Inspection and Verification
- Verify the customer concern.
- Visually inspect the following for obvious signs of electrical damage.VISUAL INSPECTION CHART
Electrical - Battery junction box (BJB) fuse(s):
- 7 (40A) (no communication with power running board module)
- 8 (40A) (no communication with climate controlled seat module)
- 35 (20A) (no communication with 4WD control module)
- 36 (10A) (no communication with PCM)
- 37 (15A) (no communication with TCM)
- 43 (20A) (no communication with 4WD control module)
- 45 (30A) (no communication with DSM)
- 47 (30A) (no communication with air suspension module)
- 65 (10A) (no communication with air suspension module)
- 73 (5A) (no communication with TCM)
- 76 (20A) (no communication with PCM)
- 77 (10A) (no communication with ABS module)
- Smart junction box (SJB) fuse(s):
- 2 (15A) (no communication with DSM)
- 3 (15A) (no communication with satellite radio receiver, auxiliary audio module, DVD)
- 5 (10A) (no communication with SJB)
- 14 (10A) (no communication with power liftgate module)
- 15 (10A) (no communication with electronic manual temperature control module, EATC module)
- 20 (15A) (no power to scan tool)
- 26 (10A) (no communication with instrument cluster)
- 27 (20A) (no communication with SJB)
- 28 (5A) (no communication with audio unit)
- 29 (5A) (no communication with instrument cluster)
- 32 (10A) (no communication with RCM)
- 35 (10A) (no communication with parking aid module)
- 37 (10A) (no communication with Electronic manual temperature control module, EATC module)
- 38 (20A) (no communication with THX® amplifier)
- 39 (20A) (no communication with audio unit)
- 40 (20A) (no communication with THX® amplifier)
- Data link connector (DLC)
- Wiring harness
- Circuitry
- Battery junction box (BJB) fuse(s):
- If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
- If the cause is not visually evident, connect the scan tool to the DLC.
If the scan tool does not communicate with the VCM:
- Check the VCM connection to the vehicle.
- Check the scan tool connection to the VCM.
- Go to Pinpoint Test W , to diagnose no power to the scan tool.
- Carry out the network test.
- If the network test passes, retrieve and record the continuous memory DTCs and proceed to Step 6.
- If the network test fails, go to Symptom Chart to identify the module not communicating.
- If the DTCs retrieved are related to the concern, go to the Communication Network Diagnostic Trouble Code (DTC) Chart. For all other DTCs, refer to MULTIFUNCTION ELECTRONIC MODULES article.
- If no DTCs related to the concern are retrieved, go to Symptom Chart .
NOTE:
Make sure to use the latest scan tool software release.
NOTE:
The vehicle communication module (VCM) LED prove-out confirms power and ground from the DLC are provided to the VCM.
NOTE:
During the network test, the scan tool will first attempt to communicate with the PCM, after establishing communication with the PCM, the scan tool will then attempt to communicate with all other modules on the vehicle.
NOTE:
DTC U1900 will set in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module.
