LEMON Manuals: Even more car manuals for everyone

Engine Assembly: Removal: Removal

  1. REMOVE COOL AIR INTAKE DUCT SEAL 
    1. Remove the 11 clips and intake duct seal.
      Fig 1: Identifying Cool Air Intake Duct Seal Clips
      GTY145917Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. REMOVE ENGINE ROOM SIDE COVER LH 
    1. Remove the 5 clips and side cover.
      Fig 2: Identifying Engine Room Side Cover Clips
      GTY126144Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE ENGINE ROOM SIDE COVER RH 
    1. Remove the 2 clips and side cover.
      Fig 3: Identifying Engine Room Side Cover Clips
      GTY125750Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE V-BANK COVER SUB-ASSEMBLY 
    1. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.
      Fig 4: Removing/Installing V-Bank Cover
      GTY143953Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Attempting to disengage both front and rear clips at the same time may cause the cover to break.

  5. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM  . Refer to REPLACEMENT - Step 1
  6. DISCHARGE FUEL SYSTEM PRESSURE 

    HINT: 

    Refer to PRECAUTION .

  7. PLACE FRONT WHEELS FACING STRAIGHT AHEAD 
  8. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
  9. REMOVE FRONT WHEEL 
  10. REMOVE ENGINE UNDER COVER 
  11. REMOVE NO. 2 ENGINE UNDER COVER (for 2WD) 
  12. REMOVE ENGINE UNDER COVER REAR LH (for 2WD) 
    1. Remove the bolt and engine under cover LH.
      Fig 5: Identifying Engine Under Cover
      GTY123519Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE ENGINE UNDER COVER REAR RH (for 2WD) 

    HINT: 

    Remove the RH side following the same procedures as with the LH side.

  14. DRAIN ENGINE OIL  . Refer to REPLACEMENT - Step 1
  15. DRAIN ENGINE COOLANT  . Refer to ON-VEHICLE INSPECTION - Step 4
  16. DRAIN FRONT DIFFERENTIAL OIL (for 4WD)  . Refer to REMOVAL - Step 1
  17. REMOVE FRONT EXHAUST PIPE ASSEMBLY 

    HINT: 

    Refer to REMOVAL .

  18. REMOVE PROPELLER SHAFT ASSEMBLY WITH CENTER BEARING 

    HINT: 

  19. REMOVE NO. 1 INLET AIR CLEANER 
    1. Remove the bolt, clip and inlet air cleaner.
      Fig 6: Locating Inlet Air Cleaner Bolt & Clip
      GTY145834Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE  . Refer to REMOVAL - Step 6
  21. REMOVE AIR CLEANER CASE SUB-ASSEMBLY 
    1. Remove the 2 bolts, clamp and air cleaner case.
      Fig 7: Locating Air Cleaner Case And Clamp
      GTY145835Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. DISCONNECT UNION TO CHECK VALVE HOSE 
    1. Remove the clamp and disconnect the union to check valve hose.
  23. DISCONNECT NO. 2 FUEL VAPOR FEED HOSE 
    1. Remove the clamp and disconnect the No. 2 fuel vapor feed hose.
      Fig 8: Locating No. 2 Fuel Vapor Feed Hose
      GTY139946Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  24. DISCONNECT INLET RADIATOR HOSE 
    1. Remove the clamp and disconnect the inlet radiator hose.
      Fig 9: Identifying Inlet Radiator Hose And Clamp
      GTY131846Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  25. DISCONNECT OUTLET RADIATOR HOSE 
    1. Remove the clamp and disconnect the outlet radiator hose.
  26. DISCONNECT RADIATOR RESERVOIR TANK HOSE 
    1. Remove the clamp and disconnect the radiator reservoir tank hose.
  27. DISCONNECT INLET HEATER WATER HOSE 
    1. Disconnect the inlet heater water hose.
      Fig 10: Identifying Inlet Heater Water Hose
      GTY133078Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. DISCONNECT OUTLET HEATER WATER HOSE 
    1. Disconnect the outlet heater water hose.
      Fig 11: Identifying Inlet Heater Water Hose
      GTY145829Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. REMOVE NO. 1 COOLER REFRIGERANT SUCTION HOSE  . Refer to REMOVAL - Step 8
  30. REMOVE DISCHARGE HOSE SUB-ASSEMBLY  . Refer to REMOVAL - Step 9
  31. REMOVE ECM COVER  . Refer to REMOVAL - Step 4
  32. DISCONNECT ENGINE WIRE 
    1. Disconnect the 6 ECM connectors.
    2. Using a screwdriver, disconnect the connector holder.
      Fig 12: Identifying Connector Holder
      GTY145867Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the engine room No. 1 relay block cover.
    4. Remove the nut and disconnect the wire from the engine room No. 1 junction block.
      Fig 13: Locating Engine Room No. 1 Junction Block
      GTY132072Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the nut and disconnect the battery positive (+) cable.
    6. Disconnect the connector and remove the 4 clamps from body.
    7. Remove the bolt, clamp and engine wire No. 3.
      Fig 14: Identifying Engine Wire No. 3, Bolt & Clamp
      GTY145831Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Remove the bolt and disconnect the ground cable.
  33. DISCONNECT FUEL MAIN TUBE 

    HINT: 

    Refer to PRECAUTION .

