LEMON Manuals: Even more car manuals for everyone

Disassembly [08/2015 - ]: Procedure

  1. REMOVE TRANSMISSION CONTROL SHAFT LEVER LH 
    GTY661096Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the nut, spring washer and control shaft lever LH.
  2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY 
    1. Using a screwdriver, bend the tabs of the lock washer.
      GTY611014Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the nut, lock washer and bolt.
    3. Remove the park/neutral position switch.

      HINT: 

      Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.

  3. REMOVE OIL COOLER TUBE UNION 
    GTY272613Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 2 oil cooler tube unions.
    2. Remove the O-ring from each oil cooler tube union.
  4. REMOVE SPEED SENSOR 
    GTY547111Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 2 bolts and 2 speed sensors.
    2. Remove the O-ring from each sensor.
  5. REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE 
    GTY288977Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 2 bolts.
    2. Remove the breather tube.
    3. Remove the O-ring from the tube.
  6. REMOVE AUTOMATIC TRANSMISSION HOUSING 
    GTY262594Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 10 bolts and transmission housing.
  7. REMOVE REAR TRANSFER ADAPTER 
    GTY680374Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 8 bolts and transfer adapter.

      HINT: 

      Use a brass bar and hammer to remove the transfer adapter.

    2. Using a screwdriver, remove the transfer adapter hole snap ring.
  8. REMOVE TRANSFER CASE ADAPTER REAR OIL SEAL 
    GTY200974Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a screwdriver, pry out the oil seal.
      NOTE:

      Be careful not to damage the transfer adapter.

      HINT: 

      Wrap the tip of the screwdriver with tape.

  9. REMOVE TRANSFER CASE REAR ADAPTER OIL RECEIVER 
    1. Using snap ring pliers, remove the snap ring and oil receiver.
      GTY640206Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY 
    GTY578237Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Install the transmission case to an overhaul attachment.
  11. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY 
    1. Remove the drain plug and gasket.
    2. Remove the overflow plug and gasket.
    3. Remove the 20 bolts and oil pan.
      GTY549670Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Do not turn the transmission over as this will contaminate the valve body with any foreign matter in the bottom of the pan.

  12. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY 

    See step  1

  13. REMOVE VALVE BODY OIL STRAINER ASSEMBLY 
    GTY606630Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Turn over the transmission.
    2. Remove the 4 bolts and oil strainer from the valve body.
    3. Remove the O-ring from the oil strainer.
  14. REMOVE TRANSMISSION WIRE 
    GTY673841Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 2 bolts and 2 temperature sensor clamps.
    2. Disconnect the 2 ATF temperature sensors.
    3. Remove the 2 O-rings from the 2 ATF temperature sensors.
    4. Disconnect the 9 solenoid valve connectors.
    5. Detach the wire harness from the 2 clamps.
    6. Remove the bolt and pull out the transmission wire.
      GTY385062Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Remove the O-ring from the transmission wire connector.
  15. REMOVE TRANSMISSION VALVE BODY ASSEMBLY 
    1. Remove the bolt, detent spring cover and detent spring.
    2. Remove the 19 bolts and valve body.
      GTY631951Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. REMOVE CHECK BALL BODY 
    GTY225064Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the check ball body and spring.
      TEXT IN ILLUSTRATION

      *1 Check Ball Body
      *2 Spring
  17. REMOVE TRANSMISSION CASE GASKET 
    GTY107756Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 3 gaskets.
  18. REMOVE BRAKE DRUM GASKET 
    GTY578192Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 3 gaskets.
  19. REMOVE C-2 ACCUMULATOR PISTON 
    GTY100177Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. While applying compressed air to the oil hole, remove the C-2 accumulator piston and spring.
    2. Remove the 2 O-rings from the piston.
      NOTE:

      Be careful as the C-3 and B-3 accumulator pistons may jump out.

  20. REMOVE B-3 ACCUMULATOR PISTON 
    GTY100177Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. While applying compressed air to the oil hole, remove the B-3 accumulator piston and spring.
    2. Remove the 2 O-rings from the piston.
      NOTE:

      Be careful as the C-3 accumulator piston may jump out.

