LEMON Manuals: Even more car manuals for everyone

Section 399 (Engine): Assembly: Engine: Assembly

WARNING: This page is about a different car, the 2004 Lincoln Town Car. However, it is still accessible from the selected car via links, so may be relevant.

    All Engines 

  1. Record the main bearing code found on the front of the engine block.
    Fig 1: Locating Main Bearing Code - Engine Block
    G03248285Courtesy of FORD MOTOR CO.
  2. Record the main bearing code found on the back of the crankshaft.
    Fig 2: Locating Main Bearing Code - Crankshaft
    G03248286Courtesy of FORD MOTOR CO.
  3. Using the data recorded earlier and the Bearing Select Fit Chart, Standard Bearings Chart determine the required bearing grade for each main bearing.
    • Read the first letter of the engine block main bearing code and the first letter of the crankshaft main bearing code.
    • Read down the column below the engine main bearing code letter, and across the row next to the crankshaft main bearing code letter, until the two intersect. This is the required bearing grade for the number one crankshaft main bearing.
    • As an example, if the engine block code letter is "F" and the crankshaft code letter is "D," the correct bearing grade for this main bearing is "2."
    • Repeat this process for the remaining four main bearings.
    Fig 3: Bearing Select Fit Chart - Standard Bearings
    G03248287Courtesy of FORD MOTOR CO.
  4. If oversize bearings are being used, use the procedure in the previous step and the Bearing Select Fit Chart, Oversize Bearing Chart to determine the required grade for each main bearing.
    Fig 4: Bearing Select Fit Chart - Oversize Bearings
    G03248288Courtesy of FORD MOTOR CO.
  5. CAUTION: Before assembling the cylinder block, all sealing surfaces must be free of chips, dirt, paint and foreign material. Also, make sure the coolant and oil passages are clear.
  6. Lubricate with clean engine oil and install the crankshaft upper main bearings into the cylinder block.
  7. Install the crankshaft onto the upper crankshaft thrust bearing and main bearings.
    Fig 5: Installing Crankshaft Onto Upper Crankshaft Thrust Bearing And Main Bearings
    G03248289Courtesy of FORD MOTOR CO.
  8. NOTE: To aid in assembly, apply petroleum jelly to the back of the crankshaft thrust washer.
    NOTE: The oil groove on the thrust washer must face toward the rear of the engine (crankshaft surface).
    Fig 6: Installing Rear Main Bearing Cap
    G03248290Courtesy of FORD MOTOR CO.
  9. Install the rear main bearing cap.
  10. Install the crankshaft lower main bearings, thrust bearing and thrust washer into the main bearing caps. Locate the main bearing cap on the cylinder block and tap into place using a plastic or dead-blow hammer.
    Fig 7: Installing Crankshaft Lower Main Bearings
    G03248291Courtesy of FORD MOTOR CO.
  11. NOTE: The jack screws are a part of the main bearing cap assembly, and are screwed into the main caps, not the cylinder block.
    Fig 8: Backing Out Jack Screws
    G03248292Courtesy of FORD MOTOR CO.
  12. Back out the jack screws against the cylinder block in two stages, in the sequence shown.
    • Stage 1: Tighten to 5 Nm (44 lb-in).
    • Stage 2: Tighten to 10 Nm (89 lb-in).
  13. Install the bolts and tighten in two stages, in the sequence shown.
    • Stage 1: Tighten to 10 Nm (89 lb-in).
    • Stage 2: Tighten to 21 Nm (15 lb-ft).
    Fig 9: Identifying Cross-Mounted Main Cap Bolts Tightening Sequence
    G03248293Courtesy of FORD MOTOR CO.
  14. Tighten the bolts in two stages, in the sequence shown.
    • Stage 1: Tighten to 40 Nm (30 lb-ft).
    • Stage 2: Tighten an additional 90 degrees.
    Fig 10: Identifying Main Cap Bolts Tightening Sequence
    G03248294Courtesy of FORD MOTOR CO.
  15. Check piston-to-cylinder block and ring clearances. For additional information, refer to ENGINE SYSTEM-GENERAL INFORMATION .
  16. CAUTION: Do not scratch the cylinder walls or crankshaft journals with the connecting rod.
    NOTE: Make sure the piston arrow is facing forward.
    NOTE: The next three steps are for all eight connecting rods, rod caps and pistons. Only one connecting rod, rod cap and piston is shown.
    Fig 11: Installing Piston And Connecting Rod Assemblies
    G03248295Courtesy of FORD MOTOR CO.
  17. Use the special tools to install the piston and connecting rod assemblies.
    • Lubricate the piston and ring with clean engine oil.
    • Lubricate the rod bearings with clean engine oil.
    • Rotate the crankshaft as necessary.
  18. CAUTION: Do not scratch the cylinder walls or crankshaft journals with the connecting rod.
    Fig 12: Removing Special Tool
    G03248296Courtesy of FORD MOTOR CO.
  19. Once the connecting rod is seated on the crankshaft journal, remove the special tools.
  20. CAUTION: The rod cap installation must keep the same orientation as marked during disassembly.
    NOTE: The connecting rod caps are of the cracked design and must make mate with the connecting rod ends. Excessive bearing clearance will result if not mated correctly.
    Fig 13: Positioning Lower Bearing And Connecting Rod Cap
    G03248297Courtesy of FORD MOTOR CO.
  21. Position the lower bearing and connecting rod cap, and install the new bolts loosely.
  22. Tighten the bolts in two stages, in the sequence shown.
    • Stage 1: Tighten to 43 Nm (32 lb-ft).
    • Stage 2: Rotate an additional 90-120 degrees.
    Fig 14: Identifying Connecting Rod Cap Bolts Tightening Sequence
    G03248298Courtesy of FORD MOTOR CO.
  23. Position the oil pump and install the bolts loosely. Tighten the bolts in the sequence shown.
    Fig 15: Identifying Oil Pump Bolts Tightening Sequence
    G03248299Courtesy of FORD MOTOR CO.
  24. Both Cylinder Heads 