  34. DISCONNECT NO. 3 FUEL HOSE 
    1. Remove the clamp and disconnect the No. 3 fuel hose.
      Fig 15: Identifying No. 3 Fuel Hose & Pipe
      GTY101538Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. DISCONNECT FUEL TUBE SUB-ASSEMBLY 
    1. Remove the fuel pipe clamp.
      Fig 16: Identifying Fuel Pipe Clamp
      GTY145732Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Pinch and pull the fuel tube's connector to disconnect it from the fuel tube sub-assembly.
      Fig 17: Identifying Fuel Tube Sub-Assembly Connector
      GTY121060Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Check for foreign matter in the fuel tube around the fuel tube's connector. Clean it if necessary. Foreign matter can affect the O-ring's ability to seal the connector and fuel main pipe.
      • Do not use any tools to separate the connector and pipe.
      • Do not forcefully bend or twist the hose.
      • Keep the connector and pipe free from foreign matter.
      • If the connector and pipe are stuck together, pinch the connector and turn it carefully to disconnect it.
      • Put the connector in a plastic bag to prevent damage and contamination.
  36. REMOVE FRONT LOWER SUSPENSION MEMBER PROTECTOR (for 2WD) 
    1. Remove the 4 bolts and suspension member protector.
      Fig 18: Identifying Suspension Member Protector & Bolts
      GTY101206Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  37. DISCONNECT STEERING SLIDING WITH SHAFT YOKE SUB-ASSEMBLY (for 2WD)  . Refer to REMOVAL - Step 7
  38. DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for 4WD)  . Refer to REMOVAL - Step 5
  39. SEPARATE FRONT SPEED SENSOR LH (for 4WD)  . Refer to REMOVAL - Step 3
  40. SEPARATE FRONT SPEED SENSOR RH (for 4WD) 

    HINT: 

    Remove the RH side following the same procedures as with the LH side.

  41. REMOVE FRONT AXLE HUB LH NUT (for 4WD)  . Refer to REMOVAL - Step 5
  42. REMOVE FRONT AXLE HUB RH NUT (for 4WD) 

    HINT: 

    Remove the RH side following the same procedures as with the LH side.

  43. REMOVE TIE ROD ASSEMBLY LH (for 4WD)  . Refer to REMOVAL - Step 12
  44. REMOVE TIE ROD ASSEMBLY RH (for 4WD) 

    HINT: 

    Remove the RH side following the same procedures as with the LH side.

  45. DISCONNECT HEIGHT CONTROL SENSOR LINK (for 2WD) 
    1. Remove the nut and disconnect the height control sensor link.
      Fig 19: Identifying Height Control Sensor Link Bolt
      GTY131863Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  46. DISCONNECT HEIGHT CONTROL SENSOR LINK (for 4WD) 
    1. Remove the bolt and disconnect the height control sensor link.
      Fig 20: Identifying Height Control Sensor Link (4WD)
      GTY145833Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  47. REMOVE FRONT SHOCK ABSORBER ASSEMBLY LH (for 2WD) 
    1. Loosen the bolt while holding the nut. Separate the lower part of the front shock absorber from the front suspension lower arm.
      Fig 21: Identifying Front Shock Absorber Lower Bolt
      GTY126719Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  48. REMOVE FRONT SHOCK ABSORBER ASSEMBLY RH (for 2WD) 

    HINT: 

    Remove the RH side following the same procedures as for the LH side.

  49. REMOVE FRONT SHOCK ABSORBER ASSEMBLY LH (for 4WD) 
    1. Loosen the bolt and separate the lower part of the front shock absorber from the front absorber bracket lower.
      Fig 22: Identifying Front Shock Absorber Assembly RH (For 4WD)
      GTY104798Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  50. REMOVE FRONT SHOCK ABSORBER ASSEMBLY RH (for 4WD) 

    HINT: 

    Remove the RH side following the same procedures as for the LH side.

