Initialization [06/2012 - ]
- PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED
Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed References Correct the steering angle neutral point Parking assist monitor system Refer to INITIALIZATION [06/2012 - ] Power trunk lid system not operate Power trunk lid system Refer to INITIALIZATION [06/2012 - ] NOTE:After the engine switch is turned off, the multi-media module receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.
- PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
Replacement Part Necessary Procedure Effect/Inoperative Function when Necessary Procedures are not Performed References ECM Vehicle Identification Number (VIN) registration MIL comes on Refer to REGISTRATION [06/2012 - ] ECU communication ID registration (Immobiliser system) Engine start Refer to REGISTRATION [06/2012 - ] - Throttle body with motor assembly
- Cleaning the deposits from the throttle body with motor assembly
- Engine assembly
- Cylinder head sub-assembly
- Camshaft (for intake or exhaust camshaft)
- Camshaft timing gear assembly
- Camshaft timing exhaust gear assembly
- Piston or piston ring
- Mass air flow meter sub-assembly
- Fuel injector assembly
- Fuel pump
- Air fuel ratio sensor
- Engine coolant temperature sensor
- Spark plug
- Ignition coil assembly
- Air leaks from intake system
- Gas leaks from exhaust system
- Knock control sensor
Inspection after repair Poor idle, engine starting, etc Refer to INITIALIZATION [06/2012 - ] Millimeter wave radar sensor assembly Adjust millimeter wave radar sensor assembly - Dynamic radar cruise control system
- Pre-collision system
Refer to ADJUSTMENT [06/2012 - ] Lane departure warning camera Adjust lane departure warning camera Lane departure alert system Refer to ADJUSTMENT [06/2012 - ] Automatic transaxle assembly - Reset memory
- Input transaxle compensation code into TCM
- Perform road test to allow TCM to learn
- Large shift shock
- Deterioration of fuel efficiency
Refer to INITIALIZATION [06/2012 - ] for Initialization
Refer to REGISTRATION [06/2012 - ] for Registration- Valve body assembly
- Shift solenoid valve SL3 and/or SL4
- Reset memory
- Reset transaxle compensation code
- Perform road test to allow TCM to learn
- Large shift shock
- Deterioration of fuel efficiency
Shift solenoid valve SL1 and/or SL2 Perform road test to allow TCM to learn - Large shift shock
- Deterioration of fuel efficiency
TCM (If possible, read the transaxle compensation code from the previous TCM) Possible - Reset memory
- Transfer transaxle compensation code
- Perform road test to allow TCM to learn
- Large shift shock
- Deterioration of fuel efficiency
Impossible - Reset memory
- Reset transaxle compensation code
- Perform road test to allow TCM to learn
- Large shift shock
- Deterioration of fuel efficiency
- Tire pressure warning ECU and receiver
- Tire pressure warning valve and transmitter
- Transmitter ID registration
- Initialization
- When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.
- Tire pressure warning function
Refer to INITIALIZATION [06/2012 - ] for Initialization
Refer to REGISTRATION [06/2012 - ] for RegistrationSkid control ECU (Brake actuator assembly) Perform the zero point calibration of the yaw rate and acceleration sensor - Slip indicator light illumination
- VSC disabled or malfunctioning
Refer to CALIBRATION [06/2012 - ] Yaw rate and acceleration sensor (Airbag sensor assembly) - Clear the zero point calibration data
- Perform the zero point calibration of the yaw rate and acceleration sensor
- Slip indicator light illumination
- VSC disabled or malfunctioning
Power steering ECU assembly - Torque sensor zero point calibration
- Assist map writing
- EPS warning light comes on
- EPS control
Refer to CALIBRATION [06/2012 - ] Electric power steering column sub-assembly Torque sensor zero point calibration Steering effort is different between turning steering wheel to left and right Multi-media module receiver assembly Parking assist monitor system initialization Parking assist monitor system Refer to CALIBRATION [06/2012 - ] Spiral cable with sensor sub-assembly - Steering angle neutral point (Initialize parking assist monitor system)
- Steering angle setting
Parking assist monitor system Rear television camera assembly Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system Blind spot monitor sensor Blind spot monitor beam axis inspection DTCs are output Refer to OPERATION CHECK [06/2012 - ] - Inner rear view mirror assembly*1
- Garage door opener transmitter*1
Re-registration of codes in the garage door opener system - Register transmitter code
- Rolling code systems
Garage door opener system Refer to REGISTRATION [06/2012 - ] DCM (Telematics Transceiver) DCM activation Safety connect system Refer to DCM ACTIVATION [06/2012 - ] - Certification ECU (smart key ECU assembly)
- ID code box (immobiliser code ECU)
- Main body ECU (multiplex network body ECU)
- Steering lock ECU (steering lock actuator assembly)
- Electrical key transmitter sub-assembly
Code registration (Immobiliser system) - Wireless door lock control system
- Smart access system with push-button start
- Engine start
- Steering lock system
Refer to REGISTRATION [06/2012 - ] - Occupant classification ECU
- Front passenger seat
Zero point calibration and sensitivity check. (Occupant classification system) - Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger)
Refer to INITIALIZATION [06/2012 - ] - No. 1 air conditioning radiator damper servo sub-assembly
- No. 2 air conditioning radiator damper servo sub-assembly
- No. 1 blower damper servo sub-assembly
Initialization servo motor (Air conditioning system) DTCs are output Refer to INITIALIZATION [06/2012 - ] - Power window regulator motor assembly
- Door window regulator assembly
- Door glass
- Door glass run
Initialize power window control system - Auto up/down function
- Jam protection function
- Operation function after engine switch is turned off
- Key-linked function
- Wireless transmitter-linked function*2
- Window open warning
Refer to INITIALIZATION [06/2012 - ] - Sliding roof ECU (sliding roof drive gear sub-assembly)
- Sliding roof glass sub-assembly
- Sliding roof drive cable sub-assembly
Initialize sliding roof ECU (pulse sensor initial position setting) - Automatic slide open/close and tilt up/down function of sliding roof*3
- Automatic open and tilt up function of sliding roof*4
- Jam protection function
- Operation function after engine switch is turned off
- Key-linked function*3
- Wireless transmitter-linked function*2*3
- Sliding roof open warning
Refer to INITIALIZATION [06/2012 - ] - Luggage closer motor assembly
- Luggage door closer assembly
Check power trunk lid function Power trunk lid system Refer to INITIALIZATION [06/2012 - ] - Headlight leveling ECU assembly
- Rear height control sensor sub-assembly
Perform headlight leveling ECU assembly initialization Headlight leveling function Refer to INITIALIZATION [06/2012 - ] - *1: w/ Garage Door Opener System
- *2: w/ Side Marker Light
- *3: for Standard
- *4: for Glass Roof