    CAUTION: The gasket sealing surfaces on the cylinder head and cylinder block must be clean. For additional information, refer to CYLINDER HEADS .
    CAUTION: The use of sealing aids (aviation cement, copper spray and glue) is not permitted. The gasket must be installed dry.
    CAUTION: The new gasket has a film coating which is crucial to the gasket's ability to seat correctly. Do not scratch the gasket.
    NOTE: RH head gasket shown; LH head gasket similar.
    Fig 16: Installing Head Gasket Over Dowel Pins
    G03248300Courtesy of FORD MOTOR CO.
  25. Install the head gasket over the dowel pins.
  26. CAUTION: Cylinder head machining or milling is not authorized by the Ford Motor Company. Cylinder head flatness must be within 0.0254 mm (0.001 in) across a 38.1 mm (1.5 in) square area.
    CAUTION: The gasket sealing surfaces on the cylinder head and cylinder block must be clean. For additional information, refer to CYLINDER HEADS .
    CAUTION: The use of sealing aids (aviation cement, copper spray and glue) is not permitted. The gasket must be installed dry.
    CAUTION: Do not allow the dowels to scratch the sealing of the cylinder head during cylinder head installation.
    NOTE: The new cylinder head bolts must be lightly oiled with a rag, and allowed to drain for a few minutes prior to installation.
    NOTE: RH cylinder head shown; LH cylinder head similar.
    Fig 17: Installing Cylinder Head
    G03248301Courtesy of FORD MOTOR CO.
  27. Install the cylinder head on the dowels and the head gasket. Loosely install new bolts.
  28. Tighten the cylinder head bolts in six stages, in the sequence shown.
    1. Stage 1: Tighten to 40 Nm (30 lb-ft).
    2. Stage 2: Tighten an additional 90 degrees (1/4 turn).
    3. Stage 3: Loosen the bolts a minimum of one full turn (360 degrees).
    4. Stage 4: Tighten to 40 Nm (30 lb-ft).
    5. Stage 5: Tighten an additional 90 degrees (1/4 turn).
    6. Stage 6: Tighten an additional 90 degrees (1/4 turn).
    Fig 18: Identifying Cylinder Head Bolts Tightening Sequence
    G03248302Courtesy of FORD MOTOR CO.
  29. Remove the special tools from both ends of the cylinder head.
    Fig 19: Removing Special Tools From Both Ends Of Cylinder Head
    G03248303Courtesy of FORD MOTOR CO.
  30. NOTE: Lubricate the hydraulic lash adjusters with clean engine oil.
    Fig 20: Installing Hydraulic Lash Adjusters
    G03248304Courtesy of FORD MOTOR CO.
  31. Install the hydraulic lash adjusters in their original locations.
  32. NOTE: Lubricate the O-ring seal with clean engine oil.
    Fig 21: Installing Oil Level Indicator Tube
    G03248305Courtesy of FORD MOTOR CO.
  33. Install the oil lever indicator tube.
    • Install a new O-ring seal on the oil level indicator tube.
  34. Install the LH exhaust manifold.
    • Install a new LH exhaust manifold gasket.
    • Install the LH exhaust manifold.
    • Tighten the nuts in the sequence shown.
    Fig 22: Installing LH Exhaust Manifold
    G03248306Courtesy of FORD MOTOR CO.
  35. Install the RH exhaust manifold.
    • Install a new RH exhaust manifold gasket.
    • Install the RH exhaust manifold.
    • Tighten the nuts in the sequence shown.
    Fig 23: Installing RH Exhaust Manifold
    G03248307Courtesy of FORD MOTOR CO.
  36. Engines With Ratcheting Timing Chain Tensioners 

