LEMON Manuals: Even more car manuals for everyone

Removal [09/2014 - 10/2015]: Procedure

  1. REMOVE FUEL PUMP ASSEMBLY 

    (Refer to REMOVAL [09/2014 - 10/2015] )

  2. REMOVE NO. 3 FUEL PIPE SUB-ASSEMBLY 
    1. Remove the 4 bolts and fuel pipe from the fuel delivery pipe sub-assembly.
      GTY416047Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      Front
      NOTE:

      Pull and remove the fuel pipe in a straight line to avoid damage to the seal surface of the delivery pipe O-rings.

    2. Remove the O-rings, backup rings and E-rings from the No. 3 fuel pipe sub-assembly.
  3. REMOVE NO. 2 FUEL DELIVERY PIPE SUB-ASSEMBLY 
    1. Disconnect the 3 wire harness clamps.
      GTY395850Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      Front
    2. Remove the 2 bolts and 2 nuts.
      GTY406290Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Nut
      *2 Bolt
      *a Front
    3. With the connectors still connected, disconnect the No. 2 fuel delivery pipe.
      GTY402787Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      Front
      NOTE:
      • Make sure that the fuel delivery pipe is disconnected from the delivery pipe (LH side).
      • Be extremely careful not to touch or strike the tips of the injectors.
      • Pull and remove the fuel pipe in a straight line without tilting it.
    4. Disconnect the 3 injector connectors.
    5. Remove the 3 injector vibration insulators from the cylinder head.
  4. REMOVE NO. 1 FUEL DELIVERY PIPE SUB-ASSEMBLY 
    1. GTY402836Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Disconnect the fuel pressure sensor connector.

    2. Detach the wire harness clamp.
    3. Disconnect the 2 wire harness clamps.
      GTY395835Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      Front
    4. Remove the 2 bolts and 2 nuts.
      GTY415222Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Nut
      *2 Bolt
      *a Front
    5. With the connectors still connected, disconnect the No. 1 fuel delivery pipe.
      GTY402772Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      Front
      NOTE:
      • Be extremely careful not to touch or strike the tips of the injectors.
      • Pull and remove the fuel pipe in a straight line without tilting it.
    6. Disconnect the 3 injector connectors.
    7. Remove the 3 injector vibration insulators from the cylinder head.
  5. REMOVE FUEL INJECTOR ASSEMBLY 
    1. Secure the delivery pipe in a vise between aluminum plates and pull out the injector in a straight line.
      GTY398942Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Pull and remove the injector in a straight line to avoid damage to the seal surface of the delivery pipe O-ring.
      • For reinstallation, attach a tag or label to the injector shaft.
    2. Remove the nozzle holder clamps from the injectors.
    3. Remove the O-ring, backup rings and E-ring from the fuel injector.
  6. REMOVE FUEL INJECTOR SEAL 
    1. Using the tips of a pair of needle nose pliers, pinch and pull one of the 2 injector seals at several points to stretch it. Repeat this for the other injector seal.
      GTY145307Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Excessively pinching the injector seal may damage the groove of the injector.
      • If an injector is dropped or the tips of the injectors are struck, replace it with a new one.
    2. Remove the 2 injector seals from the injector.