LEMON Manuals: Even more car manuals for everyone

Extension Housing Gasket: Removal

  1. Position the vehicle on a hoist. Place in NEUTRAL. For additional information, refer to JACKING & HOISTING .
  2. NOTE: The output shaft and driveshaft are a balanced assembly.
    Fig 1: Marking Driveshaft Flange
    G01335885Courtesy of FORD MOTOR CO.
  3. Mark the driveshaft flange and the rear pinion flange for correct alignment during assembly.
  4. Remove the four driveshaft bolts.
    Fig 2: Locating Driveshaft Bolts
    G01335886Courtesy of FORD MOTOR CO.
  5. Index mark the driveshaft and extension housing. Separate the driveshaft from the transmission.
    Fig 3: Removing Driveshaft From Extension Housing
    G01335887Courtesy of FORD MOTOR CO.
  6. Remove the rear transmission insulator nuts.
    Fig 4: Locating Rear Transmission Insulator Nuts
    G01335888Courtesy of FORD MOTOR CO.
  7. Disconnect the RH HO2S sensor connector.
    Fig 5: Locating Right HO2S Connector
    G01335889Courtesy of FORD MOTOR CO.
  8. Disconnect the RH catalyst monitor connector.
    Fig 6: Locating Right Catalyst Monitor Connector
    G01335890Courtesy of FORD MOTOR CO.
  9. Remove the bolts from the RH exhaust flange.
    Fig 7: Locating Right Exhaust Flange Bolts
    G01335891Courtesy of FORD MOTOR CO.
  10. Loosen the exhaust clamp and remove the RH exhaust pipe.
    Fig 8: Removing Right Exhaust Pipe
    G01335892Courtesy of FORD MOTOR CO.
  11. Disconnect the LH HO2S sensor connector.
    Fig 9: Locating Left HO2S Connector
    G01335893Courtesy of FORD MOTOR CO.
  12. Disconnect the LH catalyst monitor connector.
    Fig 10: Locating Left Catalyst Monitor Connector
    G01335894Courtesy of FORD MOTOR CO.
  13. Remove the bolts from the LH exhaust flange.
    Fig 11: Locating Left Exhaust Flange Bolts
    G01335895Courtesy of FORD MOTOR CO.
  14. Loosen the exhaust clamp and remove the LH exhaust pipe.
    Fig 12: Removing Left Exhaust Pipe
    G01335896Courtesy of FORD MOTOR CO.
  15. Install a suitable transmission jack.
  16. Remove the RH side crossmember bolts.
    Fig 13: Locating Right Crossmember Bolts
    G01335897Courtesy of FORD MOTOR CO.
  17. Disconnect the LH side crossmember.
    1. Loosen but do not remove the LH side crossmember bolts.
    2. Remove the LH side crossmember bolt.
    Fig 14: Locating Left Crossmember Bolts
    G01335898Courtesy of FORD MOTOR CO.
  18. Remove the bolts and remove the parking brake cable bracket and position aside.
    Fig 15: Locating Parking Brake Cable Bracket Bolts
    G01335899Courtesy of FORD MOTOR CO.
  19. NOTE: The crossmember is a press fit in the crossmember pocket, it may be necessary to pry the crossmember out of the crossmember pocket. Be careful not to damage the crossmember. Only the RH side of the crossmember will need to be lowered in order to gain access to the rear extension housing.
    Fig 16: Lowering Right Side Of Crossmember
    G01335900Courtesy of FORD MOTOR CO.
  20. Lower the RH side of the crossmember.
  21. Remove the rear transmission insulator bolts.
    Fig 17: Locating Rear Transmission Insulator Bolts
    G01335901Courtesy of FORD MOTOR CO.
  22. Remove the LH and RH catalyst monitor connector retainers.
    Fig 18: Locating Catalyst Monitor Connector Retainers
    G01335902Courtesy of FORD MOTOR CO.
  23. Remove the rear extension housing bolts and the housing.
    Fig 19: Locating Rear Extension Housing Bolts
    G01335903Courtesy of FORD MOTOR CO.
  24. Remove the extension housing gasket.
    Fig 20: Locating Rear Extension Housing Gasket
    G01335904Courtesy of FORD MOTOR CO.