LEMON Manuals: Even more car manuals for everyone

Intermittent Battery Discharge (L-SB-0035-16)

Publication date: 2016-07-08
Reference number: L-SB-0035-16

INTERMITTENT BATTERY DISCHARGE

INTERMITTENT BATTERY DISCHARGE

TECHNICAL SERVICE BULLETIN

Reference Number(s): L-SB-0035-16, Date of Issue:  July 8, 2016
LEXUS: 2013 - 2014 ES350, GS350; 2014 - 2015 IS250, IS350
SERVICE CATEGORY: Power Source/Network
SECTION: Battery/Charging
COPYRIGHT: © 2018 Lexus, a division of Toyota Motor Sales, USA License Agreement TMS1002

APPLICABILITY

APPLICABILITY

YEAR(S) MODEL(S) ADDITIONAL INFORMATION
2013 - 2014 ES350, GS350  
2014 - 2015 IS250, IS350  

INTRODUCTION

Some 2013 - 2015 model year Lexus ES, GS, and IS vehicles may exhibit an intermittent discharged battery occurring with no apparent source of discharge found. One possible cause may be the Network Gateway Computer not properly going into sleep mode at key OFF. This can result in excessive parasitic draw and a discharged battery condition. Follow the procedure in this bulletin to identify and address this condition.

PRODUCTION CHANGE INFORMATION

This bulletin applies to vehicles equipped with the options and produced BEFORE  the Production Change Effective VINs shown below.

PRODUCTION CHANGE INFORMATION

MODEL DRIVETRAIN EQUIPPED OPTIONS PRODUCTION CHANGE EFFECTIVE VIN
ES350 2WD Blind Spot Monitor or Clearance Warning Sonar JTHBK1GG#E2149103
GS350 AWD Blind Spot Monitor or Lane Departure Alert JTHCE1BL#E5028690
GS350 2WD JTHBE1BL#E5044369
IS250 2WD Blind Spot Monitor or Clearance Warning Sonar JTHBF1D2#F5048786
IS250 AWD JTHCF1D2#F5017491
IS350 2WD JTHBE1D2#F5015465
IS350 AWD JTHCF1D2#F5006395

WARRANTY INFORMATION

WARRANTY INFORMATION

OP CODE DESCRIPTION TIME OFP T1 T2
EL1609 R & R Network Gateway ECU 1.2 89111-33070
89100-30180
89100-30151
87 74

APPLICABLE WARRANTY

PARTS INFORMATION

PARTS INFORMATION

MODEL PART NUMBER PART NAME QTY
PREVIOUS NEW
ES350 89111-33070 89111-33110 Computer, Network Gateway 1
GS350 89100-30180 89100-30181
IS250, IS350 89100-30151 89100-30160

REQUIRED TOOLS & EQUIPMENT

REQUIRED TOOLS & EQUIPMENT

SPECIAL SERVICE TOOLS (SST) PART NUMBER QTY
GR8(1) 00002-MCGR8  1
(1) Essential SST.
NOTE: Additional SSTs may be ordered by calling 1-800-933-8335.
REQUIRED TOOLS & EQUIPMENT

REQUIRED TOOLS & MATERIAL QUANTITY
DVOM (Digital Volt Ohm Meter) 1
REQUIRED TOOLS & EQUIPMENT

REQUIRED EQUIPMENT SUPPLIER PART NUMBER QTY
Techstream 2.0(1) ADE TS2UNIT 1
Techstream Lite TSLITEPDLR01
Techstream Lite (Green Cable) TSLP2DLR01
(1) Essential SST.
NOTE:
  • Only ONE of the Techstream units listed above is required.
  • Software version 11.10.034 or later is required.
  • Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE) at 1-800-368-6787.

REPAIR PROCEDURE

  1. Load test the battery with the GR8 Battery Diagnostic Station.
    1. Select Diagnostic from the Main Menu.
      G10587867Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Repairs to correct a battery fail condition are NOT covered by this TSIB.
      • GR8 Battery Diagnostic Station must be used to test battery.
      • Do NOT use Battery Test function on the Main Menu.
      • Detailed information on battery testing can be found in the Battery Testing and Charging Best Practices Quick Training Guide - QL614C  .

      Did the battery pass the GR8 Diagnostic test?