    CAUTION: Timing chain procedures must be followed exactly or damage to valves and pistons will result.
    CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
    NOTE: LH shown; RH similar.
    Fig 24: Compressing Tensioner Plunger
    G03248308Courtesy of FORD MOTOR CO.
  37. Compress each tensioner plunger, using an edge or a vise.
  38. Using a small screwdriver or pick, push back and hold the ratchet mechanism.
    Fig 25: Pushing Back And Holding Ratchet Mechanism
    G03248309Courtesy of FORD MOTOR CO.
  39. While holding the ratchet mechanism, push the ratchet arm back into the tensioner housing.
    Fig 26: Pushing Ratchet Arm Back Into Tensioner Housing
    G03248310Courtesy of FORD MOTOR CO.
  40. Install a paper clip into the hole of each tensioner housing to hold the ratchet assembly and plunger in during installation.
    • Remove the tensioner from the vise.
    Fig 27: Retaining Ratchet Assembly & Plunger
    G03248311Courtesy of FORD MOTOR CO.
  41. Engines With Non-Ratcheting Timing Chain Tensioners 

    CAUTION: Timing chain procedures must be followed exactly or damage to valves and pistons will result.
    NOTE: LH shown; RH similar.
    Fig 28: Compressing Tensioner Plunger
    G03248312Courtesy of FORD MOTOR CO.
  42. Compress each tensioner plunger, using a vise.
  43. Install a retaining clip on the tensioner to hold the plunger in during installation.
    Fig 29: Installing Retaining Clip On Tensioner
    G03248313Courtesy of FORD MOTOR CO.
  44. All Engines 