COMMUNICATION NETWORK DIAGNOSTIC TROUBLE CODES (DTC) CHART
| DTC | Description | Source | Action |
|---|---|---|---|
| U0001 | High Speed CAN Communication Bus Off | Anti-lock brake system (ABS) module | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0073 | Control Module Communication Bus Off | Air suspension module | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0073 | Control Module Communication Bus Off | Transmission control module (TCM) | The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U0100 | Lost Communication With ECM/PCM | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test A . |
| U0100 | Lost Communication With ECM/PCM | Air suspension module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test A . |
| U0100 | Lost Communication With ECM/PCM | Instrument cluster | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test A . |
| U0100 | Lost Communication With ECM/PCM | TCM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test A . |
| U0100 | Lost Communication With ECM/PCM | Four wheel drive (4WD) control module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test A . |
| U0101 | Lost Communication With TCM | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test B . |
| U0101 | Lost Communication With TCM | Instrument cluster | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test B . |
| U0101 | Lost Communication With TCM | 4WD control module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test B |
| U0102 | Lost Communication With Transfer Case Control Module (4x4CM) | Instrument cluster | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test E . |
| U0102 | Lost Communication With Transfer Case Control Module (4x4CM) | TCM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test E . |
| U0114 | Lost Communication With Four-Wheel Drive Control Module | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test E . |
| U0121 | Lost Communication With Anti-Lock Brake System (ABS) Control Module | Instrument cluster | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test C . |
| U0121 | Lost Communication With Anti-Lock Brake System (ABS) Control Module | TCM | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test C . |
| U0121 | Lost Communication With Anti-Lock Brake System (ABS) Control Module | 4WD control module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test C . |
| U0122 | Lost Communication With Vehicle Dynamics Control Module | Instrument cluster | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test F . |
| U0140 | Lost Communication With Body Control Module (GEM) | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test H . |
| U0140 | Lost Communication With Body Control Module (GEM) | Air suspension module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test H . |
| U0140 | Lost Communication With Body Control Module (GEM) | Audio unit | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0140 | Lost Communication With Body Control Module (GEM) | Auxiliary audio module | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0140 | Lost Communication With Body Control Module (GEM) | Driver seat module (DSM) | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test H . |
| U0140 | Lost Communication With Body Control Module (GEM) | DVD player | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0140 | Lost Communication With Body Control Module (GEM) | Instrument cluster | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test H . |
| U0140 | Lost Communication With Body Control Module (GEM) | Parking aid module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test H . |
| U0140 | Lost Communication With Body Control Module (GEM) | Power liftgate module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test H . |
| U0151 | Lost Communication With Restraints Control Module | Instrument cluster | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test D . |
| U0155 | Lost Communication With Instrument Panel Cluster (IC) Control Module | ABS module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test G . |
| U0155 | Lost Communication With Instrument Panel Cluster (IC) Control Module | Air suspension module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test G . |
| U0155 | Lost Communication With Instrument Panel Cluster (IC) Control Module | Audio unit | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0155 | Lost Communication With Instrument Panel Cluster (IC) Control Module | DSM | RETRIEVE and FOLLOW non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULES article. |
| U0155 | Lost Communication With Instrument Panel Cluster (IC) Control Module | Parking aid module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test G . |
| U0155 | Lost Communication With Instrument Panel Cluster (IC) Control Module | Power liftgate module | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test G . |
| U0155 | Lost Communication With Instrument Panel Cluster (IC) Control Module | Smart junction box | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test G . |
| U0155 | Lost Communication With Instrument Panel Cluster (IC) Control Module | THX® amplifier | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0159 | Lost Communication With Parking Assist Control Module (PAM) | Audio unit | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test S . |
| U0159 | Lost Communication With Parking Assist Control Module (PAM) | Instrument cluster | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test S . |
| U0164 | Lost Communication With HVAC Control Module (EATC) | Instrument cluster | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test I . |
