LEMON Manuals: Even more car manuals for everyone

Inspection [08/2015 - ]: Procedure

  1. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY 
    1. Remove the magnets and use them to collect steel particles.
    2. Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.
      • Steel (magnetic): bearing, gear and clutch plate wear
      • Brass (non-magnetic): bush wear
  2. INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY 
    GTY618668Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Hold the reverse clutch hub and turn the 1-way clutch assembly.
    2. Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.
      TEXT IN ILLUSTRATION

      Free
      Lock

      If there is a problem with the 1-way clutch, replace the No. 2 1-way clutch assembly.

  3. INSPECT REAR CLUTCH DISC 
    GTY127055Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
      NOTE:

      Before assembling new discs, soak them in ATF for at least 15 minutes.

  4. INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY 
    GTY107765Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a dial indicator, measure the inside diameter of the reverse clutch hub bush.

      Standard inside diameter

      35.812 to 35.837 mm (1.410 to 1.411 in.)

      1. If the inside diameter is not as specified, replace the reverse clutch hub.
  5. INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY 
    1. Using a dial indicator, measure the inside diameter of the forward clutch hub bush.
      GTY107771Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard inside diameter

      26.037 to 26.062 mm (1.025 to 1.026 in.)

      1. If the inside diameter is not as specified, replace the forward clutch hub.
  6. INSPECT UNDERDRIVE 1-WAY CLUTCH ASSEMBLY 
    GTY648192Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Hold the coast clutch hub and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.
      TEXT IN ILLUSTRATION

      Free
      Lock

      If there is a problem with the 1-way clutch, replace the underdrive 1-way clutch assembly.

  7. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC 
    GTY110302Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
      NOTE:

      Before assembling new discs, soak them in ATF for at least 15 minutes.

  8. INSPECT COAST CLUTCH DISC 
    GTY130123Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
      NOTE:

      Before assembling new discs, soak them in ATF for at least 15 minutes.

  9. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY 
    GTY110301Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

      Standard free length

      24.64 mm (0.970 in.)

      If the free length is less than the standard, replace the forward clutch return spring sub-assembly.

  10. INSPECT DIRECT CLUTCH DISC 
    GTY110300Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
      NOTE:

      Before assembling new discs, soak them in ATF for at least 15 minutes.

  11. INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY 
    GTY130122Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

      Standard free length

      21.04 mm (0.828 in.)

      If the free length is less than the standard, replace the reverse clutch return spring sub-assembly.

  12. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY 
    GTY110299Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

      Standard free length

      19.51 mm (0.768 in.)

      If the free length is less than the standard, replace the direct clutch return spring sub-assembly.

  13. INSPECT NO. 3 BRAKE DISC 
    GTY110297Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
      NOTE:

      Before assembling new discs, soak them in ATF for at least 15 minutes.

  14. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY 
    GTY280974Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

      Standard free length

      15.72 mm (0.619 in.)

      If the free length is less than the standard, replace the No. 3 brake piston return spring sub-assembly.

  15. INSPECT FRONT PLANETARY GEAR ASSEMBLY 
    GTY102174Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a feeler gauge, measure the front planetary pinion gear thrust clearance.

      Standard clearance

      0.2 to 0.60 mm (0.00787 to 0.0236 in.)

      1. If the clearance is not as specified, replace the front planetary gear assembly.
    2. Using a cylinder gauge, measure the inside diameter of the front planetary gear bush.
      GTY107794Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard inside diameter

      57.405 to 57.43 mm (2.260 to 2.261 in.)

      1. If the inside diameter is not as specified, replace the front planetary gear.
  16. INSPECT 1-WAY CLUTCH ASSEMBLY 
    GTY618669Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Install the 1-way clutch to the 1-way clutch inner race.
    2. Hold the 1-way clutch inner race and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.
      TEXT IN ILLUSTRATION

      Free
      Lock

      If there is a problem with the 1-way clutch, replace the 1-way clutch assembly.