  45. If the copper links are not visible, mark one link on one end and one link on the other end, and use as timing marks.
    Fig 30: Locating/Marking Timing Chain Links
    G03248314Courtesy of FORD MOTOR CO.
  46. Using the special tool, position the crankshaft.
    • Remove the special tool after crankshaft positioning.
    Fig 31: Positioning Crankshaft
    G03248315Courtesy of FORD MOTOR CO.
  47. Install the crankshaft sprocket, making sure the flange faces forward.
    Fig 32: Identifying Correct Crankshaft Sprocket Installation
    G03248316Courtesy of FORD MOTOR CO.
  48. Install the timing chain guides.
    1. Position the LH timing chain guide.
    2. Install and tighten the LH bolts.
    3. Position the RH timing chain guide.
    4. Install and tighten the RH bolts.
    Fig 33: Installing Timing Chain Guides
    G03248317Courtesy of FORD MOTOR CO.
  49. Rotate the RH camshaft sprocket until the timing mark is approximately at the 11 o'clock position. Rotate the LH camshaft sprocket until the timing mark is approximately at the 12 o'clock position.
    Fig 34: Identifying Proper Camshaft Sprocket Timing Mark Positions
    G03248318Courtesy of FORD MOTOR CO.
  50. Position the LH (inner) timing chain on the crankshaft sprocket, aligning the copper (marked) link with the timing mark on the sprocket.
    Fig 35: Aligning Copper (Marked) Link With Timing Mark On Crankshaft Sprocket
    G03248319Courtesy of FORD MOTOR CO.
  51. Install the LH timing chain on the camshaft sprocket, aligning the copper (marked) link with the timing marks on the sprocket.
    Fig 36: Aligning Copper (Marked) Link With Timing Marks On LH Camshaft Sprocket
    G03248320Courtesy of FORD MOTOR CO.
  52. NOTE: The LH timing chain tensioner arm has a bump near the dowel hole for identification.
    Fig 37: Installing LH Timing Chain Tensioner
    G03248321Courtesy of FORD MOTOR CO.
  53. Position the LH timing chain tensioner on the dowel pin and install the LH timing chain tensioner.
  54. Engines With Ratcheting Timing Chain Tensioners 

  55. Remove the retaining clip from the LH timing chain tensioner.
    Fig 38: Removing Retaining Clip From LH Timing Chain Tensioner
    G03248322Courtesy of FORD MOTOR CO.

    Engines With Non-Ratcheting Timing Chain Tensioners 

  56. Remove the retaining clip from the LH timing chain tensioner.
    Fig 39: Removing Retaining Clip From LH Timing Chain Tensioner
    G03248323Courtesy of FORD MOTOR CO.
  57. All Engines 

  58. Position the RH (outer) timing chain on the crankshaft sprocket, aligning the copper (marked) link with the timing mark on the sprocket.
    Fig 40: Aligning Copper (Marked) Link With Timing Mark On Crankshaft Sprocket
    G03248324Courtesy of FORD MOTOR CO.
  59. Install the RH timing chain on the camshaft sprocket, aligning the copper (marked) link with the timing marks on the sprocket.
    Fig 41: Aligning Copper (Marked) Link With Timing Marks On RH Camshaft Sprocket
    G03248325Courtesy of FORD MOTOR CO.
  60. Position the RH timing chain tensioner arm on the dowel pin and install the RH timing chain tensioner.
    Fig 42: Installing RH Timing Chain Tensioner
    G03248326Courtesy of FORD MOTOR CO.
  61. Engines With Ratcheting Timing Chain Tensioners 

  62. Remove the retaining clip from the RH timing chain tensioner.
    Fig 43: Removing Retaining Clip From RH Timing Chain Tensioner
    G03248327Courtesy of FORD MOTOR CO.
  63. Engines With Non-Ratcheting Timing Chain Tensioners 

  64. Remove the retaining clip from the RH timing chain tensioner.
    Fig 44: Removing Retaining Clip From RH Timing Chain Tensioner
    G03248328Courtesy of FORD MOTOR CO.
  65. All Engines 

