LEMON Manuals: Even more car manuals for everyone

Section 20 (Engine - 3.0L ECOBOOST): Installation: Engine

WARNING: This page is about a different variant/trim than selected.

For information on Ford Color Coded Illustrations refer to OEM COLOR CODING .

Special Tool(s) / General Equipment 

GFD235141Courtesy of FORD MOTOR COMPANY
303-1246 Engine Spreader Bar, TKIT-2006UF-FLM, TKIT-2006UF-ROW
GFD235142Courtesy of FORD MOTOR COMPANY
303-1634 Lift Eyes (2), TKIT-2014D-ROW3, TKIT-2014D-FL_ROW
GFD235143Courtesy of FORD MOTOR COMPANY
307-346 (T97T-7902-A) Retainer, Torque Converter, TKIT-1998-LM (NavigatoR), TKIT-1997-F/FLM/LT
Floor Crane
Adjustable Mounting Arm
Hose Clamp Remover/Installer
Powertrain Jack
Wooden Block

Materials 

Name Specification
Motorcraft ® Multi-Purpose Grease Spray XL-5-A ESB-M1C93-B
  1. Lubricate the torque converter hub with multi-purpose grease. Remove Special Service Tool: 307-346 (T97T-7902-A) Retainer, Torque Converter.

    Material: Motorcraft ® Multi-Purpose Grease Spray / XL-5-A (ESB-M1C93-B)

    GFD235490Courtesy of FORD MOTOR COMPANY
    • Inspect the torque converter stud and flexplate for paint marks.

    • Align the torque converter stud and flexplate hole near the paint marks to the 12 o'clock position.

    GFD235491Courtesy of FORD MOTOR COMPANY
  2. Position the engine onto the transmission and subframe assembly. Use the General Equipment: Floor Crane.
    GFD235197Courtesy of FORD MOTOR COMPANY
    • Align the engine to the transmission and install the bolts.

    • Draw the engine and transmission together evenly using the bolts.

    GFD235492Courtesy of FORD MOTOR COMPANY
  3. Install the transmission bellhousing bolts.
    GFD235493Courtesy of FORD MOTOR COMPANY
  4. Tighten.

    Torque: 35 lb.ft (48 Nm)

    GFD235494Courtesy of FORD MOTOR COMPANY
  5. If equipped, install the transmission bellhousing bolt.

    Torque: 35 lb.ft (48 Nm)

    GFD235195Courtesy of FORD MOTOR COMPANY
  6. Install the transmission bellhousing bolts.

    Torque: 35 lb.ft (48 Nm)

    GFD235194Courtesy of FORD MOTOR COMPANY
  7. Install. Use the General Equipment: Adjustable Mounting Arm.
    GFD235495Courtesy of FORD MOTOR COMPANY
    1. Remove the floor crane and length of chain with connecting links. Use the General Equipment: Floor Crane.
    2. Remove Special Service Tool: 303-1246 Engine Spreader Bar., 303-1634 Lift Eyes (2).
    GFD235496Courtesy of FORD MOTOR COMPANY
  8. Using the bolts, draw the PTU up to the transmission.

    Torque: 66 lb.ft (90 Nm)

    GFD235497Courtesy of FORD MOTOR COMPANY
  9. Attach the PTU vent hose retainer.
    GFD235188Courtesy of FORD MOTOR COMPANY
  10. Install the heat shield and the bolts.

    Torque: 97 lb.in (11 Nm)

    GFD235187Courtesy of FORD MOTOR COMPANY
  11. Install the heat shield and the bolts.

    Torque: 97 lb.in (11 Nm)

    GFD235186Courtesy of FORD MOTOR COMPANY
  12. Attach the wiring harness retainers.
    GFD235185Courtesy of FORD MOTOR COMPANY
  13. Attach the coolant tube retainers to the subframe.
    GFD235184Courtesy of FORD MOTOR COMPANY
  14. NOTE: Using the crankshaft pulley bolt, turn the engine clockwise.

    Install the new torque converter nuts.

    Torque: 35 lb.ft (48 Nm)

    GFD235498Courtesy of FORD MOTOR COMPANY
  15. Install the access cover and the retainers.
    GFD235182Courtesy of FORD MOTOR COMPANY
  16. Install the ground cable and the bolt.

    Torque: 89 lb.in (10 Nm)

    GFD234893Courtesy of FORD MOTOR COMPANY
  17. Install the starter and the stud bolts.

    Torque: 35 lb.ft (48 Nm)

    GFD235181Courtesy of FORD MOTOR COMPANY
  18. Install the bracket and the nuts.