| U0184 | Lost Communication With Radio (ACM) | Auxiliary audio module | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0184 | Lost Communication With Radio (ACM) | Digital versatile disc (DVD) player | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0184 | Lost Communication With Radio (ACM) | Satellite radio receiver | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0184 | Lost Communication With Radio (ACM) | THX® amplifier | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0193 | Lost Communication With Digital Audio Control Module (SDARS) | Audio unit | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0193 | Lost Communication With Digital Audio Control Module (SDARS) | Auxiliary audio module | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0193 | Lost Communication With Digital Audio Control Module (SDARS) | DVD player | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0196 | Lost Communication With Entertainment Control Module - Rear (AUX) | Audio unit | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0196 | Lost Communication With Entertainment Control Module - Rear (AUX) | Satellite radio receiver | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0196 | Lost Communication With Entertainment Control Module - Rear (AUX) | THX® amplifier | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0208 | Lost Communication With Seat Control Module | Instrument cluster | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test P . |
| U0230 | Lost Communication With Rear Gate Module (LTM) | Instrument cluster | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test T . |
| U0238 | Lost Communication With Digital Audio Control Module "D" (DSP) | Audio unit | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0244 | Lost Communication With Running Board Control Module (PRB) | Instrument cluster | CLEAR the DTC. REPEAT the network test with the scan tool. If the DTC returns, go to Pinpoint Test R . |
| U0249 | Lost Communication With Entertainment Control Module - Rear "B" (RCU) | Audio unit | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0249 | Lost Communication With Entertainment Control Module - Rear "B" (RCU) | Satellite radio receiver | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0255 | Lost Communication With Front Controls Interface Module | Satellite radio receiver | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0256 | Lost Communication With Front Display Interface Module | Satellite radio receiver | REFER to INFORMATION AND ENTERTAINMENT SYSTEMS article. |
| U0401 | Invalid Data Received from ECM/PCM A | ABS module | RETRIEVE and FOLLOW DTCs from the PCM. |
| U0402 | Invalid Data Received from TCM | ABS module | RETRIEVE and FOLLOW DTCs from the TCM. |
| U0414 | Invalid Data Received from 4WD module | ABS module | RETRIEVE and FOLLOW DTCs from the 4WD control module. |
| U0415 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module | 4WD control module | RETRIEVE and FOLLOW DTCs from the ABS module. |
| U1900 | CAN Communication Bus Fault-Receive Error | Power running board module | Go to Symptom Chart for module that failed network test. |
| U1900 | CAN Communication Bus Fault-Receive Error | Restraints control module (RCM) | Go to Symptom Chart for module that failed network test. |
| U1900 | CAN Communication Bus Fault-Receive Error | 4WD | Go to Symptom Chart for module that failed network test. |
| U1901 | CAN Network #2 Communication Bus Fault - Receive Error | ABS | REFER to VEHICLE DYNAMIC SYSTEMS article. |
| U2011 | Module Transmitted Invalid Data (Non SCP) | Air suspension module | RETRIEVE and FOLLOW non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULES article. |
| U2013 | Compass Module is not Responding | Instrument cluster | REFER to INFORMATION AND MESSAGE CENTER article. |
| U2023 | Fault Received From External Node | Instrument cluster | U2023 is set when a module receives invalid network data from another module with a faulted input. RETRIEVE and REPAIR all non-network DTCs in the other modules on the network. REFER to MULTIFUNCTION ELECTRONIC MODULES article for a list of all DTCs. |
| U2023 | Fault Received From External Node | Parking aid module | U2023 is set when a module receives invalid network data from another module with a faulted input. RETRIEVE and REPAIR all non-network DTCs in the other modules on the network. REFER to MULTIFUNCTION ELECTRONIC MODULES article for a list of all DTCs. |
| U2023 | Fault Received From External Node | 4WD | U2023 is set when a module receives invalid network data from another module with a faulted input. RETRIEVE and REPAIR all non-network DTCs in the other modules on the network. REFER to MULTIFUNCTION ELECTRONIC MODULES article for a list of all DTCs. |
| U2471 | Unexpected PRNDL State | DSM | RETRIEVE and FOLLOW non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULES article. |
| U2471 | Unexpected PRNDL State | Parking aid module | RETRIEVE and FOLLOW non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULES article. |
| U2471 | Unexpected PRNDL State | Power liftgate module | RETRIEVE and FOLLOW non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULES article. |
| U2472 | Unexpected Ignition State | Instrument cluster | RETRIEVE and FOLLOW non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULES article. |
| U2472 | Unexpected Ignition State | Parking aid module | RETRIEVE and FOLLOW non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULES article. |
| U2472 | Unexpected Ignition State | Power liftgate module | RETRIEVE and FOLLOW non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULES article. |
| U2472 | Unexpected Ignition State | Smart junction box (SJB) | RETRIEVE and FOLLOW non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULES article. |
| U2473 | Unexpected Vehicle Speed (VSS) | Audio unit | RETRIEVE and FOLLOW non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULES article. |
| U2473 | Unexpected Vehicle Speed (VSS) | Parking aid module | RETRIEVE and FOLLOW non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULES article. |
| U2473 | Unexpected Vehicle Speed (VSS) | Power liftgate module | RETRIEVE and FOLLOW non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULES article. |
| U2473 | Unexpected Vehicle Speed (VSS) | SJB | RETRIEVE and FOLLOW non-network DTCs from other modules. REFER to MULTIFUNCTION ELECTRONIC MODULES article. |