  21. REMOVE C-3 ACCUMULATOR PISTON 
    GTY107706Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. While applying compressed air to the oil hole, remove the C-3 accumulator piston and 2 springs.
    2. Remove the 2 O-rings from the piston.
  22. REMOVE B-1 ACCUMULATOR VALVE 
    GTY107708Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the B-1 accumulator valve and 2 springs.
  23. REMOVE PARKING LOCK PAWL BRACKET 
    GTY568389Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 3 bolts and bracket.
  24. REMOVE PARKING LOCK ROD SUB-ASSEMBLY 
    GTY568390Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the parking lock rod from the manual valve lever.
  25. REMOVE PARKING LOCK PAWL SHAFT 
    GTY608713Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Pull out the parking lock pawl shaft from the front side to remove it, and then remove the lock pawl and spring.
    2. Remove the E-ring from the shaft.
  26. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY 
    GTY578239Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a hammer and screwdriver, cut off the spacer and remove it from the shaft.
    2. Using a pin punch and hammer, tap out the spring pin.
      GTY578250Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Tap out the spring pin slowly so that it does not fall into the transmission case.

    3. Pull the manual valve lever shaft out through the case and remove the manual valve lever.
  27. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL 
    GTY679235Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a screwdriver, pry out the 2 oil seals.
      NOTE:

      Be careful not to damage the transmission case.

      HINT: 

      Wrap the tip of the screwdriver with tape.

  28. REMOVE OIL PUMP ASSEMBLY 
    GTY100171Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 10 bolts.
    2. Using SST, remove the oil pump.
      GTY673312Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • SST: 09350-30020 
        1. 09350-07020
    3. Remove the 2 thrust bearing races and O-ring from the oil pump.
      GTY110361Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY 
    GTY107710Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the clutch drum and input shaft assembly from the transmission case.
    2. Remove the clutch drum thrust washer and 2 thrust needle roller bearings.
      GTY130619Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  30. INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY 

    See step  2

  31. REMOVE NO. 2 1-WAY CLUTCH ASSEMBLY 
    GTY578174Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the No. 2 1-way clutch and clutch drum thrust washer from the clutch drum and input shaft assembly.
  32. FIX CLUTCH DRUM AND INPUT SHAFT ASSEMBLY 
    GTY284379Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Place the oil pump onto the torque converter clutch, and then place the clutch drum and input shaft assembly onto the oil pump.
  33. REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY 
    GTY110366Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a screwdriver, remove the snap ring.
    2. Remove the reverse clutch reaction sleeve and reverse clutch hub sub-assembly together with the rear clutch disc set from the clutch drum.
      GTY110367Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  34. REMOVE REAR CLUTCH DISC SET 
    1. Remove the clutch cushion plate, reverse clutch flange, 5 discs and 4 plates from the reverse clutch hub.
    2. Remove the reverse clutch flange from the clutch drum.
      GTY110331Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. INSPECT REAR CLUTCH DISC 

    See step  3

  36. INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY 

    See step  4

  37. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY 
    GTY610736Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the thrust needle roller bearing, forward clutch hub and No. 3 clutch hub thrust washer from the clutch drum.
  38. INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY 

    See step  5

  39. REMOVE COAST CLUTCH HUB SUB-ASSEMBLY 
    GTY110369Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 2 thrust needle roller bearings, the coast clutch hub together with the underdrive 1-way clutch and the thrust bearing race from the clutch drum.
  40. INSPECT UNDERDRIVE 1-WAY CLUTCH ASSEMBLY 

    See step  6

  41. REMOVE UNDERDRIVE 1-WAY CLUTCH ASSEMBLY 
    GTY586014Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the underdrive 1-way clutch from the coast clutch hub.
    2. Remove the No. 2 clutch hub thrust washer from the coast clutch hub.
  42. REMOVE FORWARD MULTIPLE DISC CLUTCH DISC SET 
    GTY130577Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a screwdriver, remove the hole snap ring.
    2. Remove the flange, 5 discs and 5 plates from the input shaft.
  43. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC 

    See step  7

  44. REMOVE COAST CLUTCH DISC SET 
    GTY130578Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a screwdriver, remove the hole snap ring.
    2. Remove the flange, 3 discs and 3 plates from the input shaft.
  45. INSPECT COAST CLUTCH DISC 

    See step  8

  46. REMOVE INPUT SHAFT ASSEMBLY 
    GTY586016Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the input shaft from the clutch drum.
  47. REMOVE INPUT SHAFT OIL SEAL RING 
    GTY130576Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 4 oil seal rings from the input shaft.
  48. REMOVE COAST CLUTCH PISTON 
    GTY606347Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Place SST on the No. 1 clutch balancer and compress the return spring with a press.
      • SST: 09350-30020 
        1. 09350-07040
    2. Using SST, remove the snap ring.
      • SST: 09350-30020 
        1. 09350-07070
    3. Remove the No. 1 clutch balancer and forward clutch return spring from the input shaft.
      GTY289417Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the O-ring from the No. 1 clutch balancer.
      GTY110376Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Hold the input shaft by hand and apply compressed air to the input shaft to remove the coast clutch piston.
      GTY110378Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  49. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY 