    3. Remove the 1-way clutch from the 1-way clutch inner race.
  17. INSPECT NO. 1 BRAKE DISC 
    GTY280972Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
      NOTE:

      Before assembling new discs, soak them in ATF for at least 15 minutes.

  18. INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY 
    GTY280975Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

      Standard free length

      17.05 mm (0.671 in.)

      If the free length is less than the standard, replace the brake piston return spring sub-assembly.

  19. INSPECT NO. 2 BRAKE DISC 
    1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
      GTY130113Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Before assembling new discs, soak them in ATF for at least 15 minutes.

  20. INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY 
    1. Using a vernier caliper, measure the free length of the spring together with the spring seat.
      GTY280919Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard free length

      22.66 mm (0.892 in.)

      If the free length is less than the standard, replace the No. 2 brake piston return spring sub-assembly.

  21. INSPECT CENTER PLANETARY GEAR ASSEMBLY 
    1. Using a feeler gauge, measure the center planetary gear pinion thrust clearance.
      GTY107790Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard clearance

      0.12 to 0.68 mm (0.00472 to 0.0268 in.)

      1. If the clearance is not as specified, replace the center planetary gear assembly.
  22. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY 
    GTY618688Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Hold the rear planetary ring gear flange and turn the 1-way clutch. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.
      TEXT IN ILLUSTRATION

      Free
      Lock

      If there is a problem with the 1-way clutch, replace the No. 3 1-way clutch assembly.

  23. INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY 
    1. Using a dial indicator, measure the inside diameter of the rear planetary ring gear bush.
      GTY289508Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard inside diameter

      32.176 to 32.201 mm (1.267 to 1.268 in.)

      1. If the inside diameter is not as specified, replace the rear planetary ring gear.
  24. INSPECT INTERMEDIATE SHAFT 
    1. Using a dial indicator, measure the intermediate shaft runout.
      GTY107787Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Maximum runout

      0.08 mm (0.00315 in.)

      If the runout is not as specified, replace the intermediate shaft with a new one.

    2. Using a micrometer, check the outer diameter of the intermediate shaft at the positions shown in the diagram.
      GTY613012Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard diameter

      A, B 

      25.962 to 25.975 mm (1.022 to 1.023 in.)

      C, D 

      32.062 to 32.075 mm (1.262 to 1.263 in.)

      If the outer diameter is not as specified, replace the intermediate shaft with a new one.

  25. INSPECT NO. 4 BRAKE DISC 
    1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
      GTY130147Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Before assembling new discs, soak them in ATF for at least 15 minutes.

  26. INSPECT REAR PLANETARY GEAR ASSEMBLY 
    GTY110291Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a feeler gauge, measure the rear planetary gear pinion thrust clearance.

      Standard clearance

      0.2 to 0.6 mm (0.00787 to 0.0236 in.)

      1. If the clearance is not as specified, replace the planetary gear assembly.
    2. Using a dial indicator, measure the inside diameter of the rear planetary gear bush.
      GTY588196Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard inside diameter

      20.0 to 20.025 mm (0.787 to 0.788 in.)

      1. If the inside diameter is not as specified, replace the rear planetary gear assembly.
  27. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY 
    GTY280918Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

      Standard free length

      23.74 mm (0.935 in.)

      If the free length is less than the standard, replace the 1st and reverse brake return spring sub-assembly.

  28. INSPECT INDIVIDUAL PISTON OPERATION 
    1. Check the operating sound while applying compressed air into the oil holes indicated in the illustration.
      GTY634743Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      When inspecting the rear clutch, check the operating sound with the C3 accumulator piston hole closed.

      If there is no sound, disassemble and check the installation condition of the parts.

      1. Forward multiple disc clutch (C1)
      2. Direct clutch (C2)
      3. Rear clutch (C3)
      4. Coast clutch (C4)
      5. No. 1 brake (B1)
      6. No. 2 brake (B2)
      7. No. 3 brake (B3)
      8. No. 4 brake (B4)