  66. Make sure that the copper (marked) chain links are lined up with the dots on the crankshaft sprockets and the camshaft sprocket.
    Fig 45: Identifying Copper (Marked) Chain Links Position
    G03248329Courtesy of FORD MOTOR CO.
  67. Rotate and camshaft until the lobe is in the up position.
    Fig 46: Identifying Camshaft Lobe Position
    G03248330Courtesy of FORD MOTOR CO.
  68. Install the special tool between the valve spring coil to prevent valve stem seal damage.
    Fig 47: Installing Special Tool Between Valve Spring Coil
    G03248331Courtesy of FORD MOTOR CO.
  69. NOTE: Lubricate the camshaft roller followers using clean engine oil.
    NOTE: Position the cam lobe away from the camshaft roller follower location prior to installing each camshaft roller follower.
    Fig 48: Installing Camshaft Roller Followers
    G03248332Courtesy of FORD MOTOR CO.
  70. Install the camshaft roller followers.
    1. Install the special tool.
    2. Compress the valve spring.
    3. Install the camshaft roller followers in their original locations.
  71. Remove the special tool.
    Fig 49: Removing Special Tool
    G03248333Courtesy of FORD MOTOR CO.
  72. Install all eight spark plugs.
    Fig 50: Installing Spark Plugs
    G03248334Courtesy of FORD MOTOR CO.
  73. Install the crankshaft sensor ring.
    Fig 51: Installing Crankshaft Sensor Ring
    G03248335Courtesy of FORD MOTOR CO.
  74. NOTE: RH timing chain removed for clarity.
    NOTE: If the engine front cover is not secured within four minutes, the sealant must be removed and the sealing area cleaned with metal surface cleaner. Allow to dry until there is no sign of wetness, or four minutes, whichever is longer. Failure to follow this procedure can cause future oil leakage.
    Fig 52: Identifying Engine Front Cover Sealant Locations
    G03248336Courtesy of FORD MOTOR CO.
  75. Apply a bead of sealant along the head-to-block surface and the oil pan-to-block surface as specified.
  76. Install a new engine front cover gasket on the engine front cover. Position the engine front cover. Install the fasteners finger-tight.
    Fig 53: Installing Engine Front Cover
    G03248337Courtesy of FORD MOTOR CO.
  77. Tighten the front cover fasteners in the sequence shown to 25 Nm (18 lb-ft).
    Fig 54: Identifying Engine Front Cover Fasteners Tightening Sequence
    G03248338Courtesy of FORD MOTOR CO.
  78. NOTE: RH shown; LH similar.
    Fig 55: Installing Engine Mounts
    G03248339Courtesy of FORD MOTOR CO.
  79. Install the RH and LH engine mounts.
  80. Lubricate the engine front cover and the front oil seal inner lip with clean engine oil.
    Fig 56: Lubricating Engine Front Cover And Front Oil Seal Inner Lip
    G03248340Courtesy of FORD MOTOR CO.
  81. Using the special tools, install the front oil seal.
    Fig 57: Installing Front Oil Seal
    G03248341Courtesy of FORD MOTOR CO.
  82. NOTE: If not secured within four minutes, sealant must be removed and the sealing area cleaned with metal surface cleaner. Allow to dry until there is no sign of wetness, or four minutes, whichever is longer. Failure to follow this procedure can cause future oil leakage.
    Fig 58: Applying Sealant To Woodruff Key Slot On Crankshaft Pulley
    G03248342Courtesy of FORD MOTOR CO.
  83. Apply sealant to the Woodruff key slot on the crankshaft pulley.
  84. Using the special tool, install the crankshaft pulley.
    Fig 59: Installing Crankshaft Pulley
    G03248343Courtesy of FORD MOTOR CO.
  85. NOTE: Use special tool 303 -009 or suitable strap wrench to hold the pulley.
    Fig 60: Tightening Crankshaft Pulley Bolt
    G03248344Courtesy of FORD MOTOR CO.
  86. Tighten the crankshaft pulley bolt in four stages.
    • Stage 1: Tighten to 90 Nm (66 lb-ft).
    • Stage 2: Loosen 360 degrees.
    • Stage 3: Tighten to 50 Nm (37 lb-ft).