    See step  9

  50. REMOVE FORWARD CLUTCH PISTON 
    GTY110379Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Hold the input shaft by hand and apply compressed air to the input shaft to remove the forward clutch piston.
    2. Remove the O-ring from the input shaft.
      GTY110247Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  51. REMOVE DIRECT CLUTCH DISC SET 
    GTY110413Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a screwdriver, remove the 2 hole snap rings from the clutch drum.
    2. Remove the direct clutch flange, 6 discs and 6 plates from the clutch drum.
  52. INSPECT DIRECT CLUTCH DISC 

    See step  10

  53. REMOVE NO. 3 CLUTCH BALANCER 
    1. Place SST on the No. 3 clutch balancer and compress the return spring with a press.
      • SST: 09387-00070 
      GTY644024Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using SST, remove the snap ring.
      • SST: 09350-30020 
        1. 09350-07070
    3. Remove the No. 3 clutch balancer.
    4. Remove the reverse clutch return spring and O-ring from the reverse clutch piston sub-assembly.
      GTY110381Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  54. INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY 

    See step  11

  55. REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY 
    GTY110382Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the reverse clutch piston from the clutch drum.
    2. Remove the O-ring from the reverse clutch piston.
      GTY130166Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the O-ring from the clutch drum.
      GTY588207Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  56. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY 
    GTY680533Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Place SST on the direct clutch piston and compress the return spring with a press.
      • SST: 09320-89010 
    2. Using SST, remove the snap ring.
      • SST: 09350-30020 
        1. 09350-07070
    3. Using 2 screwdrivers, remove the direct clutch piston together with the No. 2 clutch balancer and direct clutch return spring sub-assembly.
      GTY104139Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the No. 2 clutch balancer and direct clutch return spring from the direct clutch piston.
      GTY610816Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the 2 O-rings from the direct clutch piston.
      GTY588599Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  57. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY 

    See step  12

  58. REMOVE NO. 3 BRAKE SNAP RING 
    GTY578219Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a screwdriver, remove the No. 3 brake snap ring from the case.
  59. REMOVE NO. 3 BRAKE DISC SET 
    1. Remove the flange, 4 discs, 4 plates and cushion plate from the case.
  60. INSPECT NO. 3 BRAKE DISC 

    See step  13

  61. REMOVE NO. 3 BRAKE PISTON HOLE SNAP RING 
    GTY666023Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using SST, remove the snap ring.
      • SST: 09350-30020 
        1. 09350-07060
  62. REMOVE 1-WAY CLUTCH ASSEMBLY 
    GTY606386Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 1-way clutch assembly and No. 1 planetary carrier thrust washer from the case.
  63. REMOVE NO. 3 BRAKE CYLINDER 
    GTY578222Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the No. 3 brake cylinder from the case.
  64. REMOVE NO. 3 BRAKE PISTON 
    GTY680424Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using SST and a press, compress the return spring and remove the snap ring.
      • SST: 09351-40010 
    2. Hold the No. 3 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2 , 57 psi) to the 2nd brake cylinder to remove the No. 3 brake piston.
      GTY107796Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 2 O-rings from the No. 3 brake piston.
      GTY107798Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  65. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY 

    See step  14

  66. REMOVE FRONT PLANETARY GEAR ASSEMBLY 
    GTY144126Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 1-way clutch inner race and front planetary gear assembly from the case.
    2. Remove the thrust bearing race, thrust needle roller bearing and No. 2 planetary carrier thrust washer from the front planetary gear assembly.
      GTY100230Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  67. INSPECT FRONT PLANETARY GEAR ASSEMBLY 

    See step  15

  68. INSPECT 1-WAY CLUTCH ASSEMBLY 

    See step  16

  69. REMOVE FRONT PLANETARY RING GEAR 
    GTY606385Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the front planetary ring gear and thrust needle roller bearing from the transmission case.
  70. REMOVE CENTER PLANETARY RING GEAR 
    GTY588192Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a screwdriver, remove the snap ring.
    2. Remove the center planetary ring gear and front planetary ring gear flange from the front planetary ring gear.
      GTY588166Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  71. REMOVE NO. 1 BRAKE DISC SET 
    1. Remove the flange, 4 discs and 4 plates from the case.
  72. INSPECT NO. 1 BRAKE DISC 