  51. REMOVE FRONT LOWER BALL JOINT ASSEMBLY LH (for 2WD) 
    1. Remove the 2 bolts from the front lower ball joint.
      Fig 23: Identifying Lower Ball Joint & Bolts (For 2WD)
      GTY102251Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  52. REMOVE FRONT LOWER BALL JOINT ASSEMBLY RH (for 2WD) 

    HINT: 

    Remove the RH side following the same procedures as for the LH side.

  53. REMOVE FRONT LOWER BALL JOINT ASSEMBLY LH (for 4WD) 
    1. Remove the 2 bolts from the front lower ball joint.
      Fig 24: Removing/Installing Front Lower Ball Joint LH (4WD)
      GTY108533Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  54. REMOVE FRONT LOWER BALL JOINT ASSEMBLY RH (for 4WD) 

    HINT: 

    Remove the RH side following the same procedures as for the LH side.

  55. SEPARATE FRONT AXLE ASSEMBLY LH (for 4WD)  . Refer to REMOVAL - Step 8
  56. REMOVE FRONT AXLE ASSEMBLY RH (for 4WD) 

    HINT: 

    Remove the RH side following the same procedures as for the LH side.

  57. DISCONNECT POWER STEERING LINK WIRE HARNESS (for 2WD) 
    1. Remove the bolt (A) to disconnect the earth wire from the bracket.
      Fig 25: Identifying Power Steering Link Wire Harness
      GTY134968Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 2 clamps to disconnect the wire harness from the bracket.
    3. Disconnect the 2 connectors (C) and (D) from the power steering link assembly.
    4. Release the lock of connector (E) and disconnect the connector from the power steering link assembly.
    5. Remove the bolt (B) and the power steering earth wire from the power steering link assembly.
  58. DISCONNECT POWER STEERING LINK WIRE HARNESS (for 4WD) 
    1. Remove the bolt (A) and the power steering earth wire from the power steering link assembly.
      Fig 26: Disconnecting Power Steering Link Wire Harness (For 4WD)
      GTY359901Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt (B) to disconnect the earth wire from the bracket.
    3. Remove the 2 clamps to disconnect the wire harness from the front frame.
    4. Disconnect the 2 connectors (C) and (D) from the power steering link assembly.
    5. Release the lock of connector (E) and disconnect the connector from the power steering link assembly.
    6. Remove the bolt (F) to disconnect the bracket from the front frame.
  59. DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY (for 2WD)  . Refer to REMOVAL - Step 18
  60. DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY (for 4WD)  . Refer to REMOVAL - Step 14
  61. REMOVE ENGINE AND TRANSMISSION ASSEMBLY (for 2WD) 
    1. Set the engine lifter.
    2. Remove the 4 bolts, then separate the engine rear mounting member.
      Fig 27: Locating Engine Rear Mounting Member And Bolt
      GTY114282Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 12 bolts shown in the illustration.
      Fig 28: Identifying 12 Engine And Transmission Assembly Bolts
      GTY145625Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Operate the engine lifter, then slowly remove the engine from the vehicle.
      NOTE:

      Make sure that the engine is clear of all wiring and hoses.

  62. REMOVE ENGINE AND TRANSMISSION ASSEMBLY (for 4WD) 
    1. Set the engine lifter.
    2. Remove the 4 bolts, then separate the engine rear mounting member.
      Fig 29: View Of Separating Engine Rear Mounting Member
      GTY101385Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 8 bolts shown in the illustration.
      Fig 30: Removing Engine And Transmission Assembly Bolts
      GTY347504Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Operate the engine lifter, then slowly remove the engine from the vehicle.
      NOTE:

      Make sure that the engine is clear of all wiring and hoses.

  63. INSTALL ENGINE HANGERS 
    1. Install the No. 1 and No. 2 or No. 3 engine hangers with the 4 bolts as shown in the illustration.
      Fig 31: Identifying Engine Hangers & Bolts
      GTY104715Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 33 N.m (336 kgf cm, 24 ft. lbf) 

      PART NO.:

      No. 1 engine hanger 12281 - 31070
      No. 2 engine hanger 12282 - 31050 (2WD)
      No. 3 engine hanger 12283 - 31010 (4WD)
      Bolts 91671 - 10825
    2. Attach an engine sling device and hang the engine with a chain block.
  64. REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)  . Refer to REMOVAL - Step 2
  65. REMOVE STARTER ASSEMBLY  . Refer to REMOVAL - Step 11
  66. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY 

    HINT: 