    • Stage 4: Rotate an additional 90 degrees (1/4 turn).
  87. NOTE: If the rear crankshaft seal retaining plate is not secured within four minutes, the sealant must be removed and the sealing area cleaned with metal surface cleaner. Allow to dry until there is no sign of wetness, or four minutes, whichever is longer. Failure to follow this procedure can cause future oil leakage.
    NOTE: The silicone must be applied on the groove along the retainer plate.
    Fig 61: Applying Sealant Around Rear Oil Seal Retainer Sealing Surface
    G03248345Courtesy of FORD MOTOR CO.
  88. Apply a 4 mm (0.16 in) bead of silicone gasket and sealant around the rear oil seal retainer sealing surface.
  89. Install the rear oil seal retainer and loosely install the six bolts.
    Fig 62: Installing Rear Oil Seal Retainer
    G03248346Courtesy of FORD MOTOR CO.
  90. Tighten the bolts in the sequence shown.
    Fig 63: Identifying Rear Oil Seal Retainer Bolts Tightening Sequence
    G03248347Courtesy of FORD MOTOR CO.
  91. CAUTION: Make sure the O-ring seal is in place and not damaged. A missing or damaged O-ring seal can cause foam in the lubrication system, low oil pressure and severe engine damage.
    NOTE: Clean and inspect the mating surfaces and install a new O-ring seal. Lubricate the O-ring seal with clean engine oil.
    Fig 64: Installing Oil Pump Screen Cover And Tube Spacer
    G03248348Courtesy of FORD MOTOR CO.
  92. Install the oil pump screen cover and tube spacer.
  93. Position the oil pump screen cover and tube, and install the bolts.
    Fig 65: Installing Oil Pump Screen Cover & Tube
    G03248349Courtesy of FORD MOTOR CO.
  94. NOTE: If the oil pan is not secured within four minutes, the sealant must be removed and the sealing areas cleaned with metal surface cleaner. Allow to dry until there is no sign of wetness, or four minutes, whichever is longer. Failure to follow this procedure can cause future oil leakage.
    Fig 66: Identifying Silicone Application Locations - Rear Oil Seal Retainer-To-Cylinder Block Surface
    G03248350Courtesy of FORD MOTOR CO.
  95. Apply the sealant at the rear oil seal retainer to cylinder block sealing surface.
  96. Apply sealant at the front cover-to-cylinder block sealing surface.
    Fig 67: Identifying Silicone Application Locations - Engine Front Cover-To-Cylinder Block Surface
    G03248351Courtesy of FORD MOTOR CO.
  97. Position the oil pan gasket, the oil pan and the bolts on the engine.
  98. Tighten the bolts in two stages, in the sequence shown.
    1. Stage 1: Tighten to 20 Nm (15 lb-ft).
    2. Stage 2: Rotate an additional 60 degrees.
    Fig 68: Oil Pan Bolts Tightening Sequence
    G03248353Courtesy of FORD MOTOR CO.
  99. Install the oil filter adapter.
    Fig 69: Installing Oil Filter Adapter
    G03248354Courtesy of FORD MOTOR CO.
  100. CAUTION: Do not rotate the coolant pump housing once the coolant pump has been positioned in the cylinder block. Damage to the O-ring seal will occur.
    Fig 70: Installing Coolant Pump
    G03248355Courtesy of FORD MOTOR CO.
  101. Install the coolant pump.
    1. Lubricate the new O-ring seal using engine coolant.
    2. Position the coolant pump into the engine block.
    3. Install the bolts.
  102. Position the coolant pump pulley on the coolant pump and install the bolts.
    Fig 71: Installing Coolant Pump Pulley
    G03248356Courtesy of FORD MOTOR CO.
  103. Position the belt idler pulley and install the bolt.
    Fig 72: Installing Idler Pulley
    G03248357Courtesy of FORD MOTOR CO.
  104. NOTE: If not secured within four minutes, sealant must be removed and the sealing area cleaned with metal surface cleaner. Allow to dry until there is no sign of wetness, or four minutes, whichever is longer. Failure to follow this procedure can cause future oil leakage.