    See step  17

  73. REMOVE NO. 1 BRAKE PISTON RETURN SPRING SNAP RING 
    GTY107724Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a screwdriver, remove the No. 1 brake piston return spring snap ring from the case.
  74. REMOVE NO. 1 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY 
    GTY578217Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the brake piston return spring and No. 1 brake piston with No. 1 brake cylinder from the case.
  75. INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY 

    See step  18

  76. REMOVE NO. 1 BRAKE PISTON 
    GTY107727Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Hold the No. 1 brake cylinder and apply compressed air (392 kPa (4.0 kgf/cm2 , 57 psi)) to the No. 1 brake cylinder to remove the No. 1 brake piston.

      HINT: 

      If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

    2. Remove the 2 O-rings from the No. 1 brake piston.
  77. REMOVE NO. 2 BRAKE DISC SET 
    GTY100231Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a screwdriver, remove the snap ring from the case.
    2. Remove the flange, 4 discs, 4 plates and brake piston return spring from the case.
  78. INSPECT NO. 2 BRAKE DISC 

    See step  19

  79. INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY 

    See step  20

  80. REMOVE NO. 2 BRAKE PISTON 
    GTY103750Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Hold the No. 2 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2 , 57 psi) to the transmission case to remove the No. 2 brake piston and No. 2 brake cylinder.

      HINT: 

      If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

    2. Remove the 2 O-rings from the No. 2 brake piston.
  81. REMOVE CENTER PLANETARY GEAR ASSEMBLY 
    GTY578212Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the thrust bearing race, center planetary gear and planetary sun gear from the case.
  82. INSPECT CENTER PLANETARY GEAR ASSEMBLY 

    See step  21

  83. REMOVE INTERMEDIATE SHAFT 
    GTY606384Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a screwdriver, remove the snap ring from the case.
    2. Remove the intermediate shaft with No. 3 1-way clutch assembly from the case.
      GTY107730Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  84. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY 

    See step  22

  85. REMOVE NO. 3 1-WAY CLUTCH ASSEMBLY 
    1. Remove the No. 3 1-way clutch assembly and 1-way clutch inner race from the intermediate shaft.
      GTY578194Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  86. REMOVE REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY 
    GTY606379Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the planetary ring gear flange together with the rear planetary ring gear, thrust bearing race, thrust needle roller bearing and thrust bearing race from the intermediate shaft.
    2. Using a screwdriver, remove the snap ring.
      GTY608069Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the rear planetary ring gear flange from the rear planetary ring gear.
  87. INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY 

    See step  23

  88. INSPECT INTERMEDIATE SHAFT 

    See step  24

  89. REMOVE BRAKE PLATE STOPPER SPRING 
    GTY578211Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  90. REMOVE NO. 4 BRAKE DISC SET 
    1. Remove the 2 flanges, 8 discs and 7 plates from the case.
  91. INSPECT NO. 4 BRAKE DISC 

    See step  25

  92. REMOVE REAR PLANETARY GEAR ASSEMBLY 
    GTY606383Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the rear planetary gear assembly from the case.
    2. Remove the thrust needle roller bearing from the rear planetary gear.
      GTY569192Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the thrust bearing race from the case.
      GTY569193Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  93. INSPECT REAR PLANETARY GEAR ASSEMBLY 

    See step  26

  94. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY 
    GTY618555Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Place SST on the spring retainer and compress the brake return spring.
      • SST: 09350-30020 
        1. 09350-07050
    2. Using SST, remove the snap ring and brake return spring.
      • SST: 09350-30020 
        1. 09350-07070
      TEXT IN ILLUSTRATION

      *1 Snap Ring
  95. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY 

    See step  27

  96. REMOVE 1ST AND REVERSE BRAKE PISTON 
    GTY578209Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Apply compressed air (392 kPa, 4.0 kgf/cm2 , 57 psi) to the transmission case to remove the 1st and reverse brake piston.

      HINT: 

      If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

    2. Remove the O-ring from the 1st and reverse brake piston.
  97. REMOVE BRAKE REACTION SLEEVE 
    GTY639101Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using SST, remove the reaction sleeve.
      • SST: 09350-30020 
        1. 09350-07080
    2. Remove the 2 O-rings from the reaction sleeve.
  98. REMOVE NO. 4 BRAKE PISTON 
    GTY644968Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using SST, remove the brake piston.
      • SST: 09350-30020 
        1. 09350-07090
    2. Remove the 2 O-rings from the brake piston.