal steps in this procedure may contain installation details.
  1. Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering .
  2. Release the clips and remove the switch assembly.

    • Disconnect the electrical connector.

      Use the General Equipment: Interior Trim Remover

    GFD534919Courtesy of FORD MOTOR COMPANY
  3. Release the clips and remove the finish panel.

    Use the General Equipment: Interior Trim Remover

    GFD534918Courtesy of FORD MOTOR COMPANY
  4. Release the clips and remove the RH instrument panel end cap.

    Use the General Equipment: Interior Trim Remover

    GFD534928Courtesy of FORD MOTOR COMPANY
  5. Fully lower the glove compartment.

    1. Disconnect the check strap.
    2. Push the stop tabs inward.

    GFD534921Courtesy of FORD MOTOR COMPANY
  6. Release the clips and remove the RH instrument panel trim panel.

    Use the General Equipment: Interior Trim Remover

    GFD534922Courtesy of FORD MOTOR COMPANY
    • Remove the bolt.

      Torque: 28 lb.in (3.2 Nm)

    • Release the clips and remove the center instrument panel trim panel.

    • Disconnect the electrical connector.

    GFD534920Courtesy of FORD MOTOR COMPANY
  7. Remove the glove compartment assembly.

    • Remove the upper bolts.

      Torque: 28 lb.in (3.2 Nm)

    • Remove the lower bolts, release the clips and remove the glove compartment assembly.

      Torque: 22 lb.in (2.5 Nm)

    • Disconnect the electrical connector.

    GFD534923Courtesy of FORD MOTOR COMPANY
  8. Detach the push pin, disconnect the electrical connector and position the harness aside.
    GFD534948Courtesy of FORD MOTOR COMPANY
  9. Release the clips and remove the instrument panel speaker grille.

    Use the General Equipment: Interior Trim Remover 

    GFD534949Courtesy of FORD MOTOR COMPANY
  10. Remove the bolts and the instrument panel speaker.

    • Disconnect the electrical connector.

      Torque: 22 lb.in (2.5 Nm)

    GFD534950Courtesy of FORD MOTOR COMPANY
  11. Release the clips and remove the cover.
    GFD534951Courtesy of FORD MOTOR COMPANY
  12. Remove the bolts and the FDIM.

    • Disconnect the electrical connector.

      Torque: 71 lb.in (8 Nm)

    GFD534952Courtesy of FORD MOTOR COMPANY
  13. Remove the bolts, release the clips and remove the center instrument panel finish panel.

    • Disconnect the electrical connector.

      Torque: 22 lb.in (2.5 Nm)

    GFD534953Courtesy of FORD MOTOR COMPANY
  14. Release the clips and remove the LH instrument panel end cap.

    Use the General Equipment: Interior Trim Remover

    GFD534931Courtesy of FORD MOTOR COMPANY
  15. Release the clips and remove the LH instrument panel center trim panel.

    Use the General Equipment: Interior Trim Remover

    GFD534954Courtesy of FORD MOTOR COMPANY
  16. Position downward the lower steering column trim panel.
    GFD534936Courtesy of FORD MOTOR COMPANY
  17. Remove the bolts, release the clips and remove the IPC trim panel.

    • Disconnect the electrical connector.

    GFD534955Courtesy of FORD MOTOR COMPANY
  18. Remove the A-pillar trim panels Refer to: A-Pillar Trim Panel .
  19. NOTE: During installation, make sure to apply pressure to the trim panel at the same angle as the retaining clips. To fully seat the trim panel, start at the center of the trim panel and then seat the panel working from the center right side outward and then the center left side outward.

    Release the clips and remove the defroster grille panel.

    • Disconnect the electrical connector.

      Use the General Equipment: Interior Trim Remover

    GFD534956Courtesy of FORD MOTOR COMPANY
  20. Remove the passenger side air bag support bracket bolt.

    Torque: 28 lb.in (3.2 Nm)

    GFD534957Courtesy of FORD MOTOR COMPANY
  21. Remove the passenger side air bag to in-vehicle cross beam bolts.

    Torque: 93 lb.in (10.5 Nm)

    GFD534958Courtesy of FORD MOTOR COMPANY
  22. Remove the bolts.

    Torque: 22 lb.in (2.5 Nm)

    GFD534959Courtesy of FORD MOTOR COMPANY
  23. Remove the bolts and position the instrument panel upper section upwards.

    Torque: 22 lb.in (2.5 Nm)

    GFD534960Courtesy of FORD MOTOR COMPANY
  24. Remove the instrument panel upper section.
GFD534961Courtesy of FORD MOTOR COMPANY