    Fig 73: Identifying LH Valve Cover Sealant Locations
    G03248358Courtesy of FORD MOTOR CO.
  105. Apply sealant in two places where the engine front cover meets the cylinder head.
  106. Install the gasket into the valve cover and position on the cylinder head. Tighten the bolts in the sequence shown.
    Fig 74: Identifying LH Valve Cover Bolts Tightening Sequence
    G03248359Courtesy of FORD MOTOR CO.
  107. NOTE: If not secured within four minutes, sealant must be removed and the sealing area cleaned with metal surface cleaner. Allow to dry until there is no sign of wetness, or four minutes, whichever is longer. Failure to follow this procedure can cause future oil leakage.
    Fig 75: Identifying RH Valve Cover Sealant Locations
    G03248360Courtesy of FORD MOTOR CO.
  108. Apply sealant in two places where the engine front cover meet the cylinder head.
  109. Install the gasket into the valve cover and position on the cylinder head. Tighten the bolts in the sequence shown.
    Fig 76: Identifying RH Valve Cover Bolts Tightening Sequence
    G03248361Courtesy of FORD MOTOR CO.
  110. Install the knock sensor (KS) and the bolts.
    Fig 77: Installing Knock Sensor (KS)
    G03248362Courtesy of FORD MOTOR CO.
  111. Inspect the O-rings seals. Install new seals if necessary.
    Fig 78: Inspecting O-Rings Seals
    G03248363Courtesy of FORD MOTOR CO.
  112. Install the coolant bypass tube.
    Fig 79: Installing Coolant Bypass Tube
    G03248364Courtesy of FORD MOTOR CO.
  113. Install the ground strap on the rear of the RH cylinder head.
    1. Install the stud bolt.
    2. Install the ground strap.
    3. Install the retaining nut.
    Fig 80: Installing Ground Strap On Rear Of RH Cylinder Head
    G03248365Courtesy of FORD MOTOR CO.
  114. NOTE: Align the gasket locator tabs to slots in cylinder head.
    Fig 81: Installing Intake Manifold Gaskets
    G03248366Courtesy of FORD MOTOR CO.
  115. Install new intake manifold gaskets.
  116. Install the intake manifold and hand-tighten the bolts at the locations shown.
    Fig 82: Installing Intake Manifold
    G03248367Courtesy of FORD MOTOR CO.
  117. Install the eight ignition coils and tighten the eight bolts.
    Fig 83: Tightening Ignition Coils
    G03248368Courtesy of FORD MOTOR CO.
  118. Install the crash bracket and loosely install the bolt and the stud.
    Fig 84: Installing Bolt And Stud
    G03248369Courtesy of FORD MOTOR CO.
  119. Install the thermostat.
    Fig 85: Installing Thermostat
    G03248370Courtesy of FORD MOTOR CO.
  120. Install the coolant outlet adapter and loosely install the bolts.
    Fig 86: Installing Coolant Outlet Adapter
    G03248371Courtesy of FORD MOTOR CO.
  121. Tighten the bolts in the sequence shown.
    Fig 87: Identifying Intake Manifold Bolts Tightening Sequence
    G03248372Courtesy of FORD MOTOR CO.
  122. Tighten the stud.
    Fig 88: Tightening Stud
    G03248373Courtesy of FORD MOTOR CO.
  123. Tighten the bolts.
    Fig 89: Tightening Coolant Outlet Adapter Bolts
    G03248374Courtesy of FORD MOTOR CO.
  124. Install the throttle body and tighten the bolts.
    Fig 90: Installing Throttle Body
    G03248375Courtesy of FORD MOTOR CO.
  125. Install the throttle return spring.
    Fig 91: Installing Throttle Return Spring
    G03248376Courtesy of FORD MOTOR CO.
  126. Connect the exhaust gas recirculation (EGR) tube to the EGR valve.
    Fig 92: Connecting Exhaust Gas Recirculation (EGR) Tube To EGR Valve
    G03248377Courtesy of FORD MOTOR CO.
  127. Connect the EGR tube to the exhaust manifold connector.
    Fig 93: Connecting EGR Tube To Exhaust Manifold Connector
    G03248378Courtesy of FORD MOTOR CO.
  128. Position the fuel charging wiring at two locations at the back of the intake manifold.
  129. Install the generator.
    Fig 94: Installing Generator
    G03248379Courtesy of FORD MOTOR CO.