    Torque: 17 lb.ft (23 Nm)

    GFD235180Courtesy of FORD MOTOR COMPANY
  19. NOTE: Make sure that when installing the manual control lever, it is fully seated onto the manual control lever shaft. Damage to the manual control lever shaft will occur and the manual lever will come loose.
    NOTE: Make sure to hold the manual control lever while tightening the manual control lever nut or damage to the manual control lever and park components will occur.

    Install the manual control lever and the nut.

    Torque: 159 lb.in (18 Nm)

    GFD235179Courtesy of FORD MOTOR COMPANY
    1. Attach the wiring harness retainers.
    2. Connect the starter electrical connector.
    3. Connect the starter cable and install the nut.

      Torque: 106 lb.in (12 Nm)

    4. Position the starter cable protective cover.
    GFD235499Courtesy of FORD MOTOR COMPANY
    • Connect the transmission electrical connector.

    • Attach the wiring harness retainers.

    GFD235177Courtesy of FORD MOTOR COMPANY
  20. Attach the wiring harness retainers and install the bolt.

    Torque: 71 lb.in (8 Nm)

    GFD235176Courtesy of FORD MOTOR COMPANY
    1. Connect the generator cable and install the nut.

      Torque: 159 lb.in (18 Nm)

    2. Position the generator cable protective cover.
    3. Connect the generator electrical connector.
    GFD235500Courtesy of FORD MOTOR COMPANY
  21. Install a new RH catalytic converter gasket.
    GFD234961Courtesy of FORD MOTOR COMPANY
    1. Install the RH catalytic converter.
    2. Install new RH catalytic converter nuts.

      Torque: 30 lb.ft (40 Nm)

    GFD234962Courtesy of FORD MOTOR COMPANY
    1. Install.

      Torque: 22 lb.ft (30 Nm)

    2. Tighten.

      Torque: 35 lb.ft (48 Nm)

    GFD234963Courtesy of FORD MOTOR COMPANY
  22. Connect the RHHO2S and RH catalyst monitor sensor electrical connectors.
    GFD234927Courtesy of FORD MOTOR COMPANY
  23. Using the powertrain jack, raise the powertrain and subframe assembly into the engine compartment. Use the General Equipment: Powertrain Jack.
    GFD235501Courtesy of FORD MOTOR COMPANY
  24. Install the transmission mount bolts.

    Torque: 59 lb.ft (80 Nm)

    GFD235502Courtesy of FORD MOTOR COMPANY
  25. NOTE: Hand tighten fasteners only at this time.

    1. Install the engine mount.
    2. Install the bracket.
    3. Install the engine mount-to-engine nuts and hand tighten.
    4. Install the engine mount-to-frame bolts and hand tighten.
    5. Install the engine mount-to-frame nut and hand tighten.
    6. Install the bracket nuts and hand tighten.

    GFD235014Courtesy of FORD MOTOR COMPANY
  26. Tighten the engine mount-to-engine nuts.

    Torque: 52 lb.ft (70 Nm)

    GFD235015Courtesy of FORD MOTOR COMPANY
  27. NOTE: Align the reference marks made during removal.
    NOTE: Only tighten the bolts finger tight at this stage.

    Install the new subframe bolts.

    GFD235503Courtesy of FORD MOTOR COMPANY
  28. NOTE: Align the reference marks made during removal.
    NOTE: Only tighten the bolts finger tight at this stage.

    1. Install the subframe brackets and the new subframe bolts.
    2. Install the subframe bracket bolts.

    GFD234980Courtesy of FORD MOTOR COMPANY
  29. NOTE: While tightening the subframe bolts, make sure the front subframe does not move.

    Tighten the subframe bolts.

    Torque: 173 lb.ft (235 Nm)

    GFD235503Courtesy of FORD MOTOR COMPANY
    1. Tighten.

      Torque:

      Stage 1: 76 lb.ft (103 Nm)

      Stage 2: 270 °

    2. Tighten.

      Torque: 35 lb.ft (48 Nm)

    GFD234980Courtesy of FORD MOTOR COMPANY
  30. NOTE: Left hand side.

    Install the bolts and nuts.

    Torque: 173 lb.ft (235 Nm)

    GFD235504Courtesy of FORD MOTOR COMPANY
  31. Remove. Use the General Equipment: Adjustable Mounting Arm.
    GFD235495Courtesy of FORD MOTOR COMPANY
  32. Install the engine-to-transmission bolt.