      • YES -  Proceed to step 2.
      • NO - STOP!  Battery Test fail condition MUST be corrected before continuing with this bulletin.
  2. Start the engine and maintain an engine speed of 2,000 RPM with all accessories OFF.
    1. Verify that the voltage and amperage are within specification:

      Standard amperage: 10 A or less** 

      Standard voltage: 13.2 to 14.8 V 

      ** Battery must be fully charged.

    2. With the engine running at 2,000 RPM, turn the high beam headlights ON and turn the heater blower switch to the "HI" position. Verify that the voltage and amperage are within specification:

      Standard amperage: 30 A or more 

      Standard voltage: 13.2 to 14.8 V 

      G10587868Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Did the Charging System pass the Charging System Test?

    • YES -  Proceed to step 3.
    • NO - STOP!  Charging System fail condition must be corrected before continuing with this bulletin.
    NOTE:
    • Repairs to correct a Charging System Test fail condition are NOT covered by this TSIB.
    • Detailed information on testing the charging system can be found in the Toyota Starting, Charging and Parasitic Draw Tests Quick Training Guide QT611B  .
  3. Loosen the negative (-) battery cable so it will be easy to remove for the test.
    1. Lock the hood latch using a screwdriver and roll the driver's window down.
      NOTE: This closes the hood latch switch and enables the theft deterrent system in case it is the source of the parasitic draw.
      G10587869Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the ignition ON and then OFF.
    3. Turn OFF all electrical loads, close and lock the doors, then wait for the ECUs to go into sleep mode. This may take anywhere from 10 minutes to 2 hours dependent upon which vehicle is being serviced and what equipment is installed in the vehicle.
    4. Attach the negative (-) lead of the ammeter to the negative (-) battery post and the positive lead of the ammeter to the negative (-) battery cable end.
      NOTE:
      • Place leads without disconnecting the battery cable.
      • If the ammeter leads become disconnected from the battery post or battery cable during the test, reconnect the battery and restart the test from step B.
      • If the ammeter leads become disconnected from the battery post or battery cable during the test refer to the applicable repair instructions on TIS for initialization procedures necessary when the battery terminal is disconnected/reconnected.
      • Average milliamp setting should be used. Disregard Minimum and Maximum values for this test.
      G10587870Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the negative (-) battery cable without breaking the circuit between the battery and vehicle, and record the meter reading.
      NOTE:
      • After completing the parasitic draw test remove the screwdriver from the hood latch and operate the hood release lever
      • Verify the hood latch is in the open position before attempting to close the hood.
      G10587871Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard average parasitic draw: 

      Less than 50 milliamps average (0.050 amp)

      Did the system (or vehicle) pass the Parasitic Draw Test?

      • YES -  Proceed to step 4.
      • NO -  Parasitic draw fail condition must be corrected before continuing with this bulletin.
      NOTE:
      • Repairs to correct a Parasitic Draw Test fail condition are NOT covered by this TSIB.
      • Detailed information on testing the parasitic draw can be found in the Toyota Starting, Charging and Parasitic Draw Tests Quick Training Guide QT611B  .
  4. Remove the Network Gateway ECU and check the part number.

    Refer to the Technical Information System (TIS), applicable model and model year Repair Manual:

    • 2013  / 2014  ES350:

      Power Source/Network - Networking - "Networking: Network Gateway ECU: Removal" 

    • 2013  / 2014  GS350:

      Power Source/Network - Networking - "Networking: Network Gateway ECU: Removal" 

    • 2014  / 2015  IS250 / IS350:

      Power Source/Network - Networking - "Networking: Network Gateway ECU: Removal" 

    Is the Network Gateway ECU part number the same as the Previous Part Number shown in the Parts Information section?

    • YES -  Proceed to step 5.
    • NO -  This bulletin does NOT apply. Reinstall network Gateway ECU and continue diagnosis using the applicable Repair Manual.
  5. Install the NEW Network Gateway ECU.

    Refer to TIS, applicable model and model year Repair Manual:

    • 2013  / 2014  ES350:

      Power Source/Network - Networking - "Networking: Network Gateway ECU: Installation" 

    • 2013  / 2014  GS350:

      Power Source/Network - Networking - "Networking: Network Gateway ECU: Installation" 

    • 2014  / 2015  IS250 / IS350:

      Power Source/Network - Networking - "Networking: Network Gateway ECU: Installation" 

  6. Clear Diagnostic Trouble Codes.
  7. Using TIS Techstream, perform a Health Check and confirm no current DTCs are present.
    NOTE: If current DTCs are present, diagnose per Repair Manual procedures.