  67. REMOVE OIL DIPSTICK GUIDE SUB-ASSEMBLY (for 2WD) 
    1. Remove the oil level gauge.
      Fig 32: Identifying No. 2 Oil Dipstick Guide And Bolts
      GTY145832Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt, then remove the No. 2 oil dipstick guide.
    3. Remove the O-ring from the No. 2 oil dipstick guide.
    4. Remove the bolt and clamp, then remove the No. 1 oil dipstick guide.
      Fig 33: Locating No. 1 Oil Dipstick Guide, Bolt And Clamp
      GTY100108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the O-ring from the No. 1 oil dipstick guide.
  68. REMOVE OIL DIPSTICK GUIDE SUB-ASSEMBLY (for 4WD) 
    1. Remove the oil level gauge.
      Fig 34: Identifying No. 2 Oil Dipstick Guide With Bolt
      GTY104799Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt, then remove the No. 2 oil dipstick guide.
    3. Remove the O-ring from the No. 2 oil dipstick guide.
    4. Remove the bolt, then remove the No. 1 oil dipstick guide.
      Fig 35: Identifying No. 1 Oil Dipstick Guide With Bolt
      GTY104800Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the O-ring from the No. 1 oil dipstick guide.
  69. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH 
    1. Disconnect the heated oxygen sensor connector.
    2. Remove the 6 nuts, exhaust manifold and gasket.
      Fig 36: Identifying Exhaust Manifold Nuts
      GTY136533Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  70. INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY LH 
    1. Using a precision straightedge and feeler gauge, measure the warpage on the contact surface of the cylinder head.
      Fig 37: Inspecting Exhaust Manifold Sub-Assembly LH
      GTY146281Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Maximum warpage

      0.7 mm (0.028 in.)

      HINT: 

      The maximum allowable warpage of each installation surface is 0.3 mm (0.012 in.).

      If the warpage is greater than the maximum, replace the manifold.

  71. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH 
    1. Disconnect the heated oxygen sensor connector.
    2. Remove the 6 nuts, exhaust manifold and gasket.
      Fig 38: Identifying Exhaust Manifold Nuts
      GTY104576Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  72. INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY RH 
    1. Using a precision straightedge and feeler gauge, measure the warpage on the contact surface of the cylinder head.
      Fig 39: Inspecting Exhaust Manifold Sub-Assembly RH
      GTY139071Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Maximum warpage

      0.7 mm (0.028 in.)

      HINT: 

      The maximum allowable warpage of each installation surface is 0.3 mm (0.012 in.).

      If the warpage is greater than the maximum, replace the manifold.

  73. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH (for 4WD)  . Refer to REMOVAL - Step 9
  74. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)  . Refer to REMOVAL - Step 10
  75. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY 
    1. Using SST, hold the crankshaft.
      Fig 40: Holding Crankshaft
      GTY135273Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • SST: 09213-70011 
        1. 09213-70020
      • SST: 09330-00021 
    2. Remove the 8 bolts, front spacer, drive plate and rear spacer.
      Fig 41: Identifying Drive Plate Bolts
      GTY144194Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  76. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY (for 2WD) 
    1. Remove the 2 bolts, then separate the front suspension crossmember sub-assembly from the engine.
      Fig 42: Locating Front Suspension Crossmember Sub-Assembly Bolts
      GTY145918Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  77. REMOVE FRONT FRAME ASSEMBLY (for 4WD) 
    1. Remove the 2 bolts, then separate the front frame assembly from the engine.
      Fig 43: Identifying Front Frame Assembly Bolts (4WD)
      GTY132869Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  78. FIX ENGINE ON ENGINE STAND 
    1. Fix the engine onto a engine stand with the bolts.
  79. REMOVE V-RIBBED BELT  See step  4
  80. REMOVE NO. 2 ENGINE COVER 
    1. Remove the 3 clips and clamp, then remove the No. 2 engine cover.
      Fig 44: Identifying No. 2 Engine Cover, Clips & Clamp
      GTY101533Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  81. REMOVE NO. 1 ENGINE COVER 
    1. Remove the 3 clips, then remove the No. 1 engine cover.
      Fig 45: Locating No 1 Engine Cover With Clips
      GTY102185Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  82. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY 
    1. Remove the bolt, plate and idler pulley.
      Fig 46: Locating Idler Pulley Bolt
      GTY104795Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  83. REMOVE GENERATOR ASSEMBLY  . Refer to REMOVAL - Step 12
  84. REMOVE COOLER COMPRESSOR ASSEMBLY (for 2WD)  . Refer to REMOVAL - Step 10
  85. REMOVE OIL FILTER BRACKET (for 4WD)  . Refer to REMOVAL - Step 7
  86. REMOVE COOLER COMPRESSOR ASSEMBLY (for 4WD)  . Refer to REMOVAL - Step 11
  87. REMOVE ENGINE MOUNTING BRACKET LH 
    1. Disconnect the 2 clamps.
      Fig 47: Identifying Bolts & Mounting Bracket (LH)
      GTY136113Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 4 bolts and mounting bracket.
  88. REMOVE ENGINE MOUNTING BRACKET RH 
    1. Remove the 4 bolts and mounting bracket.
      Fig 48: Identifying Bolts & Mounting Bracket (RH)
      GTY121672Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  89. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY 
    1. Remove the 5 bolts, then remove the V-ribbed belt tensioner assembly. (2WD)
      Fig 49: Identifying V-Ribbed Belt Tensioner Assembly
      GTY360003Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 4 bolts, then remove the V-ribbed belt tensioner assembly. (4WD)
  90. REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)  . Refer to REMOVAL - Step 3
  91. REMOVE WATER PUMP PULLEY  . Refer to REMOVAL - Step 21
  92. REMOVE ENGINE WIRE 
    1. Remove the engine wire from the engine.
  93. REMOVE INJECTOR DRIVER 
    1. Remove the bolt, 2 nuts and injector driver.
      Fig 50: Identifying Injector Driver Bolt & Nuts
      GTY103208Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  94. REMOVE INTAKE AIR SURGE TANK ASSEMBLY 