  130. Connect the electrical connector to the idle air control (IAC) valve and the throttle position (TP) sensor.
    Fig 95: Connecting Electrical Connector To Idle Air Control (IAC) Valve And Throttle Position (TP) Sensor
    G03248380Courtesy of FORD MOTOR CO.
  131. Install the generator mounting bracket.
    Fig 96: Installing Generator Mounting Bracket
    G03248381Courtesy of FORD MOTOR CO.
  132. Connect the generator electrical connector, generator cable and harness pin-type retainer.
    Fig 97: Connecting Generator Electrical Connector, Generator Cable And Harness Pin-Type Retainer
    G03248382Courtesy of FORD MOTOR CO.
  133. Position the vacuum harness and connect the vacuum hoses for the evaporative emission (EVAP) canister purge valve, the main chassis hose and the EGR valve.
    Fig 98: Connecting Vacuum Hoses For Evaporative Emission (EVAP) Canister Purge Valve
    G03248383Courtesy of FORD MOTOR CO.
  134. Install the generator wiring harness anchor to the LH front stud.
    Fig 99: Installing Generator Wiring Harness Anchor To LH Front Stud
    G03248384Courtesy of FORD MOTOR CO.
  135. Connect the engine coolant temperature (ECT) sensor electrical connector.
    Fig 100: Connecting Engine Coolant Temperature (ECT) Sensor Electrical Connector
    G03248385Courtesy of FORD MOTOR CO.
  136. Connect the crankcase ventilation tube.
    Fig 101: Connecting Crankcase Ventilation Tube
    G03248386Courtesy of FORD MOTOR CO.
  137. Install the EGR tube heat shield.
    Fig 102: Installing EGR Tube Heat Shield
    G03248387Courtesy of FORD MOTOR CO.
  138. Connect the eight fuel injector electrical connectors.
    Fig 103: Connecting Eight Fuel Injector Electrical Connectors
    G03248388Courtesy of FORD MOTOR CO.
  139. Connect the eight ignition coil electrical connectors.
    Fig 104: Connecting Eight Ignition Coil Electrical Connectors
    G03248389Courtesy of FORD MOTOR CO.
  140. Connect the camshaft position (CMP) sensor electrical connector.
    Fig 105: Connecting Camshaft Position (CMP) Sensor Electrical Connector
    G03248390Courtesy of FORD MOTOR CO.
  141. Connect the radio interference capacitor electrical connector.
    Fig 106: Connecting Radio Interference Capacitor Electrical Connector
    G03248391Courtesy of FORD MOTOR CO.
  142. Connect the KS electrical connector and install the harness retainer to the intake manifold.
    Fig 107: Installing Harness Retainer To Intake Manifold
    G03248392Courtesy of FORD MOTOR CO.
  143. Connect the cylinder head temperature (CHT) sensor electrical connector.
    Fig 108: Connecting Cylinder Head Temperature (CHT) Sensor Electrical Connector
    G03248393Courtesy of FORD MOTOR CO.
  144. Connect the ground wire to the right rear fuel rail stud.
    Fig 109: Connecting Ground Wire To Right Rear Fuel Rail Stud
    G03248394Courtesy of FORD MOTOR CO.
  145. Install the battery cables and the bolt.
  146. NOTE: RH shown; LH similar.
    Fig 110: Installing Lifting Brackets
    G03248395Courtesy of FORD MOTOR CO.
  147. Install the RH and LH lighting brackets.
  148. Remove the engine from the engine stand.
    Fig 111: Removing Engine From Engine Stand
    G03248396Courtesy of FORD MOTOR CO.
  149. Using the special tool, install the crankshaft rear oil seal.
    Fig 112: Installing Crankshaft Rear Oil Seal
    G03248397Courtesy of FORD MOTOR CO.
  150. Using the special tools, install the crankshaft oil slinger.
    Fig 113: Installing Crankshaft Oil Slinger
    G03248398Courtesy of FORD MOTOR CO.
  151. Install the engine/transmission spacer plate.
    Fig 114: Installing Engine/Transmission Spacer Plate
    G03248399Courtesy of FORD MOTOR CO.
  152. Position the flexplate and install the bolts in the sequence shown.
    Fig 115: Identifying Flexplate Bolts Tightening Sequence
    G03248400Courtesy of FORD MOTOR CO.