    Torque: 35 lb.ft (48 Nm)

    GFD235169Courtesy of FORD MOTOR COMPANY
  33. Remove. Use the General Equipment: Powertrain Jack Use the General Equipment: Wooden Block.
    GFD235168Courtesy of FORD MOTOR COMPANY
    1. Tighten the engine mount-to-frame bolts.

      Torque: 81 lb.ft (110 Nm)

    2. Tighten the engine mount-to-frame nut.

      Torque: 81 lb.ft (110 Nm)

    GFD235016Courtesy of FORD MOTOR COMPANY
  34. Tighten the bracket nuts.

    Torque: 177 lb.in (20 Nm)

    GFD235017Courtesy of FORD MOTOR COMPANY
  35. Install the cooling module support panel and the bolts.

    Torque: 177 lb.in (20 Nm)

    GFD234979Courtesy of FORD MOTOR COMPANY
  36. Tighten.

    Torque: 66 lb.ft (90 Nm)

    GFD235505Courtesy of FORD MOTOR COMPANY
  37. Install the rear driveshaft. Refer to: Rear Driveshaft - 3.0L EcoBoost .
  38. Connect the coolant tube. Use the General Equipment: Hose Clamp Remover/Installer.
    GFD235165Courtesy of FORD MOTOR COMPANY
  39. Connect the coolant tubes and attach the retainer.
    GFD235164Courtesy of FORD MOTOR COMPANY
  40. Install the following items:

    1. Refer to: Catalytic Converter LH .
    2. Refer to: Exhaust Flexible Pipe .
    3. NOTE: Do not allow the brake caliper and anchor plate assembly to hang from the brake hose or damage to the hose can occur.

      LH brake disc. Refer to: Brake Disc .

    4. RH front halfshaft. Refer to: Front Halfshaft RH - 3.0L EcoBoost, All-Wheel Drive (AWD) .

  41. Install the subframe support bracket and the nuts.

    Torque: 33 lb.ft (45 Nm)

    GFD234975Courtesy of FORD MOTOR COMPANY
  42. NOTE: Use the internal or external hex-holding feature to prevent the ball and stud from turning while removing or installing the stabilizer bar link nuts. The link boot seal must not be allowed to twist while tightening the link nuts or damage to the boot seal will occur.

    Position the RH sway bar link and install the new nut.

    Torque: 85 lb.ft (115 Nm)

    GFD235025Courtesy of FORD MOTOR COMPANY
  43. NOTE: Use the internal or external hex-holding feature to prevent the ball and stud from turning while removing or installing the stabilizer bar link nuts. The link boot seal must not be allowed to twist while tightening the link nuts or damage to the boot seal will occur.

    Position the LH sway bar link and install the new nut.

    Torque: 85 lb.ft (115 Nm)

    GFD235506Courtesy of FORD MOTOR COMPANY
  44. Install the LH anti-lock sensor and the bolt.

    Torque: 80 lb.in (9 Nm)

    GFD235162Courtesy of FORD MOTOR COMPANY
  45. Install the front ride height sensors. Refer to: Front Suspension Height Sensor .
    1. Position the A/C line bracket onto the generator stud.
    2. Attach the wiring harness retainer.
    GFD235507Courtesy of FORD MOTOR COMPANY
  46. Install the generator nut.

    Torque: 35 lb.ft (47 Nm)

    GFD234964Courtesy of FORD MOTOR COMPANY
  47. Connect the LH engine harness electrical connector and attach the wiring harness retainer to the subframe.
    GFD235160Courtesy of FORD MOTOR COMPANY
  48. Connect the transmission fluid cooler tube.
    GFD235508Courtesy of FORD MOTOR COMPANY
  49. Install the transmission fluid cooler tube secondary latch.
    GFD235158Courtesy of FORD MOTOR COMPANY
  50. Connect the transmission fluid cooler tube.
    GFD235509Courtesy of FORD MOTOR COMPANY
  51. Install the transmission fluid cooler tube secondary latch.
    GFD235156Courtesy of FORD MOTOR COMPANY
    1. Position the high-pressure fuel pump noise insulator aside and connect the high-pressure fuel pump fuel feed tube quick release coupling. Refer to: Quick Release Coupling .
    2. Connect the EVAP tube quick release coupling. Refer to: Quick Release Coupling .
    GFD235155Courtesy of FORD MOTOR COMPANY
    1. Install the ground wire and the bolt.

      Torque: 159 lb.in (18 Nm)

    2. Attach the wiring harness retainers.
    GFD235103Courtesy of FORD MOTOR COMPANY
    1. Install the heater hose and clamp. Use the General Equipment: Hose Clamp Remover/Installer.
    2. Attach the heater hose retainer.
    3. Connect the lower radiator hose. Use the General Equipment: Hose Clamp Remover/Installer.
    4. Connect the engine mount electrical connector.
    GFD235510Courtesy of FORD MOTOR COMPANY
  52. Install the coolant hose and tighten the clamp.