    HINT: 

    Refer to REMOVAL

  95. INSPECT INTAKE AIR SURGE TANK ASSEMBLY 
    1. Using a precision straightedge and feeler gauge, measure the warpage on the contact surface of the cylinder head.
      Fig 51: Measuring Warpage On Contact Surface Of Cylinder Head
      GTY104910Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Maximum warpage

      2.5 mm (0.098 in.)

      If the warpage is greater than the maximum, replace the surge tank.

  96. REMOVE NO. 2 SURGE TANK STAY 
    1. Remove the bolt and No. 2 surge tank stay.
  97. REMOVE WATER HOSE JOINT 
    1. Remove the bolt, and disconnect 2 hoses and water hose joint.
      Fig 52: Identifying Water Hose Joint And Bolt
      GTY104801Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  98. REMOVE INTAKE MANIFOLD  . Refer to REMOVAL - Step 20
  99. INSPECT INTAKE MANIFOLD 
    1. Surge tank side:
      Fig 53: Measuring Warpage On Contact Surface Of Cylinder Head
      GTY140039Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Using a precision straightedge and feeler gauge, measure the warpage on the contact surface of the cylinder head.

        Maximum warpage

        0.1 mm (0.003 in.)

        If the warpage is greater than the maximum, replace the intake manifold.

    2. Cylinder head side:
      1. Using a precision straightedge and feeler gauge, measure the warpage on the contact surface of the cylinder head.

        Maximum warpage

        0.1 mm (0.003 in.)

        If the warpage is greater than the maximum, replace the intake manifold.

  100. REMOVE FUEL TUBE SUB-ASSEMBLY 
    1. Remove the 2 bolts and fuel tube sub-assembly.
      Fig 54: Identifying Fuel Tube Sub-Assembly Bolts
      GTY129901Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  101. REMOVE FUEL PUMP 

    HINT: 

    Refer to REMOVAL .

  102. REMOVE FUEL INJECTOR ASSEMBLY 

    HINT: 

    Refer to REMOVAL .

  103. REMOVE KNOCK SENSOR  . Refer to REMOVAL - Step 28
  104. REMOVE V-BANK COVER BRACKET SUB-ASSEMBLY 
    1. Remove the bolt and V-bank cover bracket.
      Fig 55: Locating V-Bank Cover Bracket Bolt
      GTY101160Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  105. REMOVE IGNITION COIL ASSEMBLY 
    1. Remove the 6 bolts and 6 ignition coils.
  106. REMOVE ENGINE OIL LEVEL SENSOR 
    1. Remove the 4 bolts, then remove the oil level sensor and gasket.
      Fig 56: Identifying Bolts, Oil Level Sensor & Gasket
      GTY145919Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  107. REMOVE OIL PRESSURE SWITCH ASSEMBLY 
    1. Using a 24 mm deep socket wrench, remove the oil pressure switch.
      Fig 57: Identifying Oil Pressure Switch
      GTY145922Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  108. REMOVE ENGINE COOLANT TEMPERATURE SENSOR 
    1. Using a 19 mm deep socket wrench, remove the temperature sensor.
      Fig 58: Identifying Engine Coolant Temperature Sensor, Deep Socket Wrench & Gasket
      GTY104717Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002