    Torque: 44 lb.in (5 Nm)

    GFD235153Courtesy of FORD MOTOR COMPANY
    1. Position the coolant hose assembly and connect the coolant hose quick connectors.
    2. Attach the coolant hose retainer to the stud bolt.
    GFD235152Courtesy of FORD MOTOR COMPANY
    1. Attach the cable to the transmission control lever.
    2. Position the cable and install the bolt.

      Torque: 62 lb.in (7 Nm)

    GFD235151Courtesy of FORD MOTOR COMPANY
  53. Connect the vacuum tube quick release couplings. Refer to: Quick Release Coupling .
    GFD235042Courtesy of FORD MOTOR COMPANY
  54. Install the bolt and attach the wiring harness retainers.

    Torque: 106 lb.in (12 Nm)

    GFD235150Courtesy of FORD MOTOR COMPANY
  55. Install the battery feed cables and the nuts.

    Torque: 80 lb.in (9 Nm)

    GFD235149Courtesy of FORD MOTOR COMPANY
  56. Install the cover.
    GFD235148Courtesy of FORD MOTOR COMPANY
  57. Install the battery feed cable to the positive battery cable and install the nut.

    Torque: 80 lb.in (9 Nm)

    GFD235147Courtesy of FORD MOTOR COMPANY
  58. Position back the ground cable and install the stud bolt.

    Torque: 80 lb.in (9 Nm)

    GFD235146Courtesy of FORD MOTOR COMPANY
  59. Install the following items:

    1. Refer to: Battery Tray .
    2. Refer to: Air Conditioning (A/C) Compressor - 3.0L EcoBoost .
    3. Refer to: Accessory Drive Belt .

  60. Install the upper CAC outlet pipe and tighten the clamps.

    Torque: 48 lb.in (5.4 Nm)

    GFD235031Courtesy of FORD MOTOR COMPANY
  61. Install the following items:

    1. Refer to: Charge Air Cooler (CAC) Intake Pipe .
    2. Refer to: Air Cleaner Outlet Pipe RH .
    3. Refer to: Air Cleaner Outlet Pipe LH .
    4. Refer to: Oil Cooler .
    5. Refer to: Degas Bottle .

  62. Attach the wiring harness retainer to the engine mount.
    GFD235055Courtesy of FORD MOTOR COMPANY
    • Connect the engine wiring harness electrical connector and retainer.

    • Connect the PCM electrical connector.

    GFD235054Courtesy of FORD MOTOR COMPANY
  63. If equipped, install the wiring harness cover and the retainer.
    GFD235053Courtesy of FORD MOTOR COMPANY
    1. Position the engine appearance cover and attach the 2 grommets onto the ball studs.
    2. Install the nut.

      Torque: 42 lb.in (4.8 Nm)

    GFD235030Courtesy of FORD MOTOR COMPANY
  64. Install the front air deflectors.
    GFD233322Courtesy of FORD MOTOR COMPANY
  65. Install the underbody shield and the retainers.
    GFD233321Courtesy of FORD MOTOR COMPANY
  66. Install the front fender splash shields. Refer to: Fender Splash Shield .
    • Remove the cable ties or the mechanics wire.

    • Install the upper cooling support brackets.

    GFD235511Courtesy of FORD MOTOR COMPANY
    • Install the radiator sight shield and the retainers.

    • Attach the block heater wiring harness and the retainers.

    GFD234972Courtesy of FORD MOTOR COMPANY
  67. Position steering column shaft and install a new bolt.

    Torque: 18 lb.ft (25 Nm)

    GFD235512Courtesy of FORD MOTOR COMPANY
  68. Remove the holding device.
    GFD233721Courtesy of FORD MOTOR COMPANY
  69. Install a new engine oil filter and fill the engine with clean engine oil. Refer to: Engine Oil Draining and Filling .
  70. Connect the battery ground cable. Refer to: Battery Disconnect and Connect .
  71. Fill and bleed the engine cooling system. Refer to: Cooling System Draining, Vacuum Filling and Bleeding .
  72. Charge the A/C system. Refer to: Air Conditioning (A/C) System Recovery, Evacuation and Charging .
  73. Check the transmission fluid level. Refer to: Transmission Fluid Level Check - 3.0L EcoBoost .
  74. Use the Powertrain Control Module (PCM) Misfire Monitor Profile Correction routine in the diagnostic scan tool.